Graphics display module/vehicle information center

How to turn the lights on the information center, in a 1996 Jeep grand cherokee

working blind, no FSM sounds like it? factory service manual.
easter egg hunts,

climate control box.
the panel (control)

1. Disconnect and isolate the negative battery cable.
2. Remove the center bezel from the instrument panel and place it on a workbench.
3. Remove the screws that secure the electronic vehicle information center (EVIC) control and the A/C-heater control to the center bezel and remove the controls.

or
the automatic control zone module, option? AXC its called
The AXCM it it.

you scanned it and the DTC logs prove it bad.
FSM qoutes
The AZC control module is capable of three different
types of self-diagnostic tests, as follows:
² Fault Code Tests
² Input Circuit Tests
² Output Circuit/Actuator Tests
The information that follows describes:
² How to read the self-diagnostic display
² How to enter the AZC control module self-diagnostic
test mode
² How to select the self-diagnostic test types
² How to perform the different tests
and
To enter the AZC self-diagnostic mode, perform the
following:
(1) Depress the A/C and Recirc buttons at the
same time and hold. Rotate the left temperature control
knob clockwise (CW) one detent.
(2) If you continue to hold the A/C and Recirc buttons
depressed, the AZC control module will perform
a Segment Test of the vacuum fluorescent (VF) display.
In the Segment Test you should see all of the
display segments illuminate as long as both buttons
are held. If a display segment fails to illuminate, the
vacuum fluorescent display is faulty and the heater-
A/C control must be replaced.
(3) After viewing the Segment Test, release the
A/C and Recirc buttons and the display will clear
momentarily. If a 0 is displayed, then no faults
are set in the system.

remove
find it,
unplug it
unscrew it
its out.


is it not inside this part?
http://www.ebay.ca/itm/99-02-Grand-Cherokee-WJ-AZC-Automatic-Zone-Control-Digital-Climate-AC-Heater-J/331385209420?_trksid=p2047675.c100011.m1850&_trkparms=aid%3D222007%26algo%3DSIC.MBE%26ao%3D1%26asc%3D20140620075055%26meid%3Dc65ed9b0ea294f58ab9db96ebd916c19%26pid%3D100011%26rk%3D4%26rkt%3D10%26sd%3D321318868998

did you read the schematic yet?
use a volt meter to find cause?
see wiring here, under ZJ
for why lamps fail,
function display, so what function does it display?
there are many options on these cars, transmission, 4wd types.
and other.
if a lamp dont glow, say what it does. then tell what it does wrong
out, stuck one,? or?

point finger to IT.
http://photos4.automanager.com/024611/660ec5b5c0e44da0a126bcdb4ae17deb/83837c0776_640.jpg

pdf page 19 is the index to all wiring
look there, and tell that it is. i cant guess it.

the GDM model and VIC are 2 options.
graphic display module. ive no clue as to yours.
gdm lamps can be changed
the VIC veh. info, center, display


see intruments chapter and read all that.
more here

https://sites.google.com/site/thezjpage/the-electronic-vehicle-information-center-evic-and-graphic-display-module-gdm

see that list, name one thing that dont work?
and we can run that.

Hope this helps:- Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm.
Cavity/Fuse Diagram (1996 Grand Cherokee, passenger side kick plate to find, Owner's Manual pgs 205-206): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Row 1: 1-6 (left to right) Row 2: 7-12 Row 3: 13-18 Row 4: 19-22
1996 Jeep Grand Cherokee Fuse Panel (Passenger Side kick panel) Reply

