I did a check engine light test at auto zone and know have a list of 6 trouble codes they are as follows p0705, p0741, p0342, p0341, p0700 and p 0499 anyone please help me

The codes signify issue with the same component.

P0341 What the P0341 code means. P0341 is an OBD-II generic code that says the engine control module (ECM) detected the engine camshaft position sensor circuit is not within specifications. The sensor pulses do not correlate to the pulses of the crankshaft sensor.

P0341 OBD-II Trouble Code: Camshaft Position Sensor Circuit ...

P0342 Code: Camshaft Position Sensor "A" Circuit Low

https://www.carparts.com > blog > p0342-code-camshaf...
Dec 15, 2021 - P0342 is a diagnostic trouble code (DTC) that stands for "Camshaft Position Sensor 'A' Circuit Low." It basically means that your PCM is not ...

that will not work u need MBXA no sensors will work or the
trans will not shift

Here's a link to your code. P0741 OBD II Trouble Code

P0700

The transmission of a vehicle which has suffered a transmission problem will send the P0700 code to the vehicle engine control module (ECM)

P0705 Transmission Range Sensor Circuit Malfunction

Possible causes

- Open or short park/neutral position switch circuit
- Poor park/neutral position switch circuit connection
- Misadjusted park/neutral position switch
- Park/neutral position switch may be faulty

P0455. A code p0455 most likely means one or more of the following has happened:

A loose or improperly affixed gas cap

A non-conforming gas cap (i.e. not factory/original brand)

Other leak or damaged piece in EVAP system

P1125 Accelerator Pedal Position (APP) System

P2125 Throttle/Pedal Position Sensor/Switch "E" Circuit

P2138 Throttle possition sensor

Hi, you can see a full list of Jeep DTCs here: http://jsautosource.com/factory-manuals/dtc-definitions/full-list-of-all-definitions-for-dodge-chrystler-jeep-dtc-codes/
Your engine light will probably return immediately after clearing the codes until the P0700 is rectified. The 705 indicates your range sensor is out of adjustment or broken. The range sensor is mounted to the side of the transmission where the cable attaches. It may be adjustable. Normally, when the range sensor fails, the starter will not turn, because the sensor provides the park/neutral safety interlock to ensure the transmission is not in gear. Also, the range sensor usually includes the backup light switch. I usually adjust the sensor by putting the transmission in reverse, turning the key on, loosening the switch, and rotating it until the backup lights come on. Please let me know if you have questions and thanks for using FixYa.

Hello: First things first. If your car has a v/6 engine (3.0 liter) then yes code P0341 applies. The code relates to the camshaft position performance. The sensor is easy to replace, it is on the drivers side at the front of the engine (front of the valve cover) the sensor has one electrical connector and one bolt holds it on. If you have the v/6 engine then after replacing the sensor you will have to have a scan tool to clear the code.

I do not have a code book or chart for your model car but all codes with 700 are pertaining to the transmission

go to autozone and get the codes. they will test for free.

Message Center Display
The following messages may be displayed on the message center.
This message center will display CHECK TRANSMISSION if the following codes have been set.


DTC Codes Possible Faults P1746, P1747, P1760 Electronic pressure control solenoid P0743, P1767 Torque converter clutch circuit P0750, P0755, P0760 Shift solenoid circuit P1714, P1715, P1716 ISIG P0731, P0732, P0733, P0734 SFT error P0741, P1742, P1743, P1744 Torque converter clutch error P1783 Over temperature P1700 NEV error P0712, P0713, P0710,
P1710, P1713, P1718 Transmission fluid
temperature error P0705, P0708, P1704 Transmission range sensor error P0500, P0503 Vehicle speed sensor error P0715 Turbine shaft speed error
NOTE: For codes. For additional information, refer to Diagnostic Trouble Code Chart.

the code for camshaft sensor is--p0341 and p0342, po341 is camshaft range or performance problem. p0342 is camshaft curcuit , low input. hope this helps carl.

p0341 on a scanner means something is wromg with the camshaft position sensor have it checked