, in inch pounds what is the torque specification for the bolts on a valve cover on the ML430

In the link and a video as well. NOTE: they are POUND INCH not Foot Pounds.

Torque Pattern for Valve Cover? - Kia Forum

kia-forums.com https://www.kia-forums.com > threads > torque-patter...
Sep 17, 2013 - show the locations of the bolts on the "Cylinder Head Cover" --aka valve cover-- and they provide the torque at 35-52 lb-in (4-6Nm), but they ...

Valve Cover Gasket help
Apr 28, 2012
Torque specs and sequence for intake bolts
Jul 10, 2022
Need Bolt Pattern for Valve Cover, please help?
May 15, 2018
torque specs?
Mar 20, 2017
More results from www.kia-forums.com

..

Question edited for clarity and apparently it is a GXL not GLX.
Question moved to model category.

106 INCH Pounds, or 9 foot pounds.

2000 Toyota Land Cruiser 4.7L Engine Torque Specs

https://toyota-specs.com > cars > cruiser4.7 > torque-spe...
Valve Covers Installation The valve cover bolts torque down to 106 in-lbs or about 9 ft-lbs in a criss cross order. Be sure not to miss any bolts to avoid ...

With the rubber gasket , you shouldn't need to add any gasket sealant to hold it on. Make sure that the track for it on the valve cover and the surface it sits on, on top of the head are clean.

It is best to replace the grommets on that valve cover by putting them on the bolt first then into the valve cover. This model tends to have issue breaking/tearing the grommets. There should also be grommets for other things like the filler tube and breather tube.

As far as I have ever encountered, I know there is an order to put the bolts back in. I've never use a specific order myself. Most importantly in this model the bolts should be re-installed to 106 INCH pounds. Make sure the torque wrench is on INCH pounds not foot pounds.

24 to 30 inch pounds nut most people don't use a torque wrench. IF you don't have one that read inch pounds tighten them to where the gasket just bulges slightly and stop.

valve cover gasket torque spec? - Bimmerforums

www.bimmerforums.com/.../showthread.php?...valve-cover...torque-spe...

Dec 7, 2012 - Remember the little rubber grommets around the cover bolts? ... Location: alabama; Posts: 5,537; My Cars: 2002 bmw 325 ... Torque spec for the M52 valve cover bolts is 89 inch-pounds / 7.4 ... 1976 - 1989 (E24) · 2004+ (E63, E64) ... 2012+ X1 (E84) · 2003+ X3 (E83,F25) · 1999+ X5, X6 (E53, E70, E71). Valve Cover Bolt Torque Specs
Oct 25, 2014
Valve cover screw torque specs?
Nov 9, 2012
leaking valve cover gasket
Dec 29, 2011
How specific for torque specs?
Dec 27, 2011
More results from www.bimmerforums.com

There is a torque spec for the cylinder head; I don't know of one for the cover.

I don't have the figure you need on file but i seem to remember the bolts are 6 mm, though it has been a while since I saw one of those cars.
Valve or cam cover bolts aren't usually torqued because they aren't critical and it is a matter of letting experience and good sense prevail.

If a torque figure is really wanted then it will be a matter of just a few pounds-inches. There are charts a-plenty freely available that will provide you with the maximum torque suggested for any size of bolt but again good sense must prevail and the actual figure used in practice, especially if the bolt is oily will be probably only half of the maximum.
For a 6 mm bolt this will be in the region of 25 inch-pounds.

the torque spec's are 71-89 inch pounds. start with the center bolts then work out in an opposite, (criss/cross) pattern, like you would tightening wheel lugs. please rate if this helped!

IF YOU TALKING ABOUT TIMING CHAIN COVER TORQUE ON SMALL BOLTS 57 - 66 INCH POUNDS. LARGE BOLTS TORQUE IS 144 - 168 INCH POUNDS. NOW IF YOU ARE TALKING ABOUT TIMING CHAIN LOWER GUIDE BOLTS. TORQUE IS 108 - 168 INCH POUNDS.

The torque spec on the valve cover bolts is 3 ft pounds or 36 inch pounds.
This spec is good for all Chevy small blocks.