CAVITY FUSE DESCRIPTION 1 -10 amp (RED) Radio 2 -15 amp (Lt Blue) Cigarette Lighter 3 -10 amp (RED) Rear Washer Switch, Body Controller 4 -10 amp (RED) Airbag 5 -10 amp (RED) Lamp Out Module, Overdrive Switch, OBD II 6 -15 amp (Lt Blue) Vehicle Information Center/Graphic Display Module Park & Side Lamps, Overhead Console Lighted Visor, Automatic Dimming Mirror 7 -20 amp (Yellow) Body Amp, Cluster, Body Controller 8 -20 amp (Yellow) Rear Wiper Motor, Flipper Glass Solenoid, Cargo Lamp, Trailer Tow 9 -15 amp (Lt Blue) Brake Switch 10- 10 amp (RED) Rear Window Defroster 11 -10 amp (RED) ABS Module 12 -10 amp (RED) Heater-Ventilation-A/C Control & Recirculation Motor 13 -15 amp (Lt Blue) Hazard Switch, Turn Signal Switch 14 -15 amp (Lt Blue) Spare 15 -15 amp (Lt Blue) Spare 16 -10 amp (RED) Right & Left Courtesy Lamp, Glove Box Lamp, Halo Lamp Cargo Lamp, Underhood Lamp, Dome/Read Lamp Right & Left Visor, Automatic Dimming Mirror 17 -15 amp (Lt Blue) Radio Illumination, Tail Lamp, Graphic Display Module, Park & Side Lamps, Headlamp Switch, Body Controller 18 -20 amp (Yellow) Spare 19 -15 amp (Lt Blue) Passing Light 20 -15 amp (Lt Blue) Radio, Heater-Ventilation-A/C, Vehicle Information Center 21 -15 amp (Lt Blue) Power Outlet 22 -10 amp (Blue) Airbag Module -------------------------------------------------------------------------------------
1996 Jeep Grand Cherokee Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Pink/Black Ignition Switch Harness Starter Yellow Ignition Switch Harness Ignition Dark Blue/Gray Ignition Switch Harness Ignition 2 Red/Black Ignition Switch Harness (for AC) Accessory Black/Orange Ignition Switch Harness Tach Gray/White Coil Brake Switch White/Tan Brake Switch Trunk Pin n/a Works with Dome Light Parking Lights Blue/Red (+) Left of Steering Column or Light Switch Head Lamp Tan/Black Light Switch Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM -slice into this wire, & wire it to ground, this disables the alarm. Door Trigger Yellow (-) Driver's Kick Panel see notes Door Lock 5/Wire in Driver's Inside Driver's Door Orange/Purple Lock Pink/Black Unlock Door Unlock and Passenger's Doors Inside Passenger's Door Black/White L Pink/Black Unlock Horn Wire Gray/Orange (-) Steering Column Windows Up LF=Light Blue, RF=Brown/White, LR=Blue/White, RR=Gray/Black Doors Windows Down LF=White, RF=Purple/White, LR=Red/Black, RR=Green/White
• Cruise Control Information • Stereo Information • View all Jeep Vehicles

Hope this helps:
Cavity/Fuse Diagram (1996 Grand Cherokee, passenger side kick plate to find, Owner's Manual pgs 205-206): 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22

Row 1: 1-6 (left to right) Row 2: 7-12 Row 3: 13-18 Row 4: 19-22
1996 Jeep Grand Cherokee Fuse Panel (Passenger Side kick panel) Reply

