Question about 2005 Chevrolet Aveo
Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Good luck!
Posted on Jan 02, 2017
SOURCE: Windshield wipers stay on delay all the time.
A wire is shorted out or part of the switch is bad.
Posted on Aug 28, 2008
SOURCE: wipers only work on high, does not work on delay
The wiper motor control module needs to be replaced, if you can buy one. The control module is mounted to the wiper motor. If you can't buy just the module, you will need to buy the entire unit. I am pretty sure you need the control module, but you can verify this by unplugging the plug that goes into the wiper motor and checking each of the pins on the plug with a 12 volt test light connected to ground while someone operates the switch. If the switch is good, you will get voltage on high as well as delay. I was able to locate an entire assembly on EBAY for less than the cost of the module from the dealer. Good luck!
Posted on Jan 03, 2010
SOURCE: delay wipers only work on
Hello, my name is Ben and I can help you with this problem. This is a very common problem with Chevy. You need what is known in most vehicles as a "pulse board". The pulse board is located inside the wiper motor control module. On many vehicles the pulse board is replaceable, unfortunately on your Silverado you must replace the entire Wiper Motor Control Module which is bolted onto the top of the wiper motor. To get to the wiper motor, first remove those little nut covers on the big end of the windshield wiper arms, if you slip a small screwdriver or your fingernail they just pop off. Now unbolt the windsheild wiper arms, before removing the wiper arms, mark their location on the windsheild with a grease pencil or magic marker. The arms are hard to remove, you need to kinda wiggle and pull at the same time, now that long plastic cowl needs to come off, those clips at the front edge just slide forward, then at each end lift up that rubber flap and remove those TORX screws. Remove the cowl and set it somewhere SAFE, it's easy to break. You will now see the control module mounted on the wiper motor, unplug the electrical connections and remove the TORX screws holding it to the motor. Assembly is the reverse of dis-assembly. If you have any trouble or questions, feel free to ask, Ben.
Posted on Nov 13, 2010
Testimonial: "Thank You I never would have found it 114.00 at auto store"
SOURCE: wipers quit working low speed & delay, wont park. work fine high speed. have changed sw, didnt help
When they won't park it's 99% need new wiper motor
Posted on Nov 06, 2011
SOURCE: 2000 Chevy Malibu wiper delay and intermittent won't work.
I had this problem (wipers only work on high) with my 2002 Chevy Malibu and had to replace the 6 amp diode (22059733) on the wiper control board. It is connected to the back of the wiper motor and is held on by 3 torx screws.
Radio Shack has them for $2.75 6A, 50V Rectifier Diodes (4-Pack) Model:276-1661
Posted on Aug 15, 2012
Sep 27, 2016 | 2012 Chevrolet Chevrolet Captiva Sport LTZ
Nov 14, 2015 | 2005 Chevrolet Aveo
Oct 29, 2012 | Cars & Trucks
Jun 12, 2012 | 2005 Chevrolet Equinox
Jun 25, 2010 | 2004 Chevrolet Aveo
Nov 17, 2009 | 2005 Chevrolet Aveo
Jul 11, 2009 | 2001 Chevrolet Venture
Mar 18, 2009 | 2006 Chevrolet Aveo
Jan 13, 2009 | 2005 Chevrolet Aveo
44 people viewed this question
Usually answered in minutes!
×