Yes you are right grace also uses a be as a cover bank 2 is always the drivers side as your facing the engine or closest to the radiator on front wheel drive engines that knock sensor is located on the back of the engine under the intake manifold it's above the exhaust pipe and near the axle you can see it at rockauto.Com in emissions and there's a video on YouTube from 1A auto how to replace engine Toyota camry knock sensor 92-01 you will need a 27 mm wrench to do it so go to sears or another quality tool store to buy a set don't waste your money on the cheap stuff they can strip the head of the sensor and then your in deep mud ok you get what you pay for and if your doing your own stuff regularly it will pay off in the end ,but the cheap stuff Cando it if you need to keep the $$ down good luck this is pretty easy and watch out for the spammersthey know nothing
Yes you are right grace also uses a be as a cover bank 2 is always the drivers side as your facing the engine or closest to the radiator on front wheel drive engines that knock sensor is located on the back of the engine under the intake manifold it's above the exhaust pipe and near the axle you can see it at rockauto.Com in emissions and there's a video on YouTube from 1A auto how to replace engine Toyota camry knock sensor 92-01 you will need a 27 mm wrench to do it so go to sears or another quality tool store to buy a set don't waste your money on the cheap stuff they can strip the head of the sensor and then your in deep mud ok you get what you pay for and if your doing your own stuff regularly it will pay off in the end ,but the cheap stuff Cando it if you need to keep the $$ down good luck this is pretty easy and watch out for the spammersthey know nothing
×
Ya just get a help manual for repair. simple! I have repaired a lot of cars mine and my frnds cars and bikes using free manuals only.. u will find it on www.reliable-store.com
Just try to get one asap
You will get the service manual along with diagram from the given link https://toolsnyou.com/
SOURCE: knock sensor location
It's under the intake manifold. To access it you have to remove the manifold and injection rail.
SOURCE: Need to locate knock sensor on 1999 camry V6. Where is located.
i have toyota windom 4vz-fe i need locate knock sensor
SOURCE: Where is the knock sensor 2 (bank 2) located on a
I don't have a diagram but they are under your intake manifold. It's not to bad of a job. You don't have to remove the fuel rails or the injectors, they can come up with the intake. The #2 knock sensor is the one in the rear. I will suggest getting both of them and also the harness and do it all while you have it apart. I believe you will find that water has gotten down in the hole where the knock sensors are located. Make sure to clean it out very good with compressed air before you install your new knock sensors.
SOURCE: Where is the knock sensor located? 2000 Toyota
remove the intake manifold ,remove radiator ,remove radiator intake and outake housing, remove fan ,remove all belts: power steering, alternator and if you have a/c, remove harmonic balancer ,remove timing belt covers, remove timing belt remove intake housinng once you have remove all the above, your freaken engine will look naked, you can see the location of the knock sensor is locate in the engine valley
SOURCE: How do I replace a knock sensor for a 1992 toyota
First, I would like to mention that most knock sensor codes are not caused by the knock sensors, but a mechanical problem with the engine. The knock sensors cannot differentiate between noises caused by mechanical problems like a bad pulley bearing, bad motor mount, noisy alternator bearings, etc. and spark knock. knock sensor codes are set when the computer has retarded the timing as far as possible to compensate for ignition ping (Spark Knock) and the noise still exists.
With that said, here are the instructions.
Remove the Intake Chamber assembly.
Disconnect Injector connectors.
Disconnect the heater hose from the Intake Manifold.
Remove the 9 bolts. 2 nuts, 2 plate washers and Intake Manifold assembly.
Remove right hand engine mounting stay and water outlet.
Disconnect the following hoses and connectors:
Radiator inlet hose.
Engine coolant reservoir hose.
Engine Coolant Temperature Sensor connector.
Engine Coolant Temperature Switch connector.
Ground strap connector.
Remove the 3 bolts and right hand mounting stay.
Remove the wire band.
Disconnect the water bypass hose from the inlet housing.
Remove the 2 bolts, 2 nuts, 2 plate washers and water outlet.
Remove the 2 gaskets.
Disconnect the Knock Sensor connectors.
Remove the Knock Sensors.
57 views
Usually answered in minutes!
Earning in the modern life is not as difficult as it is thought to be. God has made man for comfort then why we are so stressed. We are giving you the solution of your problems.go to home media tech tab for more detail....... HERE? easywayearn.xyz
×