How can i reset tire monitor - Impala Chevrolet Cars & Trucks

Using the Driver Information Center (DIC)
Important: After resetting, the tire pressure monitoring (TPM) system requires up to 8 km/h (5 miles) of flat, smooth road straight line driving in each of the 4 speed ranges to complete the calibration process. For further information, refer to Tire Pressure Monitor Description and Operation . If the TPM system does not reset, refer to Driver Information Center (DIC) Switch Inoperative .

1. Set all tire pressures to the recommended kPa/psi. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label .
2. Turn ON the ignition, with the engine OFF.
3. Press the vehicle information button until TIRE INFLATION MONITOR SYSTEM PRESS (down/left arrow) SWITCH TO RESET is displayed.
4. If the system is being reset due to a low tire pressure condition, press and hold the down/left arrow button until TIRE INFLATION MONITOR SYSTEM HAS BEEN RESET is displayed. If the system is being reset due to a tire rotation, press and hold the down/left arrow button for 5 seconds.
5. Release the down/left arrow button and TIRE PRESSURE NORMAL is displayed.

It's a sensor that goes off when your tire pressure is too low or too high. Check the air pressure.

The tires must be inflated to what is stated on the driver's door jamb sticker. If your tires are larger than what came factory and require a different pressure than what the door jamb states, the RCDLR must be reprogrammed for such.

Page 2-46 of your owners manual. If you don't have one you can get on online version from the chevrolet website. Just click the owners link at the top of the page.

TIRE MON (Tire Inflation Monitor Reset)
This feature allows you to reset the tire pressure monitor after checking all tire pressures. To clear the LOW TIRE PRESSURE light from the instrument panel cluster and reset the low tire pressure monitor do the following:

1. Scroll, using the SEEK/PSCAN up or down arrows, until TIRE MON appears on the display.
2. Press the PREV or NEXT button to enter the submenu. RESET will be displayed.
3. Press the TUNE/DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second.

The low tire pressure monitor is now reset.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

after you have inflated the tires to the correct pressure press the tire pressure button for a few seconds untill you hear a beep sound .that indicates the tire pressure has been reset. hope that helps

Check the spare tire pressure and make sure it's 32 PSI.

Fix-A-Flat emergency air can will destroy the first generation sensor.

Tire shop will has Tire-pressure monitoring system (TPMS) reset hand held unit to reset the monitoring system.

To reset the tire pressure light you need to get the tool.

You can get the tool here on link below.

http://cgi.ebay.com/ebaymotors/FORD-OEM-TIRE-PRESSURE-MONITOR-RESET-TOOL-TPMS-RESET_W0QQcmdZViewItemQQhashZitem45eed5e149QQitemZ300359737673QQptZMotorsQ5fAutomotiveQ5fTools

TIRE PRESSURE MONITOR RESET PROCEDURE

IMPORTANT: There are 3 different ways to reset the Tire Pressure Monitor (TPM) system. After resetting, the TPM system requires up to 30 minutes of straight line driving in each of the 3 speed ranges to complete the calibration process.If the TPM system does not reset, or DTC C1245 remains current, refer to Diagnostic System Check - Tire Pressure Monitoring. For further information, refer to Tire Pressure Monitor Description and Operation.

USING THE EXTERIOR LAMP SWITCH

1. Adjust all tire pressures to the recommended kPa/psi. Refer to Tire Placard.
2. Turn "ON" the ignition, with the engine OFF.
3. Cycle the exterior lamp switch from "OFF" to parking lamps 3 times within 5 seconds.
4. Use the scan tool in order to clear the TPM DTC.

USING THE RDS RADIO, IF EQUIPPED

1. Adjust all tire pressures to the recommended kPa/psi. Refer to Tire Placard.
2. Turn the ignition to "ACC" or "ON", with the engine OFF.
3. Turn the radio "OFF".
4. Press and hold the "DISP" button until "SETTINGS" is displayed.
5. Press the "SEEK" up or down arrows until "TIRE MON" is displayed.
6. Press the "PREV" or "NEXT" button to enter the submenu. "RESET" will be displayed.
7. Press the "DISP" button, A chime will sound and "DONE" will be displayed.
8. Scroll until "EXIT" is displayed.
9. Press the "DISP" button to exit the TPM reset mode. A chime will sound to verify exit.
10. Use the scan tool in order to clear the TPM DTC

chevrolet usually resets itself after the problem is fixed. unless it is a bad sensor on one of the wheels. also check the spare some spares have a monitor in them.

the last time I had a flat the tire pressure monitor came on a little too late. once the tire was replaced and brought up to pressure it reset itself. check your spare tire. have the tire that was repaired still has the module on the rim. they may have given you a different rim