Question about Cars & Trucks

1 Answer

My problem is the passenger window only opens halfway doesn't fully open , also when opening the door the window doesn't drop to allow for opening sometimes

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Loyalty:

    Visited the website for 30 consecutive days.

  • Cars & Trucks Master
  • 613 Answers

Problem with the window actuator, most likely the wires are frayed so would need renewing, strip out door panel and inspect

Posted on Feb 10, 2019

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
short shadey

jeff r

  • 421 Answers

SOURCE: Front passenger door won't open.

you may need to get a slim jim to open the door to make the repairs -jeff please rate

Posted on Sep 05, 2008

alantmorris

  • 4 Answers

SOURCE: drivers window doesnt drop on 2003 tt roadster,when opening door

ignition on
windows all the way down
windows allthe way up, let go of switches
push them up again and hold for 3-5 seconds
ignition off

Posted on Dec 16, 2008

Anonymous

  • 89 Answers

SOURCE: no dome light when passenger door open

Since the passenger door doesn't get used as much as the drivers door, check to see if the switch is not just stuck. It is a little button with a spring that opens up and turns the light on. It is located on the hinge area of the door and when the door closes it shuts off the switch, if it is not stuck then I would suspect said switch.

Posted on Jan 09, 2009

Anonymous

  • 64 Answers

SOURCE: 2002 taurus passenger door lock

Mine did this. I went around to each door and sprayed a liberal amount of WD-40 in the latch, then open and closed each door about five times. It hasn't done it since. I think the switch inside was not moving freely.


Posted on Jan 16, 2009

fusster

  • 65 Answers

SOURCE: window wont auto lower or rise to open door

my guess is the door lock mechanism is faulty.if the window control unit does not see a signal for the door being opened it will not raise or lower the window...does the interior light opperate when the door is opened???.if not you can put money on it being the mechanism.

Posted on Feb 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2008 pontiac g6 drivers window, when handle is lifted the window does not drop the inch or so that it should.


The window indexing feature is used to lower the driver and passenger power windows approximately 4 mm when the door is opened. This is necessary to allow the top edge of the window to clear the window weather-strip. This feature will also raise the window to the fully seated position once the door is closed.
Is just the driver door not working ?
Observe the operation of the driver window and front passenger window while opening and closing their respective doors. The windows should index DOWN and UP when the doors are opened and closed.
? If either window does not index UP or DOWN, refer to Window Index Feature Malfunction.

Window Index Feature Malfunction
Ignition ON, observe the scan tool Driver Door Ajar Sw and Door Ajar Switch parameters while opening and closing the driver and passenger doors, the parameter should change from Door Closed to Door Ajar.
? If the parameter does not change when opening and closing the doors, refer to Door Ajar Indicator Malfunction .
Ignition OFF, disconnect the harness connector at the appropriate window motor.
Ignition ON, with the door closed, test for greater than 10 volts between the signal circuit terminal 5 and ground.
? If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM.
With the door open, test for less than 1 volt between the signal circuit terminal 5 and ground.
? If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the BCM.
If all circuits test normal, replace the window motor.

Your best bet mite be to take your vehicle to a qualified repair shop (GM dealer )

Nov 13, 2017 | Pontiac Cars & Trucks

1 Answer

How to reset windows on is 350 lexus 2007


(a) Turn the engine switch on (IG).

(b) Halfway open the power window by pressing the power window switch.

(c) Fully pull up the switch until the power window is fully closed and continue to hold the switch for approx. 1 second after the power window is fully closed.

(d) Check that the AUTO UP/DOWN function operates normally.

If the AUTO UP/DOWN function operates normally, reset operations have been completed at this time. If not normal, follow the steps below.

(1) Disconnect the negative battery terminal for 10 seconds.

(2) Connect the battery terminal.

(3) Turn the engine switch on (IG).

(4) Halfway open the power window by pressing the power window switch.

(5) If the AUTO UP/DOWN function operates normally, reset operations have been completed at this time.

If not normal, follow the steps below.

(6) Turn the engine switch on (IG).

(7) Halfway open the power window by pressing the power window switch.

(8) Fully pull up the switch until the power window is fully closed and continue to hold the switch for approx. 12 seconds after the power window is fully closed.

(9) Check that the AUTO UP/DOWN function operates normally.

Feb 05, 2017 | 2007 Lexus IS 350

1 Answer

Why does the power window button blink on and off and the automatic feature doesn't work in the 2008 Toyota Sienna?


NOTE:
Anytime the batteryterminal has been disconnected, please initialize the driver's door power windowand front passenger's door power windowafter reconnecting the batteryterminal.

With ignition switchin the "ON" position, do the following:

1. Push down and hold the driver's door power windowswitch to completely open the window.
2. Pull and hold up the driver's door power windowswitch until the window closes.

Continue holding the switch for approximately one second until the switch changes from blinking to a constant illumination.
3. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

At this time the power window switchfor the passenger's door windowshould be blinking.
4. Push down and hold the passenger's door power windowswitch to completely open the window.
5. Pull and hold up the passenger's door power windowswitch until the window closes.
Continue holding the switch for approximately one second until the switch changes
from blinking to a constant illumination.
6. Check for proper operation of the "one-touch open and close" function by fully pushing the switch briefly to the "DOWN" and "UP" positions.

Feb 09, 2016 | Toyota Cars & Trucks

1 Answer

How do I get the external passenger door handle to engage the mechanism to open the door.


May be a control rod has dropped off. Remove the inner door handle and the inner cover , wind up the window . remove the plastic dust seal, you will now be able to inspect the door lock.

Apr 28, 2015 | Cars & Trucks

1 Answer

Fix for the door glass,2009 CHALLENGER. Won't reset to down position when opening door to allow window to break seal.Then move up and seal glass when door is closed. SMart Glass?


This may be as simple as relearning the window stop positions. Perform the following procedure to relearn the windows;

1) Sit in the drivers seat and ensure both doors are fully closed.
2) Turn the key to the ON position but do not start the vehicle.
3) Pull up on the drivers window switch until the window reaches the full up position, then CONTINUE HOLDING THE SWITCH UP for 2-5 seconds, then release the switch.
4) Push down on the drivers window switch until the window fully opens, then CONTINUE HOLDING THE SWITCH DOWN for 2-5 seconds, then release the switch.
5) Repeat steps 1-4 for the passenger window.
6) