Programing a keyless remote I do not have any remotes other than the one I would like to program it is for a 2002 dodge dakota quad cab

Hi,

Read the complete procedure :-

Keyless Entry - Programming Procedure
Notes

NUMBER: 08-007-02

GROUP: Electrical

DATE: Mar. 25, 2002

SUBJECT:
Remote Keyless Entry (RKE) Programming Procedures

MODELS:

1999 - 2002 (AB) Ram Van/Wagon

1999 - 2002 (AN) Dakota

1999 - 2002 (BR/BE) Ram Pickup

1999 - 2002 (DN) Durango

2002 (DR) Ram Pickup

2001 - 2002 (JR) Sebring Sedan/Stratus Sedan/Sebring Convertible

2002 (KJ) Liberty

1999 - 2002 (LH) Concorde/Intrepid/LHS/300M

1999 - 2000 (NS) Town & Country/Caravan/Voyager

1999 - 2002 (PL) Neon

1999 - 2002 (PR) Prowler

2001 - 2002 (PT) PT Cruiser

2001 - 2002 (RS) Town & Country/Caravan/Voyager

1999 - 2002 (WJ) Grand Cherokee

1999 - 2001 (XJ) Cherokee

DISCUSSION:







A Remote keyless Entry (RKE) Programming Procedures Card (Publication No. 81-170-00011) is being provided with this Technical Service Bulletin to simplify RKE transmitter programming on 1999 - 2002 North American vehicles. Additional copies of the RKE publication, 81-170-00011 (Fig. 1), can be ordered from DDS Distribution Services, LTD. Their number is 1-800-890-4038.

NOTE :THE RECENTLY RELEASED MILLER SPECIAL TOOL, "RF DETECTOR NO. 9001", SHOULD BE USED TO DETERMINE IF THE TRANSMITTER IS WORKING BEFORE BEGINNING PROGRAMMING PROCEDURES. THE RF DETECTOR INDICATES IF THE TRANSMITTER IS WORKING, NOT IF IT IS PROGRAMMED TO A VEHICLE.

DaimlerChrysler North American Remote Keyless Entry Programming Procedures

NOTE :PLEASE READ INSTRUCTIONS FULLY BEFORE ATTEMPTING TO PROGRAM TRANSMITTERS.

Program Method A (Customer Program Method)

1. Press (LOCK) button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.

2. Turn ignition to run position. (Allow ignition chimes to stop).

3. Using any original (working) transmitter, press the [UNLOCK] button for 4 to 10 seconds.

4. Within the specified 4 to 10 seconds, continue pressing the [UNLOCK] button and press the [PANIC] button for 1 second and release both buttons (AN/DN release either button first). A chime will sound to indicate that the transmitter programming mode has been entered (allow 3 seconds for chime to sound).

5. Press [LOCK] and [UNLOCK] buttons simultaneously for 1 second and release (a short chime will sound for AN/DN).

6. Press and release any button on the same transmitter and a chime will sound after successfully programming the transmitter (locks will cycle for AN/DN).

NOTE :(FOR DR ONLY) A CHIME WILL NOT SOUND ON STEP # 6 FOR THE FIRST TRANSMITTER PROGRAMMED, BUT WILL SOUND UPON PROGRAMMING THE SECOND TRANSMITTER.

7. Repeat steps 5 through 6 to program additional transmitters.

8. Turn ignition to OFF position. Transmitter programming mode v/ill discontinue after 60 seconds (30 seconds for AN/DN and RS). (All transmitter programming must be completed within time specified).


Program Method B (Customer Program Method)

1. Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.

2. Turn ignition to the run position (Allow ignition chimes to stop).

3. Using original transmitter, press and hold the [UNLOCK] button on the transmitter for between 4 and 10 seconds.

4. Continue to hold the [UNLOCK] button and press the [PANIC] button. A chime will sound to indicate that the transmitter programming mode has been entered (Allow 3 seconds for chime to sound).

5. Press a button on all transmitters to be programmed into the system including any previously programmed transmitters; a chime will sound when each transmitter has been programmed.

6. Turn the ignition to OFF position to exit the transmitter programming mode.


Program Method C (Dealer Program Method) *Can be used for any type transmitter.

1. Press [LOCK] button 5 times at 2 second intervals to resynchronize transmitter. Attempt to function transmitter, if working as designed discontinue programming.

2. Turn ignition to the run position (Allow ignition chimes to stop).

3. Plug DRBIII to vehicle's 1-way data link connector.

4. Follow Service Manual and DRBIII instructions to program transmitters.


Program Method D (For use with AB vehicles not equipped with VTSS only)

1. Locate the dark green program enable wire connected to pin # 1 of the 16-way data link connector under the left side of the instrument panel.

2. Connect the program enable wire terminal to a good ground.

3. Insert the key into the ignition and turn the ignition switch to the ON position. The power locks will cycle (Lock and Unlock) indicating that program mode has been entered.

4. Using the transmitter to be programmed, press either [LOCK] or [UNLOCK]. The power locks will cycle indicating the transmitter has been programmed successfully.

5. Repeat step 4 to program additional transmitter.

6. Disconnect the program enable wire from ground to exit program mode.

7. Turn the ignition to the OFF position and remove the key.

NOTE :REFER TO DAIMLERCHRYSLER MDS2 SYSTEM OR PARTS DEPARTMENT TO OBTAIN THE CORRECT PART NUMBER AND REVISION FOR SPECIFIED VEHICLE.

POLICY:
Information Only

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Unfortunately, nobody who answered bothered to read your question properly. Rather than insult anybody's intelligence (which would not be too difficult considering the answers) I will go ahead and tell you what you need to know. The simple answer is without a working remote, a dodge vehicle with keyless remote entry (KRE) can NOT be put into programming mode unless you have a working remote or you happen to have a dodge only scanner called a wiTech tool. This uses a Chrysler developed protocol called DRB III to access the non ODB II functions that are Dodge specific and to effect programming od the ECU/EEC. Thats it. One or the other. A working remote or the tool. There is simply no other way to program Chrysler/Dodge remotes. The tool goes for around 2500 bucks used. Your best bet is to go to a local dealer. Sometimes if they are benevolent or you have a service relationship with them they will do it for no charge. Otherwise a typical cost to program a remote is around 50 dollars. Once you have a working remote then you can program spares with your working remote.

This forum has the answer you're looking for: http://www.dodgedakota.net/boards/dea/373.html Sometimes you have to order a new remote from the distribution service or car dealership. Hopefully the forum can answer your question so you won't have to buy a new one. http://www.centurylogistics.ca/distribution.html