Need the torque settings for a Ford Focus Ecoboost 1.0 Main Bearing Caps please

The torque should be around 12 to 18 ft/lb (16 to 24 Nm) on most engines. The settings for the Focus and the Escape are slightly different so work to about 15 ft/lb (20Nm) for both cars.

Knock Sensor Bolts 177 lb in
NOTE: INCH pounds.

All-In-One Torque Spec List

Ford Focus RS Forum https://www.focusrs.org > ... > Focus RS Maintenance
Jan 3, 2020 - All-In-One Torque Spec List ; Knock Sensor Bolts, 177 lb in ; oil filter adapter bolts, 18 ; coolant outlet adapter bolts, 89 lb in ; cylinder head ...

Ford Windsor Torque Specs - Help Center - Summit Racing

https://help.summitracing.com > answers > detail > a_id
Apr 11, 2018 - Main Cap Bolts, 60-70 ft.-lbs. ; Connecting Rod Bolts, 22-25 ft.-lbs. (40-45 ft.-lbs. for 289TP and Boss 302) ; Cylinder Head Bolts, 65-72 ft.-lbs ...

Bolt Torque Spec Chart for Ford Engines - Maine Mustang

http://mainemustang.com > 65-73 Mustang Data
Ford Engine Bolt Torque Chart ; Main cap bolts, 60-70 ft-lbs ; Outer 2 bolts of main cap bolts, 35-40 ft-lbs.(for 4 bolt main bearing caps only ) ; Connecting rod ...

5.0 HO Engine Bolt Torque Specs - Foxstang.com

https://www.foxstang.com > 5-0-ho-torque-specs
Feb 21, 2020 - 5.0 HO (302) Head Torque Specs · Step 1: 23-35 FT/LBS · Step 2: 45-55 FT/LBS · Step 3: Additional 90 degrees (or 75-85 FT/LBS) · Use tightening ...

Ideally you need a Workshop Manual. Help here

https://www.google.com/search?q=Ford+Bantam+1.6+Rocam.+Crankshaft+torque+settings

Service manual

https://www.google.com/search?q=Ford+Bantam+1.6+Rocam+service+manual

..

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

Hi Derek any luck on this as I am also considering rebuild my engine as the big ends went found a crankshaft and bearing but no torque specs ???
checked on automata and it says don't not dismantle the lower part of engine ?
when I spoke to fords they only sell a short block funny that

Okay, the main bearing caps only have 10 bolts, i think your looking for the connecting rod caps, they have 16 bolts, i will list them both, theres a tightening sequnce for the main bearing caps, these are the caps that hold the crankshaft to the engine block, the connecting rod caps hold the pistons to the crank and they have 16 nuts,For a 2004 mazda 6 with the 3.0 engine the torque specs are as follows.
Connecting rod bolts step 1) 19.2 - 23.6 ft lbs.
step 2) tighten an additional 80 - 100 degrees

Main bearing caps step 1) 32.5 - 33.9 ft. lbs.
step 2) tighten an additional 175 -185 degrees.
heres a diagram for main caps to tighten in order.
hope this is helpful.

Head bolts, 105-112 Foot pounds (Final torque)
Final torque must be reached in 3 equal steps. Recheck final torque in sequence.
Main Bearing Caps, Torque in sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs
Rod Bearing Caps, 45 Foot pounds (Final torque)

2002 2.0L Duratech.

Don't have 2004 2.3L

• NOTE: Use new connecting rod bearing cap bolts.
  NOTE: Do not fully tighten the connecting rod bearing cap bolts at this stage.
  Install the bearing caps.

• Rotate the crankshaft through 180 degrees and insert pistons 2 and 3.

• Position the corresponding bearing shells, clean and free of oil, into the connecting rod and the connecting rod bearing cap.

• Coat the inner side of the bearing shells with engine oil.

1. NOTE: The crankshaft must rotate freely, if necessary check and adjust the bearing clearances.
   Tighten the main bearing and connecting rod bearing bolts.
   1. Tighten the main bearing bolts in two stages.
      • Stage 1: 25 Nm.
      • Stage 2: 60 degrees.
   1. Tighten the connecting rod bearing bolts in two stages.
      • Stage 1: 35 Nm.
      • Stage 2: 90 degrees.

Torque sequence:
Step 1: Torque 29 to 34 Ft/Lbs
Step 2: Torque an additional 90 to 120 degrees