Question about 2008 Dodge Grand Caravan

1 Answer

How do you remove driver airbag on 2008 dodge

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 215 Answers

First thing you do is disconnect the negative cable from the battery.remove the three bolts behind streeging wheel,then pull it out and disconnect the air bag.

Posted on Dec 27, 2010

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Airbag ligth dodge grand caravan 2007


You cannot remove it unless you replace the airbag. I have the same thing on my drivers airbag. You will still pass inspection with the drivers airbag not working. To get the airbag replace, you are looking at about 3 grand, I just put a dark sticker over my airbag deployed light because I got tired of looking at it The airbag will not cause other problems for you. Just cover up the light and forget about it.

Oct 16, 2017 | Dodge Cars & Trucks

Tip

Drivers airbag removal / horn switch removal 1998 dodge neon


I have a 98 dodge neon and the horn was stuck on all the time. I could not find anyone who could tell me how to remove the cover on the airbag so I could get to the horn touchpad. this is what i did.
first unhook the battery.
remove the 2 screws on the cruise control buttons on each side of the steering wheel.
remove the bolt(s) from both sides of the airbag bracket
unplug the horn wire
unplug the airbag wire CAREFULLY (it's the one in the center).( I left this hooked up)
I did not need to completely remove the air bag from my car, because my horn was stuck on and I just needed to remove the cover.
after I removed the airbag assembly I removed all the screws holding the cover on I removed the inner touch pad so I could fix it.
I reversed the steps to put it back together.. the horn works as it should.

on Jul 26, 2015 | 1998 Dodge Neon

1 Answer

Dodge caliber passenger side air bag removal


take clove box out first un hook batt. un plug airbag it well unbolt

Mar 07, 2015 | 2008 Dodge Caliber

1 Answer

How to rem ove and install climate control panel 2008 dodge ram 3500


2008 dodge or ram truck ram 3500 truck 2wd l6-6.7l dsl turbo








  • a/c heater control - removal



removal



warning: disable the airbag system before attempting any steering wheel, steering column, or instrument panel component diagnosis or service. disconnect and isolate the battery negative (ground) cable, then wait two minutes for the airbag system capacitor to discharge before performing further diagnosis or service. this is the only sure way to disable the airbag system. failure to take the proper precautions could result in an accidental airbag deployment and possible personal injury or death.






131139774












note: single zone a/c-heater control shown. dual zone similar.





  1. disconnect and isolate the negative battery cable.


  2. remove the center bezel (1) from the instrument panel and disconnect the wire harness connectors (4 and 5) from the back of the a/c-heater control (2) see: body and frameinterior moulding / trimdashboard / instrument panelservice and repairinstrument panel center bezel - removal .



note: take the proper precautions to protect the front face of the center bezel from cosmetic damage.




  1. place the center bezel on a workbench and remove the four screws (3) that secure the a/c-heater control to the center bezel and remove the control.


install------->>>>

installation




131139774












note: single zone a/c-heater control shown. dual zone similar.





  1. position the a/c-heater control (2) into the back of the instrument panel center bezel (1).


  2. install the four screws (3) that secure the a/c-heater control to the center bezel. tighten the screws to 2.2 nm (20 in. lbs.).


  3. connect the wire harness connectors (4 and 5) to the back of the a/c-heater control and install the instrument panel center bezel see: body and frameinterior moulding / trimdashboard / instrument panelservice and repairinstrument panel center bezel - installation .


  4. reconnect the negative battery cable.


assuming this is the correct application for your vehicle, you should be good to go. let me know if you need further assistance.

-tim

autoecu1

800-921-9060

Jan 21, 2015 | Dodge Cars & Trucks

1 Answer

How to remove air bag from 2008 dodge grand caravan


There screws located in the back of the steering wheel. Look for round circles in the plastic these pop out to gain access. When these screws are removed the whole middle of the steering WHEEL lifts out. Word OF EXTREME CAUTION !!!!!!!!! The wiring has to be removed correctly because airbags are AIRBAGS ARE LOADED AND CAN EXPLODE AND BLOW UP IN YOUR FACE AND KILL OR SEVERELY INJURE OR BURN YOU. DON'T DO THIS UNLESS YOU ABSOLUTELY SURE OF WHAT YOUR DOING.

Mar 02, 2014 | Dodge Grand Caravan Cars & Trucks

1 Answer

2008 Dodge Avenger Airbag light stays on


i got a 2011 dodge avenger the airbag warning light stay on , can u someone give me an idea how to fix it please?

Dec 13, 2011 | 2008 Dodge Avenger

1 Answer

I want to replace the right hand speed control for the cruise control on my 2008 Chrysler Aspen - any ideas? Anyone!


11_18_2011_12_24_34_am.gif
REPLACING CRUISE CONTROL SWITCH

1.
Disconnect and isolate negative battery cable from battery.

2. Remove airbag module (See AIRBAG REMOVAL below).

3. Remove speed control switch mounting screw and remove switch from steering wheel.

4. Reverse procedure to install.
AIRBAG REMOVAL
1. Disconnect and isolate negative battery cable from battery.

2. From the underside of the steering wheel, remove the two screws that secure the driver airbag to the steering wheel armature.
CAUTION: The horn switch and the clockspring pigtails connected to the back of the airbag module are fragile. Do not pull on these wires to disengage them. These must be handled carefully to prevent damage to the horn switch and/or the clockspring assembly.
3. Pull the driver airbag away from the steering wheel enough to access the three electrical connections on the back of the airbag housing.

4. Disconnect the steering wheel wire harness connector for the horn switch from the horn switch feed pigtail wire connector, which is located on the back of the driver airbag housing.

5. The clockspring driver airbag pigtail wire connectors are secured by integral latches to the airbag inflator connector receptacles, which are located on the back of the driver airbag housing. Depress the latches on each side of the connector insulator and pull the insulators straight out from the airbag inflator to disconnect them from the receptacles.

6. Remove the driver airbag from the steering wheel.

7. Reverse procedure to install.

Nov 17, 2011 | Cars & Trucks

1 Answer

Where is the airbag turnoff switch in a 2008 Dodge Dakota crew cab pickup?


usually on the dash between the passenger and driver that is if your vehicle has one check your manual or ask a chrysler dealer

Dec 15, 2009 | 2008 Dodge Dakota

1 Answer

Removal of 2008 Prius steering wheel -


with a small flat screwdriver, remove the 2 by 2 inch black plastic covers behind the steering wheel. one of them has a hole for the cruis control lever.
loosen but dont remove the two torx screws behind these covers.
allow the airbag to fall out into your hands.
carefully raise the two yellow retainers on the airbag wires, then pull the wires away from the airbag module.
then squeeze and pull the black horn wire from the airbag.
to replace the steering wheel, unplug all the wires you see and remove the 19mm nut holding the wheel.
then by hand wiggle the steering wheel toward you.

Mar 24, 2009 | 2008 Toyota Prius

Not finding what you are looking for?
2008 Dodge Grand Caravan Logo

345 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...