Question about Saturn Ion

Open Question

Where is Evap canister vent solenoid valve located on 2004 staurn Ion 2.2

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 275 Answers

SOURCE: 2004 Pontiac Grand Prix Evaporative Canister

you should be able to fix it look for a can near the fuel tank that has vacuum hoses coming out of it and you should be able to just buy the bad solenoid

Posted on Nov 03, 2008

Ad

Rick Gillis

  • 37 Answers

SOURCE: HAVE A TROUBLESHOOTING MESSAGE PO446

DTC P0446 Evaporative Emission (EVAP) Vent System Performance

The vehicle control module (VCM) monitors the performance of the evaporative emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this diagnostic trouble code (DTC) if the vacuum decay rate is more than a predetermined value. The VCM monitors the amount of vacuum and the amount of pressure in the EVAP system by monitoring the fuel tank pressure sensor. For this DTC, the VCM turns ON both the EVAP purge valve and the EVAP vent valve when the Conditions for Running the DTC are met. This applies an engine vacuum to a closed EVAP system. The VCM turns OFF both the EVAP purge valve and the EVAP vent valve when the system reaches a correct amount of vacuum. The EVAP system should quickly RELEASE the vacuum in the EVAP system with the EVAP purge valve OFF and the EVAP vent valve OFF (open). This test indicates a blocked or restricted EVAP vent path if the EVAP system fails to release the vacuum quickly enough.

3208f98.gif


Posted on Dec 06, 2008

Michael Gutwein

  • 104 Answers

SOURCE: I have a 2004 Avalanche, 49K mileage, code PO446,

That is an EVAP code. its a vent control code. you can manually test it by powering it up if you know where its at. i cant remember exaclty where its at off the top of my head but its only 2 wires. using a volt meter you want to make sure power is getting to it, but you cannot activate it without dealer scan tool.hmmm if you can figure out which is ground and power when you give it 12 volts it should click. meaning your vent solenoid works and you have wiring problems or its leaking.

EVAP problems are hard to finde with out scanners. you can change the vent solenoid and hope it fixes it. but a code points you to the direction of a problem. hopefull its not wiring problems. in the northern states with snow. ice can pull out wires and also get clogged in the vent solenoid and lock it up. its either wiring or bad or a leaking solenoid. check condition of wires. if they look good try a vent soleniod.

if that doesnt fix it after a engine light reset and 2 weeks or so. then goto dealer. you need to reset it after repair. light will not go off on its own.GOOD LUCK

Michael
ASE certified.
plz rate

Posted on Apr 29, 2009

MNfisherman

Nate Stansfield

  • 11896 Answers

SOURCE: replacing the evap canister

It is the big black box on driver side front next to fender. It has to vacuum hoses going to it.

Posted on Jul 10, 2009

David

  • 37 Answers

SOURCE: 2004 Chevy Cavalier 2.2 eco Automatic 94,000 miles

in my experience the usual culprit is the evap cannister. the problem is it gets moisture in it and freezes during winter thus cracking the plastic. if you lay under the car and look at the evap box it black plastic and if you see a loose or cracked hose or the box itself is cracked that is most likely it. as a side note you can check the gas cap and buy a new one to see if that rectifies the situation. lastly i don't think the gas tank should be suspect as you would probably notice if gas was leaking out of the tank. if you take the car to a dealer or shop they can do a smoke test and determine where the leak is.

Posted on Oct 19, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the Vapor Canister Vent Solenoid located on a 2003 Chevy Silverado 1500, 4.3L engine? And do you ave to remove the pick-up bed to access it, if it is on top of the tank?


No you don't have to remove the pick up bed to get at it. It's on the left frame rail along side of fuel tank !
Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister vent electrical connector, if equipped. Disengage the 2 vent valve pipe clips securing the pipe to the underbody.
Remove the clips from the underbody and discard.
Disconnect the vent valve pipe at the EVAP canister. Remove and retain the EVAP canister vent valve bracket mounting bolt. Remove the complete EVAP canister vent valve assembly with bracket attached and discard.
Notice: Refer to Fastener Notice in the Preface section.
Video on youtube !

Dec 31, 2015 | Cars & Trucks

1 Answer

Where is purge valve located?


How to test and replace the EVAP Canister Purge Volume ...

? 13:49
https://www.youtube.com/watch?v=QnVUBYdFHGI
Mar 29, 2014 - Uploaded by CarsNToys
The EVAP canister purge control volume control valve is operated by a step motor for control of flow rate of fuel vapor fromEVAP canister.

How To Install Replace Vapor Canister Solenoid Purge ...

? 2:14
https://www.youtube.com/watch?v=TZ6ZB_acC9w
Sep 16, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/vapor-canister-purge-solenoid-valve-ac-delco- ... How To Test and Replace EVAP Canister Vent ControlValve P0446 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by ...


Dec 18, 2015 | Cars & Trucks

1 Answer

Where is purge valve solenoid located?


Mar 16, 2014 - 2 posts - ‎1 author
I have a 2003 Vue 3.0L 2wd.After fueling I have trouble starting, it cranks but I have to pump it a couple of time then it starts, Sometimes after it ... 2008 Saturn Vue Purge valve canister solenoid location ...
9 posts
Aug 24, 2013
access to vent valve solenoid - SaturnFans.com Forums
2 posts
Jan 20, 2013
Service engine soon light: P0440 - SaturnFans.com Forums
6 posts
Apr 15, 2010
Code P0446 (evap solenoid) and now I can't fill the gas ...
16 posts
Nov 17, 2007
More results from www.saturnfans.com

EVAP Solenoid Location - YouTube

? 2:17
https://www.youtube.com/watch?v=jIKaPF2Yw3I
Mar 20, 2007 - Uploaded by richpin06a
Saturn EVAP Solenoid Location. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by CarsNToys ...

EVAP Purge Solenoid Removal - YouTube




Dec 11, 2015 | 2003 Saturn VUE

1 Answer

2007. What are the probable causes of DTC P0446?


DTC P0446: Evaporative Emissions (EVAP) Vent System Performance
Circuit/System Description
This DTC tests the evaporative emission (EVAP) system for a restricted or blocked EVAP vent path. The control module commands the EVAP canister purge solenoid valve Open and the EVAP canister vent solenoid valve Closed. This allows vacuum to be applied to the EVAP system. Once a calibrated vacuum level has been reached, the control module commands the EVAP canister purge solenoid valve Closed and the EVAP canister vent solenoid valve Open. The control module monitors the fuel tank pressure (FTP) sensor for a decrease in vacuum. If the vacuum does not decrease to near 0 inch H2O in a calibrated time, this DTC sets.
Diagnostic Aids
?€¢
An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent solenoid valve inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill problem.


?€¢
An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.


?€¢
An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission Canister Replacement .


?€¢
Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system


Do you have a scan tool that reads data PID'S ?
Your FTP - fuel tank pressure sensor could be at fault !

    Ignition ON and fuel cap removed, verify that the FTP sensor parameter is between 1.3-1.7 volts. ?‡'
    If not within the specified range, go to the FTP sensor section in Circuit/System Testing.

  1. Install the fuel cap.
  2. With the engine running, the EVAP canister vent solenoid valve open, and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 12 inches H2O.
?‡'
If the fuel tank vacuum is greater than the specified range, go to the restriction section in Circuit/System Testing.



If

Sep 06, 2015 | Chevrolet Impala Cars & Trucks

1 Answer

Where is my vent valve solenoid on my 2006 Chevy Colbalt?


