Question about Ford Ranger

1 Answer

How to remove horn cover on 86 ford ranger--did remove lower 2 screws--upper 2-??

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 14,092 Answers

You have to turn steering wheel to remove top screws.

Posted on Apr 04, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: 86 ford ranger

its under the carpet on the passanger side at the firewall

Posted on Jul 21, 2008

Anonymous

  • 1 Answer

SOURCE: R/R horn for 2000 Ford Ranger

Since I never got a RESPONSE!!!! I rewired the horn to a different location and attached a ground wire.

Posted on Nov 13, 2008

Anonymous

  • 235 Answers

SOURCE: Replace thermostat in 2000 ford ranger

the open pipe that you took the hose off of is the thermostat housing, you will need to remove this to reveal the thermostat, make sure you use a new gasket with sealant when reinstalling thermostat housing to prevent leaks and dont over tighten the bolts,run both bolts down as far as you can before final tightning

Posted on Dec 26, 2008

Anonymous

  • 8 Answers

SOURCE: upper & lower Ford Ranger ball joints replacement

that sounds pretty high, I had those replaced on my 99 ranger XLT and it only cost me $400.oo, in Naples, FL. Id definately shop around.

Posted on Jan 25, 2009

greg_margo

Greg Margossian

  • 1959 Answers

SOURCE: CD stuck in 2006 Hyundia Tucson -How do you remove the CD/radio?

Answered a similar problem last week. Disconnect the negative battery cable for 10min. When you re-connect, the stero should reset and you should be able to get the CD out. If this works, will save you a lot of aggravation without having to remove the stereo. Best of luck!
Greg

Posted on May 18, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing steering column shroud on a 2006 sierra 3500, no screws where videos show to remove them there's a recess area but no screws in the locations indicated


Steering Column Trim Cover Replacement

Important: You must check for 2 pan head tapping screws (1,2) in the lower trim cover before removal.
If necessary, remove the 2 pan head tapping screws (1,2) from the lower trim cover (3). Remove the lower trim cover (3).
If screws are not present in the lower trim cover, proceed to the next step.
Gently unsnap the lower trim cover from the upper trim cover.

Important: You must check for 1 TORX® head screw (1) in the upper trim cover (2) before removal.
If necessary, remove 1 TORX® head screw (1) from the upper trim cover (2).
If a screw is not present, remove the upper trim cover (2).

Dec 01, 2016 | 2006 GMC Sierra 3500

1 Answer

How do I change the shift interlock actuator on a 99 ford ranger?


Remove the steering column's upper and lower covers. Then remove the shift cable from actuator and then remove the electrical connector and then remove the screws to remove the actuator from the steering column.

Feb 25, 2015 | Ford Cars & Trucks

1 Answer

Where Is the anti theft module


Passive Anti-Theft System (PATS) Transceiver module is around the key lock cylinder behind or under the plastic cover on the upper steering column'
Passive Anti-Theft System (PATS) Transceiver Removal
  1. s4h~tr~en~file=ani_caut.gif~gen~ref.gif CAUTION: Electronic modules are sensitive to electrical charges. If exposed to these charges, damage may result.
    Disconnect the battery ground cable, Refer to Section 414-01
  1. Remove the ignition switch lock cylinder.
    1. Insert the ignition key into the ignition switch lock cylinder and turn to the RUN position.
    1. Push the ignition switch lock cylinder release tab with a punch while pulling out the ignition switch lock cylinder.
    2. If equipped, remove the tilt wheel handle.
    3. Remove the upper and lower steering column shrouds.
      1. Remove the screws.
      1. Remove the upper and lower steering column shroud.
      2. Remove the lower instrument panel steering column cover.
        1. Remove the screws.
        1. Remove the lower instrument panel steering column cover.
        2. Remove the instrument panel steering column opening cover reinforcement.
          1. Remove the bolts.
          1. Remove the instrument panel steering column opening cover reinforcement.
          2. Remove the anti-theft transceiver module.
            1. Remove the screw from the bottom of the transceiver module.
            1. NOTE: Only apply pressure or leverage below the key cylinder lower rib.
              Disconnect the electrical connector and remove the module.

Dec 24, 2014 | 2006 Ford Taurus

1 Answer

Highbeam switch


  1. If equipped, disable the SIR system. Disconnect the negative battery cable.
  2. Remove the upper steering column cover.
  3. Remove the lower steering column cover screws and lower the steering column cover.
  4. Remove the 2 switch mounting screws and remove the switch.
  5. Detach all wire connectors from the combination switch. Push locking tabs to remove the wires.

