Question about Dodge Intrepid

4 Answers

Need diagram to replace timing belt on 2000 dodge intrepid 3.5 engine

Posted by on

Ad

4 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,596 Answers

I Show Only a 3.2L For this Year this Will Guide you Enjoy your Work RejakWilson


REMOVAL

CAUTION: The following procedure can only be used when the camshaft sprockets HAVE NOT BEEN LOOSENED or removed from the camshafts. Refer to Camshaft Gear/Sprocket and Timing Components, if sprocket(s) or camshaft(s) have been loosened or removed.

CAUTION: The 3.2/3.5L are NOT freewheeling engines. Therefore, care should be taken not to rotate the camshafts or crankshaft with the timing belt removed.

  1. Disconnect negative cable from remote jumper terminal.
  2. Remove upper radiator crossmember.
  3. Disconnect fan module electrical connector.
  4. Remove cooling fan module and accessory drive belts.
  5. Remove crankshaft damper and front timing belt covers.
  6. Mark belt running direction, if timing belt is to be reused.
CAUTION: When aligning timing marks, always rotate engine by turning the crankshaft. Failure to do so will result in valve and/or piston damage.

need diagram to replace timing - f90f2f1.gif Fig. 94

  1. Rotate engine clockwise until crankshaft mark aligns with the TDC mark on oil pump housing and the camshaft sprocket timing marks are between the marks on the rear covers (Fig. 94).
CAUTION: Align the camshaft sprockets between the marks on rear belt covers before timing belt removal or damage to valve and/or pistons could occur.

  1. Using a ink or paint marker; mark the exact position of the camshaft sprocket timing mark relative to the two timing marks on the rear timing cover.
NOTE: When timing belt tensioner is removed from engine, always store in the vertical (plunger facing upward) position

09766f9.gif Fig. 95

  1. Remove the timing belt tensioner (Fig. 95) and remove timing belt.
TIMING BELT TENSIONER

  1. When tensioner is removed from the engine it is necessary to compress the plunger into the tensioner body.
CAUTION: Compress the tensioner slowly, as damage to tensioner couldneed diagram to replace timing - c719a3d.gif />
c719a3d.gif Fig. 96

  1. Place the tensioner into a vise and SLOWLY compress the plunger (Fig. 96). Total bleed down of tensioner should take about 5 minutes.
CAUTION: Index the tensioner in the vise the same way it is installed on the engine. This is to ensure proper pin orientation when tensioner is installed on the engine.

  1. When plunger is compressed into the tensioner body install a pin through the body and plunger to retain plunger in place until tensioner is installed.
NOTE: When timing belt tensioner is removed from engine, always store in the vertical (plunger facing upward) position.

INSTALLATION

CAUTION: This procedure can only be used when the camshaft sprockets HAVE NOT BEEN LOOSENED or removed from the camshafts.

CAUTION: If camshafts have moved from the timing marks, always rotate camshaft towards the direction nearest to the timing marks (DO NOT TURN CAMSHAFTS A FULL REVOLUTION OR DAMAGneed diagram to replace timing - a7cd673.gif and/or pistons could result).

a7cd673.gif
Fig. 97

  1. Align the crankshaft sprocket with the TDC mark on oil pump cover (Fig. 97).
  2. Align the camshaft sprockets (to reference mark made upon removal) between the marks on the rear covers (Fig. 94).
  3. Install the timing belt starting at the crankshaft sprocket going in a counterclockwise direction (Fig. 97). Install the belt around the last sprocket. Maintain tension on the belt as it is positioned around the tensioner pulley.
  4. Holding the tensioner pulley against the belt, Install the tensioner into the housing and tighten to 28 Nm (250 in. lbs.) . Each camshaft sprocket mark should still fall between the cover marks.
  5. When tensioner is in place pull retaining pin to allow the tensioner to extend to the pulley bracket.
  6. Rotate crankshaft sprocket 2 revolutions and check the timing marks on the camshafts and crankshaft. The marks should line up within their respective locations (Fig. 97). If marks do not line up, repeat procedure.
  7. Install timing belt covers and crankshaft damper.
  8. Install accessory drive belts and cooling fan module.
  9. Install upper radiator crossmember.
  10. Connect negative cable to remote jumper terminal.
  11. Start engine and allow to idle for approximately 1 minute. If a noise is present from the timing belt/tensioner, air has possibly entered the tensioner.
    1. To remove air from tensioner; using a DRB III, operate the engine at speed of 1600-2000 RPM for 10 minutes. This will purge air from tensioner.
NOTE: If air is present, the timing belt tensioner will be soft and may generate noise. This noise should disappear after no more than 15 minutes of engine running time.

