Removing the trim panel does not expose mounting screws for the control unit
SOURCE: Door Panel Removal -2001 Dodge Caravan
to be honest about it I always pry it out enough to get my fingers behind it to get a grip and **** as hard as i can to get it loose i believe the 2001 has the two piece clips that are tough to get to let go and the clips usually break very rarely the panel will id say like 1 in 75 and there are so many clips you cant tell if one is missing
SOURCE: Buick LeSabre left front window will not close
Don it. Good half day for amateur. Get Chilton 86-99 Bonneville, 88, Lesabre manuel.. Tricky to find bolts are under end flaps on door close handgrips. Took me a day to figure that one out. Others under light at lip of back of door. Book indicates to strart with window 3/4 up if you can. Flip up window control at rear of panel. After all screws are out raise outer edge of armrest and look for notches 4" and 11-1/2" from rear of armrest to slide inward to remove. There are screws under the door handle too. Screws everwhere. When pulling bottom of panel from door lift with a notched bar to avoid tearing the fasteners out of the cardboard panel. Two screws behind seatbelt notch at top need to come out to allow positioning the glass. The panel at the bottom of the top opening can be removed for more fredom in positioning the glass when reinserting the ball in the lower track on the window. Tape glass with duct tape to keep it from falling. Drill the factory rivets that hold the old regulator and I replaced with stove bolts with nylon locknuts slotted head to the inside the car. Can't remember the size, probably 1/4 or 3/16". Remove speaker if in front bottom of door to use your hand to do work in the door. You must twist the regulator forward with window 1/2 down to remove the ball from the socket in the bottom sliding metal track at the bottom of the window. Don't drop the window after removing the socket, tape it in place. Don't know what you do if you cannot move it to 1/2 up position. By the way, the body shops say you must use rivets, not screws or it will shift, but I have had no problems with the screws for reinstallation several years old. The rivet they use take a big hydraulic pop rivet gun that you won't have. Good luck, I don't envy you. Need to do other window on my 91. The window control may not be the same on the Custom, mine is the Ltd. you may be able to remove the motor from the regulator in the door without removing the regulator if you can figure out how to get the bolts that hold the moter to the regulator. inside the door.
SOURCE: How do I remove the front door panel to replace the mirror
Normal
0
Disconnect your negative battery cable. Locate and remove
the screws that hold your interior door handles in place (they may be hidden by
snap in, or snap on clips). Remove the interior door handles, then disconnect
the wire clips to the switches. Your panel is held in place by snap in clips;
use a small pry bar to pull them from the door (try to get as close to, or
directly under the clips to prevent them from tearing out of the door panel).
Once the clips are pulled, pull the panel upward to remove it from the door.
Install in reverse.
If you don't have power windows you will have to
remove the manual window crank. It is held in place by a clip on the back side
of the base. To remove the clip, you will need a small hook (kind of like a
knitting needle). Put the hook in behind the base, and grab the clip and pull
it off. To replace it, slide the clip back on the window crank, and snap it
back on the door.
SOURCE: REPLACEMENT OF [LOW BEAM] HALOGEN BULB IN 2004 Buick LeSabre
I just Replaced a Low Beam Light bulb on a 2005 Buick La Sabre.
If You use a Metric socket and Remove the Two Silver bolts Attaching the headlight Assemble onto the metal surrounding the the lamp assembly it comes out to the front. This makes it much easier to access the bulb. Twist it counerclockwise & it comes out by pulling gently on the bulb. Then by realeasing a tab that is the socket holder bulb can be removed & replaced with a New #9006 low beam halogen light bulb. Wrap a Paper towel around the bulb & do NOT touch it with your bare hand as this wiil ruin a halogen bulb,
SOURCE: 99 Buick LeSabre, how do I remove driver side door panel to replace power window motor?
You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. You'll need to lift the door panel upwards in order to get it off the window ledge. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door
To install:
95 views
Usually answered in minutes!
×