What is the torque specs for the front wheel bearing/hub assembly nut on a 2002 ford mustang?

The one that fits!

That's not the way it works. you buy a socket set. It has one set of AF Sockets and one set of Metric sockets. The one you use is the one that fits.

Hub and Wheel Bearing Torque Specifications - DRiV

drivcat.com > HubWheelTorqueTableWindow

2009 Ford Fusion ... Front Proc 1 Note ... Front Proc 2 Note ... Do not attempt to tighten the nut with the vehicle on the ground or the wheel bearing will be ...

Front Axle Nut Torque Spec - Lounge - Fusion Energi - Ford ...

www.fordfusionenergiforum.com > topic > 6160-front-...

Dec. 2, 2019 - Im replacing the front wheel bearing assemble this weekend and cant find the torque spec for the ale nut. The older model Fusion (up to 2012) ...

BHA54317 Axle / Spindle Nut Torque Specification - 1A Auto

docs.1aauto.com > BHA54317 Torque Spec

PDF Vehicle Notes. Lb. ft NM. Ford. Fusion. 2006-12 (Excluding All Wheel Drive Models). Rear. Lincoln. MKZ. 2007-12 (Excluding All Wheel Drive Models). Rear.

SKF-Front-Rear-Axle-Nut-Hub-Mount-Lug-Nut-Torque-Spec

dannysengineportal.com > wp-content > uploads > S...
PDF
Front & rear axle nut, hub mount and lug nut torque specifications for FWD ... 3 Series AWD E92, E93 ....2012-2013 . ... FORD / MERCURY TRUCKS - cont.


..

i usually put lock tight blue on them and tore to 65 ft lbs the nut on the axle i usually tore to 50- 60 ft lbs no lock tight

Wheel Bearing and Hub Assembly - Front (MPA WH515006)

Wheel Hub Assembly Axle Nut Torque Spec: 180 ft-lbs / 244Nm, tighten further to align cotter pin with hole. .

the four axle nuts, 98 ft lbs, tighten in criss-cross pattern.
The hub nut/wheel bearing, 148 ft lbs, use new nut, don't let vehicle weight sit on the ground while torqueing, it could damage the wheel bearing.
If I left something out, give me a holler.

Three bolts are 70 lbs,could be 120+/-.

Here are the specs you're looking for:
• Font axle to hub nut torque 185 ft-lbs
• Front hub bearing bolts 60 ft-lbs
• Caliper housing bolts 125 ft-lbs
• Caliper guide bolts 26 ft-lbs
• front spindle hub nut 97 ft-lbs
• lug nuts 100 ft-lbs.

The front wheel bearing is a hub and bearing assembly. To remove you will.... 1. Remove the tire 2. Remove the axle nut. You can put a punch in the fins of the rotor to keep the assembly from turning while you rmove the nut. You can can do the same thing when you torque the axle nut. 3. Remove the caliper and rotor. 4. Unplug the abs sensor if equipped. 5. Remove the three bolts that hold the hub to the knuckle. 6. Rmove the hub. If you need torque specs let me know and i'll get them for you. It is absolutely critical that you torque the axle nut to the proper spec!

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Remove tire/wheel. (5 nuts)
Seperate the brake pads just a little; pry apart with a screw driver. Easier to remove and replace later.
Remove caliper/brake assembly (2 bolts). Do NOT remove brake line.
Remove brake rotor (there may be a retainer clip or two that needs to be removed and discarded.
Remove black center cap (after reading warning on the cap).
Remove large spindle nut.
Slide bearing/hub assembly off the spindle. (If stuck, you may have to tap it with a hammer. It's a straight smooth shaft.

Reassemble in reverse order.
Tighten the nut to the correct torque spec. I don't know what it is, but it's pretty high... 200ft-lbs? The torque is important because it sets the preload on the bearing balls and races. Too low or torque will cause early bearing failure.

Bearing/hub looks like this:

do not replace only the bearing. replace hub assembly. remove rim/tire , remove caliper, mounting plate, rotor. . un bolt hub assembly, unplug abs. remove front axle nut if 4x4. you may need to rent the axle nut remove kit and hub puller. pull out hub. drive axle reward out of hub. install new part. do not torque hub over 90lbs. check with parts sell for spec

112 to 174 ft lbs