I need a wiring diagram for the spark plug wires. or from left to right from the spark plugs- to the bottom connections, how do i wire them. i need step by step directions for each spark plug wire. i need to know exactly where each one goes please and thank you. 1993 saturn sedan sl 1.9 litre single head

Here is the firing order and spark plug wire routing diagram for a 2006 Chevy Impala LT 3.9 V6:
Firing order: 1-2-3-4-5-6
Spark plug wire routing (starting from the driver's side):

• Cylinder 1: connect to the coil tower closest to the driver's side headlight
• Cylinder 3: connect to the coil tower next to cylinder 1
• Cylinder 5: connect to the coil tower next to cylinder 3
• Cylinder 2: connect to the coil tower closest to the passenger side headlight
• Cylinder 4: connect to the coil tower next to cylinder 2
• Cylinder 6: connect to the coil tower next to cylinder 4

Note: Make sure to route the wires properly to avoid cross-firing.

I\'m assuming you have the 3.8 engine,although i believe the firing order is the same on all there v6 sideways mounted front wheel drive Windstars. That firing order is 1-4-2-5-3-6, with 1-2-3 going from left to right on the back side of the engine and 4-5-6 left to right on the front side of the engine.Looking straight down at the coil from the front of the car,you\'ll see 2 rows of coil terminals.The row on the right side is 1-2-3 going from top to bottom,row on left side is 6-5-4 going from top to bottom. Hook the number 1 coil terminal to the number 1 spark plug ,being careful to use the spark plug wire that is closest in length to the length you need. If your just replacing wires,yuo shouldn\'t have to much trouble. If your nreplacing the spark plugs you will find the ones in the rear,especially the number 2 [the middle one} are pretty difficult without removing the cowling. A total pain brought to you by the designers at Ford!

Inspection

Inspect for the correct routing of the spark plug wires. Improper routing may cause cross-firing. Inspect each wire for any signs of cranks or splits in the wire. Inspect each plug wire boot for tearing, piercing, arcing, carbon tracking or a corroded terminal.
If there is any corrosion, carbon tracking or arcing indicated on a plug wire boot or terminal, both the plug wire and component it was connected to should be replaced.

Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the left side spark plug wires from the spark plugs.
3. Remove the left side plug wires from the retaining clips.
4. Rotate the engine for access as follows:
   1. Set the parking brake.
   2. Shift the transaxle into neutral.
   3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
   4. Install the Engine Tilt Strap J-41131.
   5. Pull on the engine in order to rotate the engine forward.
   6. Tighten the strap.
   
   
5. Remove the right side spark plug wires from the spark plugs.
6. Remove the plug wires from the retaining clip.
7. Remove the spark wires from the ignition coils.
8. Remove the plug wire assembly from the engine.
   NOTE If you are replacing the spark plug wires, the spark plug wire conduit and retaining clips should be transferred to the replacement wires.
   

To install:

1. Install the right side plug wires to the ignition coils and then the spark plugs.
2. Install the spark plug wires to the retaining clip.
3. Rotate the engine back to the original position.
4. Install the left side spark plug wires to the ignition coils and then to the spark plugs.
5. Install the spark plug wires to the retaining clips.

3.9L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
2. Remove the intake manifold cover.
3. Remove the left side spark plug wires as follows:
   1. Disconnect the left side spark plug wires from the spark plugs.
   2. Disconnect the left side spark plug wires from the ignition coil.
   3. Remove the left side spark plug wire clips from the intake manifold and heater inlet and outlet pipe.
   4. Remove the left side spark plug wire assembly.
   
   
4. If removing the right side spark plug wires, the engine must be rotated for access as follows:
   1. Set the parking brake.
   2. Shift the transaxle into neutral.
   3. Remove the engine mount strut bolts. Swing the engine mount struts aside.
   4. Install the Engine Tilt Strap J-41131.
   5. Pull on the engine in order to rotate the engine forward.
   6. Tighten the strap.
   
   
5. After rotating the engine, remove the right side spark plug wires as follows:
   1. Disconnect the right side spark plug wires from the spark plugs and ignition coil.
   
