Question about Jeep Grand Cherokee

Open Question

Ignition lock cylinder, disassembel and reset tumblers.On a 2000 Jeep Grand Cherokee larado.

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: Ignition Key Doesn't Turn Sometimes in 2001 Jeep Grand Cherokee

test

Posted on Dec 22, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: 1996 Jeep grand Cherokee Larado, rear door stuck

go throu licence plate pannel pull up on bar and on the inside under ur pannel the nut fell off the mechanism so just put on a new nut

Posted on Feb 03, 2009

EnginEar

EnginEar

  • 57 Answers

SOURCE: 2001 Jeep Grand Cherokee. Malfunction light came on. What is the cause?

You can do one of three things.1. buy a scan tool 2. go to a dealer and pay to have the codes read and diagnosed 3. go to your local parts chain to have it read for free. (call first to verify). The code will tell you what system is malfunctioning and what the malfunction is. The parts store option is my choice, because you can also get the part to fix it if needed and you are not out the $ for diagnostics, nor did you need an appt to get it in.

Posted on Apr 26, 2009

maygemini

kris vis

  • 147 Answers

SOURCE: Radiator fan will not turn off in my 2000 Jeep Grand Cherokee

usually the engine relay or cooling fan relay..!

Posted on May 08, 2009

Robert Debison

  • 412 Answers

SOURCE: 2000 Jeep Grand Cherokee Laredo Door Locks Dont' Work Correctly

you need to check wiring between lf door and body..peel back rubber boot and pull on wires..you will find 1 or more broken wires..can be repaired

Posted on May 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i change ignition switch without the key on a 2000 jeep Grand Cherokee larado i lost the old key a brought a new ignition switch key


It's not too tough... But be careful ... First open and remove plugs... Then remove the chip from backside.... Now you can out..... Then do just opposite work for in...

May 16, 2015 | 2000 Jeep Grand Cherokee Laredo

1 Answer

Ignition switch for 2000 jeep grand cherokee is stuck


I'm going to answer this question since I don't know how the security system would affect the lock.
If you can get the key out of the lock, you may want to spray some WD40 or other lube in the slot where the key goes.
If that does not help, you should be able to drop the cover from under the steering wheel and disconnect the switch from the lock cylinder.
If the lock is still stuck, it may have damaged tumblers or something may be jammed with the shifter and steering wheel lock.

Dec 15, 2012 | 1999 Jeep Grand Cherokee

1 Answer

Steering wheel locked and key will not turn 2000 jeep grand cherokee


First thing you need to try is wiggling the steering wheel back and worth while turning the key to try and unlock the steering column. If the key is worn out it may not turn well in the ignition. Another thing is to lubricate the ignition cylinder. If nothing works, it maybe the ignition cylinder tumbler is worn out and needs to be replaced.

Feb 24, 2011 | 2000 Jeep Grand Cherokee

1 Answer

Jeep - can't turn ignition key


your ignition barrell tumblers are getting stuck, you need to replace the barrell and tumblers at dealership. you can get the key to turn if you hold key in ignition and try and turn and at the same time tap the end of the key which normally jogs the tumblers to enable key to turn

Jun 01, 2010 | 2000 Jeep Grand Cherokee

1 Answer

I have a 1999 Jeep Grand Cherokee. The vehicle


sounds like the key is either worn down to where the ridges in the key wont push the tumblers inside the key lock cylinder into their proper place to move the cylinder into the starting position. Or your steering colum is locked and the wheel is moving freely as if it were not. So your solution would be to either have an expert look at it (estimated cost: 200$ low/400$high) or you can attempt to fix it yourself.
should you choose the "I'll fix it myself" method....try getting a new key made at a hardware store since keys wearout over time (ie:10years of turning that old key), this may solve the problem right away if the ridges are just worn on the key. Or the hard way, you need to get a phillips screwdriver and some jewelers tools and an 8mm or 10mm wrench/rachet+socket to disconnect the battery, then underneath the steering colum just under the ignition is a hole in the colum shroud/cover, from there you can disconnect the ignition key lock cylinder (the thing you put your key into). once you've removed the cylinder from the steering colum you should test your key again to see if you can turn the cylinder outside of the colum if you cannot then buy a new ignition key lock cylinder for about 15$-30$...problems solved.

Nov 18, 2009 | 1999 Jeep Grand Cherokee

1 Answer

Key won't turn


The key problem could be a worn out key that is not disengaging the tumblers in the ignition switch or tumblers that are sticking(squirt a little wd40 in the ignition cylinder and move the key in and out a couple of times) inside the switch. Make sure the shifter is fully in park.

Mar 01, 2009 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

53 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...