Question about 1988 Jeep Wrangler

1 Answer

1988 jeep wrangler 6 cyl,i need main bearing torque specs?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 6,982 Answers

80 foot lbs

Posted on Mar 18, 2010


1 Suggested Answer


6ya staff

  • 2 Answers


Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need torque specs 14B coaster bus.cyl head and con rod torque

I need torque specs for toyota coaster bus 14B engine, con rod bearing cap bolts and main bearing

Apr 14, 2017 | Cars & Trucks

1 Answer

Torque specs for rod & main brgs for 1994 ford f150, 300 6 cyl fuel inj engine

Main Bearing Cap Torque:
Torque in 2 steps: Step 1: torque to 35 Ft/Lbs Step 2: torque to 70 Ft/Lbs

The Rod Bearing Cap Torque: 45 Foot pounds (Final torque)

Was this what you needed...let me know by your rating of me...thanks!

Sep 17, 2011 | 1994 Ford F150 Styleside Supercab

1 Answer

I need to replace the exhaust manifold on a 1995 Jeep Wrangler with a 4.0L HO engine. What are the torque specs for the bolts and is there a specific pattern?

Don't have a sendable diagram so here it is in words: Beginning with the bottom row, tighten the center bolt to the right of cylinder #4, then the one just to the left of cyl #3. Then the one directly above at the center of both. Continue by tightening the bolt to the left of cyl#2, then to the right of cyl#5 then the one to the front, left of cyl #1, then the remaining lower bolt to the right of cyl#6. Move to the top row, tightening the ont to the right of cyl #2, then the front, above cyl #1, then the rear ones, above cyl #5, then the far back one above cyl 6. Torque is supposed to be 24 foot lbs except bolts 6 and 7 but I've found it makes no difference. What I've found to be important though is to re check torque after running it up to operating temp and permitting it to completely cool down. Also, never tear it down while it's still hot. That promotes warping.

May 03, 2011 | Jeep Wrangler Cars & Trucks

1 Answer

We have a 1988 jeep wrangler 4.2l 6 cyl that we are looking for the vacuum diagrams for. We have the chilton book but it is not giving us the exact info we need. Please help!

you can find what you need at your local library, they can show you what books to look up, and even print the information for you, normally for about 10 cents a copy.

Apr 12, 2011 | 1988 Jeep Wrangler

1 Answer

What are the torque specs for 2000 cheep cherokee 6 cyl. 4.0

I can give you the specs but for what part of the motor? There is about 120 different head torque,main bearing caps.If you say which area I will happily help you.

Jan 05, 2011 | Jeep Cherokee Cars & Trucks

1 Answer

Need torque specs 1988 Chevy silverado for main bearings and rod

Those values and most everything else you need for DIY work are contained in the Haynes manual for your vehicle. We have one with each of our vehicles and not only give you the info needed to do repairs yourself but also get an idea of how much work a specific repair should (or shouldn't) cost.
'88 Chevy pickup manual
You can also buy these from auto parts stores for a few dollars less and sometimes on eBay for even less.

Feb 20, 2010 | 1988 Chevrolet C1500

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs

I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

1 Answer

1988 jeep will not start put new module and pick up in the distributor no fire 6 cyl jeep wrangler please help

if its equiped with a crank sensor i would chk. that, if crank sensor bad you won't get no spark either.

Feb 02, 2009 | 1988 Jeep Wrangler

1 Answer

1988 jeep wrangle

Check your spark plugs. Without good spark plugs the ignition won't ignite. Just go look for Jeep spark plugs at like AutoZone and they are real cheap. To change them you will need a long socket wrench to twist them out and change each one.

Jan 30, 2009 | 1988 Jeep Wrangler

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

160 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

85219 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides