Code P0366 showing up. I already replaced the one sensor
There are a few thing which can cause the code. here is some info and some ideas, and locations.
https://www.obd-codes.com/p0366
https://www.autocodes.com/p0366.html
https://www.yourmechanic.com/article/p0366-obd-ii-trouble-code-camshaft-position-sensor-b-circuit-range-performance-bank-1-by-valerie-johnston
https://www.youtube.com/watch?v=-UCjHpnuUKw
https://www.youtube.com/watch?v=39rHOq0XwZo
https://www.youtube.com/watch?v=WPp4VoLPEKg
https://www.youtube.com/watch?v=oxzDbPWueIo
https://www.youtube.com/watch?v=dOvwSncdP0g
https://www.youtube.com/watch?v=YK4f96ZzJGs
SOURCE: P0340 Code Camshaft Position Sensor
The Camshaft Position (CMP) Sensor detects the position of the camshaft in order to identifiy when piston No. 1 is on its compression stroke. The CMP sensor is used for ignition timing in the Ford DIS igntion system, but not in the EDIS igntion system. Both DIS/EDIS use the CMP signal for synchronizing the firing of sequential fuel injectors.
On the 3.0L vulcan engine, the CMP signal is generated by a single Hall-Effect magnetic switch, activated by a single "vane" spinning around by virture of a synchronized shaft which is driven by the camshaft.
The CMP sensor & synchronizer/shaft are located behind the intake manifold (i.e., back near the firewall on a Ranger) on the top of the cylinder block. If you just need to replace the sensor, it is a simple job of unplugging the electrical connector and removing the screws holding the sensor in place. Here is a sketch of the sensor to give you an idea what to look for:
SOURCE: replacing bad camshaft position sensor
Reverse procedure to install and prior to installing new sensor, lubricate sensor O-ring.
It is located under the water pump. Make sure when you remove the sensor that you rotate the crank shaft and look in the hole to make sure the pick up magnet is still in there. Sometimes they come loose and cause a no start or long crank. You will need to have the code cleared still.
SOURCE: Camshaft position sensor replacement for 2002 Audi A4
its not hard to fix.but you going to have to move some things to get to it. you will need a haynes repair manual.it will show you photos and instructions how to replace it.
SOURCE: where is the Camshaft Position Sensor located on a
this car has but one bank, the cam sensor is under the intake manifiold on the drivers side.
Testimonial: "thanks, now I know where to start looking. Is it a fairly easy item to replace?"
SOURCE: I have a P0011 "Camshaft Position/Bank 1 code.
OK check the CMP sensor connector for cleanliness, sometimes oil can get in and disrupt the signal transmission to the ECU. Check the wire loom continuity all the way back from the CMP to the ECU. If the error code persists remove the cam sensor, clean its tip of any debris and refit.
Testimonial: "Thanks joe2mercs...you had the problem diagnosed correctly. Cleaned and light has not come back on. U saved me a lot of $."
?€¢
Observe the scan tool CMP Desired, Actual, and Angle Variance parameters before a DTC sets. This may help to isolate whether a condition is specific to one camshaft, one bank, or caused by a condition with the primary crankshaft timing.
DTC Descriptors
DTC P0010: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1
DTC P0013: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 1
DTC P0020: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2
DTC P0023: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Bank 2
DTC P2088: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1
DTC P2089: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1
DTC P2090: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 1
DTC P2091: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 1
DTC P2092: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2
DTC P2093: Intake Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P2094: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit Low Voltage Bank 2
DTC P2095: Exhaust Camshaft Position (CMP) Actuator Solenoid Control Circuit High Voltage Bank 2
DTC P0341: Intake Camshaft Position (CMP) Sensor Performance Bank 1
DTC P0342: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1
DTC P0343: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1
DTC P0346: Intake Camshaft Position (CMP) Sensor Performance Bank 2
DTC P0347: Intake Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2
DTC P0348: Intake Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
DTC P0366: Exhaust Camshaft Position (CMP) Sensor Performance Bank 1
DTC P0367: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 1
DTC P0368: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 1
DTC P0391: Exhaust Camshaft Position (CMP) Sensor Performance Bank 2
DTC P0392: Exhaust Camshaft Position (CMP) Sensor Circuit Low Voltage Bank 2
DTC P0393: Exhaust Camshaft Position (CMP) Sensor Circuit High Voltage Bank 2
I'm sorry but when dealing with these problems your best bet is to take your vehicle to a qualified repair shop , I have never see a DIY'ER correct the problem with these , an in the end always end up taking it to the dealer .
P0010....'A' Camshaft Position Actuator Circuit (Bank 1)
P0011....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
P0012....'A' Camshaft Position - Timing Over-Retarded (Bank 1)
P0013....'B' Camshaft Position - Actuator Circuit (Bank 1)
P0014....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 1)
P0015....'B' Camshaft Position -Timing Over-Retarded (Bank 1)
P0020....'A' Camshaft Position Actuator Circuit (Bank 2)
P0021....'A' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)
P0022....'A' Camshaft Position - Timing Over-Retarded (Bank 2)
P0023....'B' Camshaft Position - Actuator Circuit (Bank 2)
P0024....'B' Camshaft Position - Timing Over-Advanced or System Performance (Bank 2)
P0025....'B' Camshaft Position - Timing Over-Retarded (Bank 2)
I think your sensors are pattern parts and the readings /resistances are not the same as the original parts ,try some bosch units is my first suggestion ,
2,845 views
Usually answered in minutes!
×