Ever since i replaced the wiper motor on 2003 chevy impala the wipers stop in up position instead of down position when stop- ped on delay position.is it something i did wrong when replac- ing the motor?does the motor need to be in certain position when reconnecting the linkage & the wiper arms?also heard something about an electrical board may be bad?but they worked fine until i replaced wiper motor.

Possible wiper linkage has broken/seperated from wiper motor. The wiper cowling covering the linkage assembly will need to be removed to inspect/repair

Replace the wiper motor. The module is built into it. And it has lost it's park position.

Most likely a little circuit board that controls the wiper delay, or the wiper switch itself has gone bad and has an intermittent break.

Replace the wiper motor. It is under the wiper blades. remove the blade arms, remove the plastic bezel, remove the motor. The motor has the delay and speeds built in it.

The wiper motor is what holds the module. So to fix it, you have to replace the motor. Remove the wiper arms. Remove the cover, there may be a few screws to take out. Pry the control arm of the motor. Remove the bolts holding the motor. Then put the new on in.

Sorry , no adjustment .
Wiper/Washer System Components
The Wiper / Washer System consists of the following components:
• Windshield wiper / washer switch
• Windshield wiper system module / motor
• Windshield washer fluid pump
• Windshield washer fluid level switch
• WPR 25A fuse
Wiper / Washer System Operation
The windshield wiper motor module is part of the windshield wiper motor cover and controls the wiper motor operation. The windshield wiper motor is a 2 speed motor. Windshield wiper DELAY operation is a low speed wiper motor function with a variable delay interval between the wipe cycles. The DELAY interval is controlled through a series of resistors within the wiper / washer switch.
Park Position Operation
When the windshield wiper / washer switch is turned to the OFF position while the wiper motor is somewhere in mid-cycle, the wiper motor module will continue to operate the wiper motor until the wipers reach the park position. If the ignition is turned off while the wipers are in mid-cycle, the wipers will stop immediately where they are. The wipers will park the next time the ignition is cycled to the ON position.

Do you know how to do diagnostic's ?

Wipers Blades Do Not Park
Step
Action
Yes
No
Schematic Reference: Wiper/Washer Schematics
Connector End View Reference: Wiper/Washer Connector End Views
DEFINITION: This table diagnoses the wipers operate normally but will not return to the park position when the wiper operation is cancelled.
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Turn ON the ignition, with the engine OFF.
Move the wiper switch to the LO position.
Move the wiper switch to the OFF position.
Do the front wipers advance to the park position?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 3
3
Turn the ignition switch to the RUN position.
Turn the wiper switch to OFF.
Disconnect the wiper/washer switch connector.
Do the wipers park?
YES - Go to Step 7
NO - Go to Step 4
4
At the wiper/washer switch connector, measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 5
NO - Go to Step 8
5
Reconnect the wiper/washer switch connector.
Disconnect the wiper motor connector.
Measure the voltage of the windshield wiper switch signal 2 circuit.
Does the voltage measure greater than 1.0 volts?
YES - Go to Step 6
NO - Go to Step 8
6
Repair a short to battery positive voltage in the windshield wiper switch signal 2 circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
YES - Did you find and correct the condition?
NO - Go to Step 9
--
7
Replace the wiper/washer switch. Refer to Turn Signal Multifunction Switch Replacement in Steering Wheel and Column - Tilt.
YES - Did you complete the replacement?
NO - Go to Step 9
--
8
Replace the wiper motor cover. Refer to Wiper Motor Cover Replacement .
YES - Did you complete the replacement?
NO - Go to Step 9
--
9
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Usually the park switch inside the wiper motor is the fault.

Your windshield arm is in need of repositioning. Take off the cap on the windshield arm and loosen the nut under the cap. Reposition the arm so that it faces 180 degrees flat to the passenger side of the car. Tighten the nut. This should solve the problem you've described.

Your wiper motor has shorted out and needs replacment.
In order to find out you need to disconnect the wiring from the wiper control switch,with the ignition on, if the wipers stop then you need to replace the switch.
If the wipers keep running, then you have a defective motor, replace the motor.

The problem could be a bent parking pall bracket. This is usually caused when you wipe snow from windshield using the wipers instead of brushing off. You need to remove both wipers and the cover from the drivers side. Remove the cover over the wiper motor assembly (held by a plastic button). On the right side of the wiper mechanism is a small tab (part of the wiper bracket). This tab needs to be straight for the wiper park pall to rest against.Carefully hammer this tab straight (or you may have to replace bracket, big job) Then cycle the wiper and you will see the assembly return to park position. Re-install all parts in reverse order.
Hope this works for you.