Posted on Oct 21, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,565 Answers

Go to autozone.com, there is a complete tutorial on timing belt replacement. just log in and go to repair guide

Posted on Oct 21, 2010

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Hi cd 20 engine generator timing belt installation?

Posted on Apr 18, 2014

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Dodge Master
  • 1,871 Answers

Hello! Here is requested diagram...The 3.5L engine is not free wheeling, Care must be taken not to move the camshafts and crankshaft with the belt removed...Rotate engine by turning the crankshaft...Failure to do so will result in valve and piston damage...

Guru..................Saailer
need diagram to replace timing - ac06b83.gif

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Posted on Oct 21, 2010

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

philw1964200

Phil Whisenant

  • 163 Answers

SOURCE: need a 3.5 engine mounting

Google 1997 Dodge 3.5 liter Engine Mounting Diagram. Same for the 2002 engine. I guarrantee you will find it.For some strange reason you would'nt call your local Dodge dealer and ask them where you can go to on the web and locate it.

I’m happy to help further over the phone at https://www.6ya.com/expert/phillip_293d34ebcf028794

Posted on Jan 06, 2009

BCAS1298

Alexander Mimun

  • 3092 Answers

SOURCE: is there a diagram for replacing a alternator belt

You did't say what size engine, so here's for 2.7L, 3.2L and 3.5L.


3991859.gifdf78fcb.gif

Posted on Jul 02, 2010

hotrodshop

Brian Franklin

  • 106 Answers

SOURCE: I'm replacing timing belt and

Here is a few diagrams of the timing marks. Be sure that you check the marks after the tensioner has been installed as well because installing the tensioner tends to slightly re-adjust the positions of the cams as it takes up slack on one side.

Be carful when turning the engine (by hand) because these engines are an interferance engine and the valves can contact the pistons. After everything is installed and tight, rotate the engine by hand twice and then recheck that the marks are good to go.

If you haven't replaced the water pump, I highly recommend you do it now.


hotrodshop_1.gifhotrodshop_2.gif

Posted on Apr 24, 2011

Anonymous

  • 27 Answers

SOURCE: Serpentine/drive belt routing diagram of a 2002 dodge Intrepid needed.

check dodge website you have to register to get the owners manual which has or if you have your owners manual

Posted on May 29, 2009

Anonymous

  • 1 Answer

SOURCE: timing belt diagram replacement for a 2000 dodge

Go to alldata diy or a parts house that has a gates book.

Posted on Mar 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a2000 dodge intrepid 2.7 do I have a chain or belt


My info says you have a timing chain. You do have a drive belt for accessories.

Feb 28, 2015 | 2000 Dodge Intrepid

1 Answer

Belt diagram for 2.7


here is a diagram www.google.com belt diagram for 2.7 2000 Dodge Intrepid

Jun 29, 2012 | 2000 Dodge Intrepid

1 Answer

Is there a diagram for replacing a alternator belt on a 2000 dodge intrepid


You did't say what size engine, so here's for 2.7L, 3.2L and 3.5L.


3991859.gifdf78fcb.gif

Jul 02, 2010 | 2000 Dodge Intrepid

1 Answer

What is the timing diagram for a 2000 dodge intrepid 2.7 litre engine


Trying to time this 2000 intrepid 3.5L after puting water pump in i line the timeing mark But when i put the tensioner back on it throws the mark off

Jun 15, 2010 | 2000 Dodge Intrepid

1 Answer

Timing belt diagram replacement for a 2000 dodge intrepid 3.2


Go to alldata diy or a parts house that has a gates book.

Mar 15, 2010 | 1999 Dodge Intrepid

2 Answers

Just need timing belt diagram 2002 dodge intrepid 2.7 liter. I changed my plugs, car turns over starts for a minute makes loud sound in the engine, kind of back fires


your intrepid doesnt have a timing belt it has a chain. there are major problems with these engines, theres a big one with the chain jumping due to a tensioner breaking or a guide,heres a diagram for the chain setup.this is a very important setup make sure you use correct sprokets in the right place and also if it jumped timing il bet you may have some bent valves,1441a70.gif

Jan 24, 2010 | 2002 Dodge Intrepid

2 Answers

Where is the camshaft position sensor located on a 2000 Dodge Intrepid?


If it is a 3.5 it is located on the front of the engine on the drivers side under the plenum.

Oct 23, 2009 | 2000 Dodge Intrepid

2 Answers

How to put belts on a 2000 Dodge Intrepid, 2 front belts have worn out.


Belt is pretty simple to replace here is a diagram for you car's belt. contact me if you need more help. If I fixed ya LEAVE ME A FIX-YA comment. http://www.2carpros.com/car_repair_information/tec_info/2000/dodge/intrepid/2000_dodge_intrepid_drive_belt_routing_diagram.htm

Dec 27, 2008 | 1999 Dodge Intrepid

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

8,916 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...