   
6. Remove the right side spark plug wire clip from the ignition coil bracket.
7. Remove the right side spark plug wire assembly.

To install:

1. Install the spark plug wire assembly.
2. Install the right side spark plug wire clip at the ignition coil bracket.
3. Connect the plug wires to the ignition coil and spark plugs.
4. If the engine was rotated for access, return the engine to the original position.
5. The remainder of the installation is the reverse order of removal.

..............................

Hope this is helpful.

on the coil pack the one all the way to the left thats #4 then going from left to right #4-#1 #2 #3
4123 on the coil pack
then on the engine the spark plug closet to the top engine mount is #1 then 234 from left to right 1234 on the engine

I can't upload the diagram but the firing order appears to be 1,4,6,3,2,5

Install the spark plug wire(s) (1, 3 and 5) to the engine right side spark plug(s).

Install the spark plug wire(s) to the retaining clips.

Install the spark plug wire(s) (2, 4 and 6) to the engine left side spark plug(s).

Install the spark plug wire(s) to the retaining clips.

You can get a copy of the service manual from Promanuals.net for cheap.

2003 Chevrolet Malibu 3.1L SFI OHV 6cyl
Spark Plug Wires - Removal & Installation

3.5L Engine

1. Before servicing the vehicle, refer to the Precautions Section.
   NOTE Twist the spark plug boot one-half turn in order to release the boot. Pull on the spark plug boot only. Do not pull on the spark plug wire or the wire could be damaged.
2. Remove the intake manifold cover, if required.
3. Disconnect the left side spark plug wires from the spark plugs.
4. Disconnect the left side spark plug wires from the ignition coil.
5. Remove the spark plug wire clips from the Manifold Absolute Pressure (MAP) sensor bracket and the heater inlet and outlet pipe tab.
6. Remove the spark plug wire assembly.
7. If replacing only one plug wire, open the retaining clips and remove the appropriate spark plug wire.
8. Disconnect the right side spark plug wires from the spark plugs.
9. Disconnect the right side spark plugs from the ignition coils.
10. Remove the spark plug wire assembly.
11. If replacing only one plug wire, open the retaining clip and remove the appropriate spark plug wire.

To install:

1. Install the spark plug wire assembly.
2. Connect the right side spark plugs to the ignition coils.
3. Connect the right side spark plug wires to the spark plugs.
4. If replacing only one plug wire, open the retaining clip and install the appropriate spark plug wire.
5. Install the spark plug wire assembly.
6. Connect the left side spark plug wires to the spark plugs.
7. Connect the left side spark plug wires to the ignition coil.
8. Install the spark plug wire clips to the MAP sensor bracket and the heater inlet and outlet pipe tab.
9. If replacing only one plug wire, open the retaining clips and install the appropriate spark plug wire.
10. Install the intake manifold cover, if required.

Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 3.5L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.4L Engine Firing order: 1-3-4-2 Distributorless ignition system



Fig. 3.1L Engine Firing order: 1-2-3-4-5-6 Distributorless ignition system



Fig. 2.2L Engine Firing Order: 1-3-4-2 Distributorless ignition system


Fig. 3.5L & 3.9L Engines Firing order: 1-2-3-4-5-6 Distributorless ignition system


I really hope help you with this (remember rated this help) Good luck.

FROM LEFT TO RIGHT, 5/2 3/6 4/1. ASSUMING YOU HAVE THE 3.1L ENGINE.

Follow the wires from your ignition coil (located at the drivers side of the engine) to the spark plugs. Unplug these wires. Using a 5/8" sprak plug socket (deep well with a bit of rubber at the bottom to protect the union of the wire to the plug), unthread the spark plugs. Place new plugs in the cylinder heads (you can use a thread protector available at the counter of most auto parts stores). Plug your new wires into the newly installed new spark plugs. The ignition coil has a diagram telling you which port is for which cylinder. On the V-6 3.0L Vulcan engine the rear bank from left to right is 1-2-3 and the front bank from left to right is 4-5-6. There you have it.