CAVITY FUSE DESCRIPTION 1 -10 amp (RED) Radio 2 -15 amp (Lt Blue) Cigarette Lighter 3 -10 amp (RED) Rear Washer Switch, Body Controller 4 -10 amp (RED) Airbag 5 -10 amp (RED) Lamp Out Module, Overdrive Switch, OBD II 6 -15 amp (Lt Blue) Vehicle Information Center/Graphic Display Module Park & Side Lamps, Overhead Console Lighted Visor, Automatic Dimming Mirror 7 -20 amp (Yellow) Body Amp, Cluster, Body Controller 8 -20 amp (Yellow) Rear Wiper Motor, Flipper Glass Solenoid, Cargo Lamp, Trailer Tow 9 -15 amp (Lt Blue) Brake Switch 10- 10 amp (RED) Rear Window Defroster 11 -10 amp (RED) ABS Module 12 -10 amp (RED) Heater-Ventilation-A/C Control & Recirculation Motor 13 -15 amp (Lt Blue) Hazard Switch, Turn Signal Switch 14 -15 amp (Lt Blue) Spare 15 -15 amp (Lt Blue) Spare 16 -10 amp (RED) Right & Left Courtesy Lamp, Glove Box Lamp, Halo Lamp Cargo Lamp, Underhood Lamp, Dome/Read Lamp Right & Left Visor, Automatic Dimming Mirror 17 -15 amp (Lt Blue) Radio Illumination, Tail Lamp, Graphic Display Module, Park & Side Lamps, Headlamp Switch, Body Controller 18 -20 amp (Yellow) Spare 19 -15 amp (Lt Blue) Passing Light 20 -15 amp (Lt Blue) Radio, Heater-Ventilation-A/C, Vehicle Information Center 21 -15 amp (Lt Blue) Power Outlet 22 -10 amp (Blue) Airbag Module -------------------------------------------------------------------------------------
1996 Jeep Grand Cherokee Alarm, Remote Starter, Keyless Entry Wiring Information Constant 12V+ Pink/Black Ignition Switch Harness Starter Yellow Ignition Switch Harness Ignition Dark Blue/Gray Ignition Switch Harness Ignition 2 Red/Black Ignition Switch Harness (for AC) Accessory Black/Orange Ignition Switch Harness Tach Gray/White Coil Brake Switch White/Tan Brake Switch Trunk Pin n/a Works with Dome Light Parking Lights Blue/Red (+) Left of Steering Column or Light Switch Head Lamp Tan/Black Light Switch Factory Disarm Purple/Yellow (-) Driver's Kick Panel Black Connector at ECM Door Trigger Yellow (-) Driver's Kick Panel see notes Door Lock 5/Wire in Driver's Inside Driver's Door Orange/Purple Lock Pink/Black Unlock Door Unlock and Passenger's Doors Inside Passenger's Door Black/White L Pink/Black Unlock Horn Wire Gray/Orange (-) Steering Column Windows Up LF=Light Blue, RF=Brown/White, LR=Blue/White, RR=Gray/Black Doors Windows Down LF=White, RF=Purple/White, LR=Red/Black, RR=Green/White
• Cruise Control Information • Stereo Information • View all Jeep Vehicles

The 1996 Jeep Grand Cherokee Laredo Anti-Theft System is equipped with Vehicle Theft Security System (VTSS). VTSS system monitors vehicle doors, hood, liftgate and ignition. If an attempt is made to enter or operate vehicle without proper disarming of system, vehicle horn will sound, headlights, taillights and parking lights will flash, and engine will be prevented from running.

The following wiring diagram and electronics circuit contains detail schematics of The 1996 Jeep Grand Cherokee Laredo Anti-Theft System. Herein you will find interconnection between electronics parts of the system such as body control module, auto headlamp light sensor. VTSS led, driver door module, passenger door module, cylinder lock switch, junction block, power distribution center, and grounding. Herein you will learn also how the Vehicle Theft Security System works, removal, installation, testing and troubleshooting procedures.

Try HERE.

Also, remember that here can find the Jeep Grand Cherokee Service & Repair Manual.
Hope help with this.

You need first remove jack screw attaching top of headlamp mounting module.
Grasp upper inboard and lower outboard corners of headlamp and forcefully pull headlamp outward.
Remove bulbs sockets and separate headlamp from vehicle.

Also, I suggest chek your Jeep WJ REpair Manual Section-08L-Lamps-Ewj8l for more details and graphics.

Hope helps with this. Good luck (remember rated this help)

Remove 4 screws from bottom of lens; lift lens off from bottom.
Pull trip reset knob off and remove mask by liftng from bottom. Mask is snapped in along the top.

Also, can fin more details and graphics in the ZJ-Secc-8E-Instrument-Cluster-and-Gauges

I hope helps with this (remember rated this help) Good luck.

Throttle position sensor

If you refer to the display that shows a diagram of the vehicle with the wheels lit. That display might have turned off due to a fuse problem. Chek the fuse. If the fuse is ok and the cabling powering the module are ok, then the module itself might be the problem. If that was the case, before thinking of purchasing a new one, disinstall the bad one, open it (8 small philips screws), replace the four capacitors it has on the back of the circuit board of the module (use soldering iron proper procedures), (each capacitor might cost 50 cents while the whole module might cost more than 100 dollars), and reassemble. That should take care of it for many years ahead.