Good Day,
See the pic's
here's a few more for refrence:
To install:
Lift the tensioner, and install the belt onto pulleys. Make sure the belt is routed properly.For 1996-99 vehicles, raise and safely support the vehicle. Install the engine mounting bracket lower spacer, stud and nut.
For 1996-99 supercharged engines, perform the following:
Attach the connector to the crank sensor.
Install the right-hand splash shield, then carefully lower the vehicle.
Install the belt guard or reservoir.
Connect the negative battery cable.
Also perform the following to gain access ti install the new belt
Remove the belt guard or coolant recovery reservoir as required.
For 1996-99 supercharged engines, Raise and safely support the vehicle.
Remove the right-hand splash shield.
Remove the connector from the crank sensor.
Disconnect the negative battery cable.
Fig. 7: Many vehicles have an accessory drive belt routing label affixed to the radiator shroudRemove the belt guard or coolant recovery reservoir as required.
For 1996-99 supercharged engines, perform the following:
Raise and safely support the vehicle.
Remove the right-hand splash shield.
Remove the connector from the crank sensor.
For 1996-99 vehicles, remove the engine mounting bracket lower nut, stud and spacer. Carefully lower the vehicle.
CAUTION
To avoid personal injury when rotating the serpentine belt tensioner, use a tight fitting wrench that is at least 24 in. (61cm) long.Take note of the belt's routing. Lift or rotate the tensioner using a suitable sized breaker bar in the square opening or box end wrench on the pulley nut. Remove the belt from the pulleys.
Fig. 8: You can use a box-end wrench on the pulley nut to rotate the tensioner ...
Fig. 9: ... then remove the belt from the pulleys
Fig. 10: Serpentine drive belt routing and removal - 3.8L (VIN L) engine shown, VIN C similar
Fig. 11: Make sure to note the drive belt routing prior to removing it - 3.8L (VIN K) engine shown
Fig. 12: Drive belt removal on a 1992-95 supercharged engineTo install:
Be sure the belt is aligned into the proper grooves of the accessory drive pulleys.Lift the tensioner, and install the belt onto pulleys. Make sure the belt is routed properly.
Fig. 13: Many vehicles have a label you can check to be sure the belt is installed and routed correctlyFor 1996-99 vehicles, raise and safely support the vehicle. Install the engine mounting bracket lower spacer, stud and nut.
For 1996-99 supercharged engines, perform the following:
Attach the connector to the crank sensor.
Install the right-hand splash shield, then carefully lower the vehicle.
Install the belt guard or reservoir.
Connect the negative battery cable.
×
The leSabre has a three point motor mount. The belt runs through the middle. The lower mount is a light brace; it doesn't seem to really support much.
The mount is a spacer tube a couple inches long. It's held in place by a stud. Remove the stud and the space tube comes out and the belt comes through that opening!!!
Jack up the right side of the car. Pull the plastic splash shield out of the way and prop it with something. You might want to take the wheel off and lower the jack some. There's nut around the stud. Then the end of the stud has a torx male end. Requires female torx socket. I don't recall the size. Check yours out since it's two years earlier, it may have a different setup.
The suggestion is to support the engine lightly when removing that stud. You're not supposed to use a piece of wood lightly under the oil pan, but some do. I saw someone raise the left side of the car slightly to support the motor. They left the wheel in place not jacket up.
The belt goes around the crank pulley, up the left side to the alternator, wraps around the power steering pump and down to the tensioner pulley, back up onto the alternator, then down and around the inside of the water pump. Not between the motor mount and the pulley.
If you have AC it goes from the alernator to the AC compressor, then back up to the water pump and down to the crank.
Remove the lower bolt on the engine mount housing, then remove the spacer. The belt will slip right through.
Check this link for the Manual.....
http://www.2carpros.com/kpages/auto_repa...
×
remove the spacer from the front motor mount, remove tension from the belt, then remove the belt.(reverse to install) Thanks for using Fixya
There should be a diagram under the hood on the frame near the hood latch.
Here's a step-by-step guide from AutoZone
Crank shaft flywheel marks and camshaft marks must be aligned at corresponding position when belt is fitted at .Turn manually engine one complete turn after belt is replaced to ensure that.
SOURCE: 1995 buick rivera serpentine belt install?
look around under the hood , on the underside of the hood, sometimes the belt routing diagram is on a sticker also check a Chiltons Manual sold at auto pARTS STOReS or on the web
14,407 views
Usually answered in minutes!
You did not answer my question
1995 Buick LeSabre Custom Serpentine Belt installation; I need an installation diagram to show me the proper way to replace a removed belt.
1998 lesabre serpentine belt diagram
the diagram in the book shows the belt going up the left side of water pump but there is one leg of the engine mount bracket so close that the belt wont fit in between it and the pulley
I do not have the diagram for the serpentine belt routing. it is not under the hood. I have a 1995 buick LeSabre with a 3.8 engine, custom. with a/c. Is there anyway you can send me the diagram a.s.a.p
×