To install:

  1. Attach all wire connectors to the combination switch.
  2. Install the combination switch to the column with the 2 attaching screws.
  3. Install the lower steering column cover screws and lower steering column cover.
  4. Install the upper steering column cover and attaching screws.
  5. Connect the negative battery cable.
  6. Enable the SIR system, if equipped.

Dec 04, 2011 | 1999 Pontiac Sunfire

1 Answer

How do i remove the turn signal switch on a 2001 chevy impala


Removal & Installataion
  1. Verify that the multifunction turn signal lever is in the center of the OFF position.
  2. Disconnect the negative battery cable.
  3. Disable the SIR (air bag) system. Refer to the Chassis Electrical Section.
  4. Remove the air bag module from the steering wheel.
  5. Remove the steering wheel.
  • Remove the upper and lower steering wheel trim covers using the following procedure.
    • Remove the tilt lever assembly.
    • Remove the two pan head tapping screws from the lower shroud.
    • Unlock the upper and lower shroud.
    • Remove the two Torx® head screws from the upper shroud.
    • Remove the upper shroud.
  • Remove the wire harness straps from the wire harness assembly and detach the wiring harness connectors from the switch side connectors.
  • Remove the two multifunction turn signal switch screws and remove the multifunction switch assembly from the vehicle.
  • To install:
    1. Install the multifunction switch to the steering column. Use a small flat-blade prytool to compress the electrical contact and move the multifunction turn signal switch into position. Verify that the electrical contact rests on the canceling cam. Install the screws and tighten to 62 inch lbs. (7 Nm).
    2. Route the wire harness along the steering column jacket assembly and secure into the wire harness strap. Install a new wire tie to the upper tilt head assembly and another lower along the wiring harness, as the original installation.
    3. Verify that the lever is in the center of the OFF position.
    4. Install the upper and lower steering column shrouds.
    5. Route the SIR connector through the steering wheel, align the scribe mark on the steering wheel made at removal, with the slash mark on the steering shaft and install the steering wheel. Install the steering shaft nut and torque to 30 ft. lbs. (41 Nm).
    6. Install the horn contact leads and the air bag connector to the back of the air bag. Make sure the CPA wedge is in place to secure the connector. Install the air bag by gently pushing on both the right and left sides of the air bag until the retaining springs engage.
    7. Enable the SIR system by connecting the yellow 2-way connector at the base of the steering column and installing the air bag fuse.
    8. Connect the negative battery cable. Test the horn, turn signals and headlight operation.

    Mar 06, 2010 | 2001 Chevrolet Impala

    1 Answer

    How to replace the rear bumper cover on a Chrysler Pacifica


    1. Open liftgate. 2. Remove both taillight assemblies by removing 2 hex-head bolts located in the area revealed when the liftgate is opened. 3. Remove 4 plastic retainers on the very bottom of the bumper cover in the rear. 4. Remove 2 phillips head screws in the wheel well rear lip. 5. Remove 4 pop-up plastic retainers in liftgate area. Use two screw drivers to lift the head and then pull the entire retainer out. 6. Remove a hex-head bolt from each side in the area revealed when the taillight assembly was removed. 7. Bend the bumper cover outward on each side to clear the wheel well lip and remove the bumper. Have a blanket or carpet on the ground to protect the bumper. 8. Remove metal clips from tabs that connect the upper bumper cover to the lower bumper cover. 9. Drill out pop-rivets that connect upper bumper cover to lower bumper cover. 10. Push tabs out of slots to separate the upper and lower bumper covers. 11. Release tab locks on chrome trim pieces and remove from upper bumper cover. 12. Reverse this process to replace the bumper cover.

    Feb 16, 2010 | 2006 Chrysler Pacifica

    1 Answer

    How hard is it to put in an ignition in a 89 ford probe gt turbo?


    This is what it looks like to replace it....you decide on what your level of mechanical knowledge is. I hope this helps you!