It's located under the vehicle back behind the fuel tank , Installed in the canister ! Remove the EVAP canister vent solenoid valve from the canister !
Rotate the EVAP canister vent solenoid valve counterclockwise in order to release it from the locked position.
Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle . Disconnect the evaporative emission (EVAP) canister harness electrical connector (2) from the EVAP vent solenoid valve. Clean away any debris that may be present around the EVAP canister vent solenoid valve.
Remove the EVAP canister bolt. Lower the EVAP canister.

Feb 25, 2015 | Chevrolet Chevy Cars & Trucks

1 Answer

I received the following code for a 2006 Saturn Ion with a 2.4 Litre motor P0446 what is is and how do I fix it?


Trouble Code: P0446

Evaporative Emissions (EVAP) Vent System Performance

Possible Causes:


The EVAP system tests run when the engine is first started and meets the Conditions for Running the DTC. An intermittent condition could be caused by a damaged EVAP vent housing, a temporary blockage at the EVAP canister vent inlet, or a pinched vent hose. A blockage in the vent system will also cause a poor fuel fill condition.An EVAP canister, vent hose, or vent solenoid valve that has restricted flow may cause this DTC to set. Using a purge solenoid command with a scan tool will allow vacuum to be applied to the system instead of pressure. With the engine running, the EVAP canister vent solenoid valve open and the EVAP canister purge solenoid valve commanded to 100 percent, the fuel tank vacuum should not increase to more than 5 inches H2O.An EVAP canister filter that is restricted can cause this DTC to set. Refer to Evaporative Emission (EVAP) Canister Filter Replacement and Evaporative Emission (EVAP) System Cleaning .Disconnecting one component at a time while the EVAP system is under flow will help to pinpoint a restriction in the system.Reviewing the Failure Records vehicle mileage since the diagnostic test last failed may help determine how often the condition that caused the DTC to be set occurs. This may assist in diagnosing the condition.For intermittent conditions, refer to Intermittent Conditions .

Dec 29, 2012 | 2006 Saturn ION

1 Answer

Auto scanner code 446


Here is the definition for a Blazer.

P0446 CHEVROLET Description The Evaporative System (EVAP) canister vent control valve is located on the EVAP canister and is used to seal the canister vent.


This solenoid valve responds to signals from the Engine Control Module (ECM). When the ECM sends an ON signal, the coil in the solenoid valve is energized. A plunger will then move to seal the canister vent. The ability to seal the vent is necessary for the on board diagnosis of other evaporative emission control system components.


This solenoid valve is used only for diagnosis, and usually remains opened.
Read more: http://engine-codes.com/p0446_chevrolet.html#ixzz2670glbIb

Sep 10, 2012 | 2004 Chevrolet Blazer

1 Answer

2004 niisan infinty g35x code p2135


NISSAN OBDII DTC

P1105 Manifold Absolute Pressure/Barometric Pressure Switch Solenoid Circuit

P1110 Intake Valve Timing Control Circuit (Bank 1)

P1120 Secondary Throttle Position Sensor Circuit

P1125 Tandem Throttle Position Sensor Circuit

P1132 Intake Valve Timing Control Position Sensor (Bank 1)

P1135 Intake Valve Timing Control Circuit (Bank 2)

P1137 Intake Valve Timing Control Position Sensor (Bank 2)

P1140 Intake Valve Timing Control Position Sensor (Bank 1)

P1145 Intake Valve Timing Control Position Sensor (Bank 2)

P1148 Closed Loop Fault Detected (Bank 1)

P1168 Closed Loop Fault Detected (Bank 2)

P1210 Traction Control System Signal Fault

P1220 Fuel Pump Control Module Fault

P1320 Ignition Control Signal Fault

P1335 Crankshaft Position Sensor Circuit

P1336 Crankshaft Position Sensor circuit

P1400 EGR/EVAP Control Solenoid Circuit

P1401 EGR Temperature Sensor Circuit

P1402 EGR System Fault Detected

P1440 EVAP Canister System Leak Detected

P1441 EVAP Vacuum Cut Valve Bypass Valve Circuit

P1443 EVAP Canister Control Vacuum Switch Circuit

P1444 EVAP Canister Purge Volume Control Valve Circuit

P1445 EVAP Purge Volume Control Valve

P1446 EVAP Canister Vent Valve Circuit

P1447 EVAP Canister Purge Flow/Volume Control Valve Circuit

P1448 EVAP Vent Control Valve Circuit

P1490 EVAP Vent Control Valve/Bypass Valve Circuit

P1491 EVAP Vacuum Cut Valve/Bypass Valve Circuit

P1492 EVAP Canister Purge Control Valve/Solenoid Valve

P1605 Transmission Control Module A/T Diagnosis Communication Line Fault

P1705 Throttle Position Switch Circuit

P1706 Park Neutral Position Switch Circuit

P1760 Overrun Clutch Solenoid Valve Circuit
P1900 Cooling Fan Control Circuit
sorry but your code reader is not reading manufacturers codes ,if an american market vehicle then you should be able to read them but if this is a europeon model then how did you manage to get this code??

P0235....Turbo/Super Charger Boost Sensor 'A' Circuit

this is a generic code if its any help

Nov 02, 2010 | 2004 Infiniti G35 Sport Coupe

2 Answers

I HAVEA 2006 CHEVERLET SUBURBAN 1500, AND THE CHECK ENGINR LIGHT STEAYS ON. THE CODE IS P0449; WHAT IS THIS AND WHERE IS IT LOCATED AT.


Hello. Your code indicates that your emission system is acting up. If you live in California, you might have a problem passing the next mandatory emmissions test. The PCM has determined that a malfunction exists in the electrical circuit for the vent valve/solenoid in the evaporative emission control system.

Definition:
EVAP (Evaporative Emission System) purge/vent solenoid circuit condition

Explanation:
The solenoids and system wiring are monitored for opens or shorts

Probable Causes
1- Purge or vent solenoids defective
2- Check connector and wiring
3- fuel, saturated vapor canister
4- Failed EVAP vent solenoid

Apr 08, 2010 | Chevrolet Suburban 1500 Cars & Trucks

1 Answer

My taurus failed due to code p0442 ecap emiss ctl sys leak detected (small leak)


    Continuous Memory Diagnostic Trouble Code (DTC) P0442 indicates that a fuel vapor leak has been detected [as small as 0.10 cm (0.04 inch)] in the Evaporative Emission (EVAP) system.
    Note: Prior to performing the following diagnosis inspect the Canister Vent Solenoid (CV) for contamination. A situation may exist where contamination holds open the Canister Vent (CV) solenoid enough to set DTC P0442 and also plugs the port to atmosphere enough to keep system from being vented quickly.
    • After market parts and accessories nonconforming to the EVAP system specifications.
    • Damaged, cross threaded or loosely installed fuel filler cap.
    • Small holes or cuts in fuel vapor hoses/tubes (EVAP canister tube, EVAP canister outlet tube or EVAP return tube) in the EVAP system.
    • Loose fuel vapor hose/tube connections to EVAP system components.
    • EVAP system component [EVAP canister purge valve, fuel tank pressure (FTP) sensor, canister vent (CV) solenoid, fuel vapor control valve tube assembly or fuel vapor vent valve assembly] seals leaking.
    • CV solenoid partially open when commanded closed.
    • EVAP canister leaking.
  • Check for presence of fuel filler cap.
  • Verify that the CV solenoid is properly seated on the EVAP canister (if possible).
  • Visually inspect for cut or loose connections to fuel vapor hoses/tubes in following locations:
    • EVAP canister to EVAP canister purge valve.
    • EVAP canister to fuel vapor vent valve assembly.
    • fuel vapor control valve tube assembly to fuel tank (if applicable).

Jun 26, 2008 | 1997 Ford Taurus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

102 people viewed this question

Ask a Question

Usually answered in minutes!

Top Saturn Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Saturn Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...