Question about 2008 Chrysler Pt Cruiser

1 Answer

2008 Chrysler PT Cruiser replaced aircon, power steering belt,now aircon not working since.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 22,484 Answers

Have you damaged the wires on the AC pump or knocked the plug out .

Posted on Feb 24, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

francis rivero

  • 958 Answers

SOURCE: Replacing Alternator For 2001 Chrysler PT Cruiser (Manual)

this instruction is general for all vehicles. i am sorry that i do not have particularly for your 2001 chrysler PT cruiser.

first, identify the alternator.
remove the fan belt on the alternator,
label and remove all wires that is attached to it.
remove all bolts that is holding it.
remove the old alternator.

do the reverse on installing it.

tnx 4 using fixya,

drcool

Posted on Aug 30, 2008

justuscc

Jimmy

  • 360 Answers

SOURCE: power steering fluid PT Cruiser

power steering fluid or dextron 3 trans fluid

Posted on Oct 10, 2008

66 chrgr

mike loshbough

  • 1011 Answers

SOURCE: where is the crank sensor located on 2005 chrysler pt cruiser?

the crank sensor is located on back right side of engine by were the trans. bolts up.is the no start when could or hot?

Posted on Jan 25, 2009

localwonder

Michael Masters

  • 6784 Answers

SOURCE: Change the thermostat on 2002 Chrysler PT Cruiser

Hi, i have put together a step by step guide that will help you with this replacement job. Make sure the vehicle is in a cool state before starting this job.


* Drain some coolant into a clean container until the coolant level is below the thermostat housing.
* Remove the upper radiator hose connection from the thermostat housing.
* Loosen the housing bolts and remove the housing.
* Remove the gasket and scrape it carefully from the surface of the housing and the mounting surface on the engine. If the gasket remains on either of the surfaces, there will probably bea coolant leak after reassembly. Some engines use a rubber O-ring to seal a thermostat housing.
* Compare the size of the thermostat to the old one. They are of different sizes, types, and temperature ratings.
* The temperature rating is stamped on the sensing bulb on the bottom of the thermostat. The temperature bulb faces the block.
* When replacing a thermostat, be sure that the thermostat fits into the groove in the block or outlet housing. If the thermostat is installed upside down, the engine will overheat.
* Install the gasket.
* Reinstall the thermostat housing. Refill the system and run the engine or pressure test to check for leaks.
* When the engine has reached operating temperature make sure the thermostat opens.
* You should be able to see coolant circulating within the radiator.
* Another way of checking thermostat operation is to feel the top of the radiator hose or use a thermometer or multimeter with a temperature probe to confirm that the coolant is warming up.
* If the engine is overheating, but the top hose is still cool to the touch, the thermostat is stuck closed and must be replaced.

NOTE
When a paper gasket is used and the recess is in the thermostat housing, it is a good practice to position the thermostat into the recess and glue the gasket to hold it in place. If it falls out of its groove during installation, the outlet housing can be cracked or a coolant leak will result. Before tightening the water outlet housing, try to rock it back and forth to be sure it is flush. Housings are often cracked during this step.


9c06de2.jpg

Posted on Apr 30, 2009

Anonymous

  • 60 Answers

SOURCE: my 2002 pt cruiser lost power steering suddenly

check to see if the serpantine belt is still there. It sounds like like it broke. this belt runs all of the accesories on the vehicle including the water pump. So if this happened it probably starting running hot too

Posted on Jun 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where can I get a belt installation diagram?


Diagrams here, this may help you. Belt diagrams are at bottom of page, after timing belt diagrams. http://www.2carpros.com/diagrams/chrysler/pt-cruiser/2001

Nov 07, 2015 | 2001 Chrysler PT Cruiser

1 Answer

My belt came off of my power steering unit on my 2001 pt cruiser. if i drive my car will it cause any xtra damage.


From the looks of the diagram it does run the water pump as well so unless you want to replace the head i would park it.

Jul 17, 2014 | 2001 Chrysler PT Cruiser

1 Answer

Lenghth of a powrr steering and ac belt


Return to the parts store and have them confirm that it is correct. Sometimes their catalog listings are incorrect. Could you possibly show them the old belt?

Jan 12, 2014 | 2002 Chrysler PT Cruiser

2 Answers

2008 pt cruiser - check engine light came on, within minutes it started to "power down" and and died. Won't start. What could cause this? BTW have changed spark plugs, camshaft sensore, cranks


My PT did that when my timing belt broke. It cost $500.00 to replace it. If it is broken, be ready to have some motor work done. I had to have to values replaced at a cost of $900.00. If your timing belt is not broken then check the alternator and battery. I was riding down the road and my PT shut all the way down and would not start. I had to leave it beside the road. It was my alternator. It gave me no warning.

Dec 04, 2012 | 2008 Chrysler Pt Cruiser

1 Answer

My 2002 pt cruiser lost power steering suddenly


check to see if the serpantine belt is still there. It sounds like like it broke. this belt runs all of the accesories on the vehicle including the water pump. So if this happened it probably starting running hot too

Jun 23, 2009 | 2002 Chrysler PT Cruiser

1 Answer

Power steering not working


check power steering belt may be broken then get back to me. Good
luck

Jan 02, 2009 | 2002 Chrysler PT Cruiser

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

62 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...