Question about 1997 Jeep Wrangler

3 Answers

Low transmission fluid level

Where do i add transmission fluid

Posted by on

Ad

3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 497 Answers

You add it right to the transfer case. on the transmission

Posted on Aug 27, 2009

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 4,044 Answers

If this is an Automatic you have to use a funnel to pour the fluid into the Dipstick pipe. If this is a manual transmission there is a plug on the side of the transmission under the vehicle that you need to pull and add the fluid in. i would recommend you get a Manual on your vehicle at autozone if you believe you Manual Transmission is low on fluid so you will have detailed instructions on how to check and fill the transmission.

Posted on Aug 27, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 273 Answers

There is a rubber plug on top of the gearbox should be fairly accessible

Posted on Aug 27, 2009

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

carlsbiz

Carl

  • 1124 Answers

SOURCE: !995 jeep gr cherk. transmission fluid. add hot

Its best to add while all is hot..
Leave it runing in park while adding fluid..
Put a little at a time and keep checking being careful not to over fill..
The dipstick mesures in pints - not quarts..

Rate well ;o)

Posted on Jul 22, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission fluid


You need to remove transmission dipstick, use the narow long funnel and pour the transmission fluid that way. Please check the level of transmission fluid only when vehicle was driven for at least half an hour. Park the vehicle on level surface and whit engine off check the transmission dipstick for range of fluid . If fluid is low add carefully to the center mark of the dipstick between minimum and maximum range. Drive vehicle or select each gear down and back holding your brake and at each gear for 10 seconds up and down the shifter. Check the level again and add if needed. Repeat til you have reach that level. Do not overfill it!

Nov 07, 2013 | 1996 Ford Windstar

1 Answer

Transmission fluid hose burst, fixed it, add fluid now the car won't move...


Two litres? Unless you are outside the USA, transmission fluid generally comes in quart containers. If you only added 2 quarts, yes, it's very possible the fluid level is low. However, you don't want to add too much. There should be a dip stick for checking fluid level. Run the vehicle until the engine is good a warm, about 15-20 minutes, and then check the fluid level. Add as needed. But remember, don't add too much. Add a little at a time, as you get close to full.

Feb 05, 2013 | 1999 Oldsmobile Alero

1 Answer

How much trannyfluid goes in a 99 gmc sonoma


5 QUARTS FOR FLUID FILTER CHANGE. IF REPLACING TORQUE CONVERTER OR TRANSMISSION OVER HAUL. YOU NEED 13.8 QUARTS. WHEN YOU CHANGE FLUID AND FILTER.BESURE YOU HAVE TRANSMISSION FLUID LEVEL TO THE FULL MARK BEFORE DRIVING VECHICLE.LET ENGINE IDLE UNTIL GET WARM BUT CHECK TRANSMISSION FLUID WHILE ENGINE IDLING.IF FLUID LEVEL DROP A LITTLE ADD A LITTLE MORE TO GET FLUID LEVEL AT FULL MARK.ONCE ENGINE GET OPERATING TEMPERATURE.SHIFT TRANSMISSION THROUGH ALL GEARS TWICE ONE AT A TIME.CHECK TRANSMISSION FLUID LEVEL.SHOULD BE ON FULL MARK.DRIVE VECHICLE FEW MILES CHECK FLUID LEVEL.IF FLUID LEVEL.FULL YOU GOOD.IF STILL LOW ADD A PINT AT A TIME.ONCE FLUID LEVEL CORRECT. SHIFTING OKAY TIME PLAY.YOU GOOD TO GO.

Jan 22, 2011 | 1999 GMC Sonoma

1 Answer

1995 lincoln occasionally has problems getting in gear to go. Seems like it is stuck in neutral. Lasts a few seconds then it gets into gear and goes.


SEEMS LIKE TRANSMISSION FLUID LOW.TRANSMISSION SLIPPING TRYING TO GO IN DRIVE.CHECK TRANSMISSION FLUID LEVEL. IF LOW ADD FLUID UNTIL YOU REACH FULL MARK ON TRANSMISSION DIP STICK. WITH ENGINE RUNNING A IN OPERATING TEMPERATURE.IF FLUID LEVEL OKAY.CHANGE TRANSMISSION FLUID AND FILTER IF YOU HAVE NOT CHANGED IN A LONG WHILE.A DIRTY STOPPED UP FILTER WILL CAUSE TRANSMISSION TO SLIP.CANT PICK UP FLUID.

Dec 26, 2010 | 1995 Lincoln Town Car

1 Answer

My tranny slips some times but it will catch after a few min


SOUND LIKE TRANSMISSION FLUID LOW OR YOU NEED A TRANSMISSION FLUID AND FILTER CHANGE.THE 4T40E OR 4T45E IF YOU DONT SEE TRANSMISSION DIP STICK.BEST TO DO A FILTER AND FLUID CHANGE.YOU NEED 7 QUARTS OF TRANSMISSION FLUID A NEW TRANSMISSION FILTER AND PAN GASKET.I WOULD BUY FILTER AND PAN GASKET AT DEALERSHIP.YOU NEED A LARGE DRAIN PAN TO CATCH TRANSMISSION FLUID.IF YOU HAVE A TRANSMISSION DIP STICK. BEFORE YOU FIRST BEFORE STARTING THE ENGINE CHECK TRANSMISSION FLUID LEVEL ON DIP STICK.SHOULD BE ON THE FULL MARK.IF NOT ADD FLUID TO FULL MARK.THEN CRANK VECHICLE LET IDLE UNTIL ENGINE HOT OPERATION TEMPERATURE ABOUT 10 MINUTES.THEN APPLY BRAKE PEDAL.THEN SLOWLY SHIFT TRANSMISSION SHIFTER THROUGH ALL GEARS 2 TIMES.THEN PUT TRANSMISSION IN PARK.CHECK TRANSMISSION FLUID LEVEL.IF NOT AT FULL MARK ADD TRANSMISSION FLUID UNTIL LEVEL CORRECT.

Nov 13, 2010 | 1999 Oldsmobile Alero

2 Answers

Need to add transmission fluid in Cadillac CTS 2004. How do you do it?


tod34 is correct. The "fill" area of this transmission is located on the transmission itself. It is a fluid leveling plug located low on the main case toward the back of the trans. You must pump the fluid in through that hole. If you are on level ground and the transmission is properly warmed, you should fill the transmission until the fluid level is flush with the bottom of the hole (starts spilling out)

Dec 28, 2009 | 2006 Cadillac CTS

1 Answer

Drive or reverse takes a moment before it engages sometimes i have to increas rpms


This is a simptom of low transmission fluid - check your transmission fluid level by pulling the dip stick out of the transmission (found in engine compartment) - must have the enigne running - e brake on and in neutral - if level is low add mopar transmission fluid - if level is good there is an internal problem in the transmission

Dec 02, 2009 | 2000 Dodge Stratus

2 Answers

How do i add transmission fluid to my 1996 camry?


If you have a dipstick under your hood for the tranny fluid, then fill it in there slowly... if not, you'll need to fill it through the filler plug that will be on the side of the transmission just above the halfway point

Sep 08, 2009 | 1996 Toyota Camry

1 Answer

Where do I check the transmission fluid on a 1997 Hyundai excel


Remove Transmission Fluid Level Check
Locate and remove the transmission fluid level checker, in most cars and trucks this is where the fluid is checked and added.
1687565.jpg
Insert fluid funnel and add transmission fluid until the proper amount of fluid level is reached. Let engine warm and recheck fluid level, add fluid as needed. Do not over fill the transmission, it could foam the fluid and cause low fluid pressure causing premature transmission failure. recheck transmission for leaks and recheck fluid level in a couple of days.

DIAGNOSIS AND TEST FLUID LEVEL AND CONDITION
1. Park the vehicle on a level surface. 2. Before removing the dipstick, wipe all dirt from the area around the dipstick. 3. With the selector lever in "P" (Park) and the parking brake applied, start the engine. 4. The engine should be running at idle speed and the fluid should be at normal operating temperature [80-90°C (176-194°F)]. 5. Move the selector lever to every position to fill the torque converter and hydraulic circuit with fluid, then place the lever in the "N" (Neutral) position. This operation checks that fluid level check is accurate. 6. Check if the fluid level is in the "HOT" range shown on the dipstick. If the fluid is low, add automatic transaxle fluid until the level reaches the "HOT" range.
ab7f169.gif

Aug 13, 2008 | Hyundai Excel Cars & Trucks

Not finding what you are looking for?
1997 Jeep Wrangler Logo

374 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...