Can't get the new serpentine belt on my 2003 town car

you should use internet to look this u pas well any info too, lees than 5 seconds.


https://www.justanswer.com/ford-lincoln/56d86-2000-lincoln-town-car-serpentine-belt-sedan-diagram-the-hood.html

you may omit the compressor with a shorter belt of you can find one. just make sure the rest of the pulleys are working especially the water pump and power steering.

Install new belt only on driverside of engine. 55 1/4" belt with 6 groves....slide on to water pump pulley last its kinda tight..

Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.

3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.

4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.

5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.

6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

Any bearing mounted pulley can "freeze" if a bearing wears out. The most common result it it can burn up a belt which will break with the engine running. When it snaps it MIGHT damage anything it hits - usually with no bad results. ANY bad pulley (or pulley driven part such as the alternator) needs to be replaced before a new belt is installed or the new belt will be damaged from the friction. To replace the serpentine belt - there should be a belt routing decal on the underside of the hood or on the shroud covering the radiator.

From the Dayco web site:

hi,
sir i was not able to get you the exact full sized picture for but this will help you.......since 1992 model it is not available in net....]

http://images.google.co.in/images?hl=en&q=serpentine%20belt%20diagram%201992%20lincoln%20town&um=1&ie=UTF-8&sa=N&tab=wi


you cant enlarge the image because it is removed

Your question is prety vague, but I suspect what you are asking is "how do i change the belt on a 1997 Lincoln Town Car?"

If that's what you were asking for, this link will take you to a "how to" video for changing the serpentine belt.
http://www.wonderhowto.com/how-to/video/how-to-change-a-serpentine-belt-on-your-car-39904/

try these websites drive belt diagram www.webcrawler.com and www.alldatadiy.com and for the most part there shoulld be a diagram under your hood showing you how to put the new belt on.

There's a diagram at this link.