What is the torque spec for the water pump on a 2003 Toyota Sienna, 3.0 engine

Question edited for maker.
Question moved to category.

2001 Chevy Monte Carlo 3.8L Engine Torque Specs

https://chevy-specs.com > cars > monte3.8 > torque-spe...
2001 Chevy Monte Carlo 3.8L Complete Torque Specs List ; Water Pump Bolts Torque Spec (Long), 15 ft-lbs + 40° ; Water Pump Pulley Torque Specs, 10 ft-lbs.

..

i know few
error codes/ fault codes, wiring diagrams, schematic diagrams, torque specs, engine info, switches functioning, assemble, disassembly, complete refurbish, repair, installation every single thing is covered
within seconds u can get the access and it's totally illustrative complete

20. INSTALL CYLINDER HEAD COVER SUB-ASSY
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:

Remove any oil from the contact surface.

Install the cylinder head cover within 3 minutes after
applying seal packing.

Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Install the engine wire harness with the 3 nuts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)
21. INSTALL CYLINDER HEAD COVER SUB-ASSY LH
(a) Apply seal packing to the cylinder head as shown in the
illustration.
Seal packing: Part No. 08826-00080 or equivalent
NOTICE:

Remove any oil from the contact surface.

Install the cylinder head cover within 3 minutes after
applying seal packing.

Do not start the engine within 2 hours after installing.
(b) Install the cylinder head cover with the 9 bolts. Tighten the
bolt uniformly in several steps.
Torque: 8.0 Nm (80 kgf cm, 71 in.lbf)
(c) Using an E6 torx) socket wrench, install the engine wire
harness protector with the 2 bolts.
Torque: 8.4 Nm (85 kgf cm, 74 in.lbf)

This is year/make/model specific to the 2nd Gen Sienna. Taken from the 05 Toyota Sienna repair manual. Hope this answers your torque specs for the valve covers which uses 10 mm bolts. If in doubt, as Scotty Kilmer asserts, do a "German tight".

the water pump bolts torque specs is T=1.85 kg-m (13 ft-lb). you must set your torque wrench nicely and carefully not to break the bolts then there you go.

Depends on the gasket used, but 7 to 14 foot pounds. I just snug them up with a ratchet one hand.

go on line -typr in torque specifications for toyota 1jz engine and there will be a pdf spec sheet of all the vehicle torque settings.

normal torque specs for wheel nut is 110 NM

Spark plug torque on the 3.0L engine is 13 ft.lbs. and the 3.3L is 18 ft.lbs.

Valve covers-69 inch lbs.

Intake Manifold-11 ft. lbs.

Welcome to FIxYa.com

THERMOSTAT REMOVAL

HINT: Removal of the thermostat would have an adverse

effect causing a lowering of cooling efficiency. Do not remove

the thermostat, even if the engine tends to overheat.

1. DRAIN ENGINE COOLANT

2. REMOVE AIR CLEANER CAP WITH AIR CLEANER

HOSE

3. DISCONNECT ECT SW1TCH CONNECTORS

4. DISCONNECT ENGINE VIRE PROTECTOR FROM

WATER INLET AND RH CYLINDER HEAD

Remove the 2 nuts, and disconnect the engine wire

protector from the water inlet and cylinder head.

5. DISCONNECT WATER INLET PIPE FROM WATER

INLET AND LH CYLINDER HEAD

a) Remove the bolt and disconnect the inlet pipe from the

water inlet.

b) Remove the O-ring from the inlet pip e.

6. REMOVE WATER INLET AND THERMOSTAT

a) Remove the 3 nuts, water inlet and thermostat.

b) Remove the gasket from the thermostat.

INSPECTION

INSPECT THERMOSTAT

HINT: The thermostat is numbered with the valve opening

temperature.

a) immerse the thermostat in water and gradually heat the

water.

b) Check the valve opening temperature.

Valve opening temperature: 80 - 84CC (176- 183 deg f)

If the valve opening temperature is not as specified,

replace the thermostat.

c) Check the valve lift.

Valve lift: 10.0 mm (0.394 inch) or more at 95CC (203 deg f)

If the valve lift is not as specified, replace the

thermostat.

d) Check that the valve is fully closed when the

thermostat is at low temperatures (below 40CC (104CF)).

if not dosed, replace the thermostat.

INSTALLATION

1. PLACE THERMOSTAT IN WATER PUMP

a) Install a new gasket on to the thermostat.

b) Align the thermostat jiggle valve with the upper stud

bolt and insert the thermostat in the water inlet

housing.

HINT: The jiggle valve maybe set within 15 deg of either

side of the prescribed position.

2. INSTALL WATER INLET

Install the water inlet with the 3 nuts.

Torque: 8.0 Nm (80 kgf-cm, 69 inch lbs.)

3. INSTALL WATER INLET PIPE

a) Install a new O-ring to the water inlet pipe.

Thank you for using FixYa.com

Regards, Lee Davidian

heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbs