There is a service bulletin on this. They have changed the spec, The new spec is 44ft lbs. Then an additional 95 degrees. Start from the center and work you way out
Torque to 44 ftlbs then an additonal 95 degrees start inside and work cross pattern out.
I need the Torque spec's for a 2001 Pontiac grand am se 3.4L motor I need both Heads and Manifold Thanks
SOURCE: tightening head
New Headbolts are recommended
Long bolts are torqued to 46'lbs + 90 degrees.
Short bolts are torqued 43'lbs + 90 degrees.
Start in the center, and work to the edges, torquing the bolts in two stages.
Rockers are torqued to 22'lbs.
SOURCE: what are the torque specs for the head bolts for a 1999 sportage
hi bob
head torque on the 2.0 DOHC is 64 ft lbs , done in two -three steps , also there is a sequence for proper order . here is a very good description with graphics .
1999 kia sportage 2.0 DOHC head torque
Thanks for using FIX YA !
J5
SOURCE: Head Bolt Torque for a 2000 Grand Cherokee Laredo 4.0L
the torque is a 4 step process
1 torque all bolts to 22 ft/lbs
2 torque all bolts to 45 ft/lbs
3 recheck all bolts to 45 ft/lbs
4 torque bolts 1 thru 10 to 110 ft/lbs
bolt 11 to 100 ft/lbs
bolts 12 thru 14 to 110 ft/lbs
bolt #1 is the fourth bolt from the front on the passenger side....#2 is the fourth bolt on the drivers side then you continue in a clockwise order
SOURCE: Head bolt torque specs needed for 96 tbird 3.8
Head bolts are torque to yeild so you MUST use new bolts.
Tighten cylinder head retaining bolts in numerical sequence in three steps as follows:
Loosen retaining bolts one at a time two to three revolutions and retighten as follows:
Long bolts:
Short Bolts:
Here is a pic of the sequence
http://i253.photobucket.com/albums/hh43/chuck943/Headboltsequence38L.gif
SOURCE: TORQUED HEAD BOLTS TO 60LBS
inch pounds for startersget manual procedure is 6 6 step two step tighten lossen tighten long an short then loose n one at a time an retorque..need proceedure in front of you dealer or part store may copy or print off for you...
Foot pounds (Final torque)
Note:
Torque sequence --------- | 6 2 3 7 | | 5 1 4 8 | --------- Step 1: torque in sequence to 33 Ft/Lbs Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
Foot pounds (Final torque)
Note:
Torque sequence --------- | 8 4 1 5 | | 7 3 2 6 | front --------- of engine | 6 2 3 7 | | 5 1 4 8 | Step 1: torque to 40 Ft/Lbs --------- Step 2: turn an additional 90 degrees Recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
5,393 views
Usually answered in minutes!
×