    Removal & Installation
    1. Disconnect the negative battery cable.
    2. Remove the lower instrument cluster cover as follows:
      1. Remove the steering wheel. Refer to Section 8.
      2. Remove the 2 column cover screws and the cover.
      3. Remove the 9 cluster module mounting screws.
      4. Carefully pull the cluster module outward and disconnect the electrical connectors.
      5. Remove the ignition switch illumination bulb and remove the cluster module.
      6. Loosen the 2 cover hinge screws and the 6 upper cluster cover screws. Remove the cover.
      7. Remove the lower cluster cover panel.
    3. Remove the lap duct and the defrost duct.
    4. Remove the mounting nuts from the hinge bracket.
    5. Remove the steering column upper mounting bolts/nuts and allow the steering column to hang down.
    6. Remove the screw securing the ignition switch to the ignition switch housing.
    7. Disconnect the 4 ignition switch snap connectors located to the left of the steering column.
    8. Remove the protective looming from the ignition switch wires.
    9. Note the position of each wire in the 4-terminal connector for installation reference. Disconnect the 2 wires (green wire and red wire/orange tracer) of the key-in warning buzzer at the 4-terminal connector by disengaging the tang with a paperclip or other suitable tool.
    To install:
    1. Connect the 2 wires of the key-in warning buzzer to the 4-terminal connector as follows:
      1. Align the flat side of the wire end with the grooved portion of the connector.
      2. Push the wire into the connector until the locking tang engages the end of the wire.
    2. Install the protective looming around the ignition switch wires.
    3. Connect the 4 snap electrical connectors of the ignition switch to their mating connectors, pushing together until the locking tangs are in place.
    4. Install the ignition switch into the switch housing and secure it with the screw.
    5. Raise the steering column into position. Install the upper bracket bolts and tighten to 12-17 ft. lbs. (16-23 Nm).
    6. Install the cluster support nuts and tighten to 6.5-10 ft. lbs. (8.8-14 Nm). Install the hinge bracket nuts and tighten to 12-17 ft. lbs. (16-23 Nm).
    7. Install the lap duct and defroster duct.
    8. Install the lower cluster cover panel and the cluster cover.
    9. Install the ignition switch illumination bulb. Connect the electrical connectors and install the cluster module with the attaching screws.
    10. Install the column cover and the steering wheel.
    11. Connect the negative battery cable and check ignition switch operation.
    3efa4d6.gif
    Ignition switch removal and installation—1989 Probe

    Nov 19, 2009 | 1989 Ford Probe

    1 Answer

    How to change coil spring on 1994 ford ranger


    RAISE AND SAFELY SUPPORT VECHICLE.PLACE A SUPPORT UNDER THE REAR AXLE.REMOVE NUTS AND BOLTS ATTACHING THE SHOCK ABSORBER TO THE RADIUS ARM.REMOVE THE NUT SECURING THE SPRING TO THE AXLE AND REMOVE THE RETAINER.SLOWLY LOWER THE AXLE TO RELIEVE THE SPRING TENSION.REMOVE THE SPRING BY ROTATING THE UPPER COIL OUT OF THE TABS IN THE UPPER SPRING SEAT - TO INSTALL.INSTALL. THE TOP OF THE SPRING IN THE UPPER SEAT.ROTATING INTO POSITION.RAISE THE AXLE UNTIL SPRING IS SEATED IN THE LOWER SPRING SEAT.INSTALL THE LOWER RETAINER AND TIGHTEN THE NUT TO 70 - 100 FT LBS .THEN CONNECT THE SHOCK ABSORBER TO THE RADIUS ARM AND LOWER THE VECHICLE.

    Aug 01, 2009 | 1994 Ford Ranger Supercab

    1 Answer

    Want to replace left power mirror on a 2004 ford ranger. Not sure


    unscrew 2 screws in black plastic handle, remove black plastic but do not unplug if electric windows look in lower rear corner remover one screw there and one screw behind the black plastic handle and if hand crank windows pull not to hard and separate window crank and find a phillips or torx screw in the but have window down and gentle get fingers on lower sind of door panel and slide upwards towards the sky and it shoud come off

    Dec 11, 2008 | 2004 Ford Ranger

    2 Answers

    Ball joints???


    You're not supposed to replace the uppers on a 98 ranger. They're not meant to be pressed out because its built in with the control arm as a single unit. Just buy new upper control arms and save yourself the trouble. Ford also claims you have to replace the control arm for the lowers as well, but that's BS. They can be replaced fairly easily with the proper tools.

    Jul 17, 2008 | 1998 Ford Ranger SuperCab

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    60 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Ford Experts

    Marvin
    Marvin

    Level 3 Expert

    85206 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22484 Answers

    gerry bissi

    Level 3 Expert

    4388 Answers

    Are you a Ford Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...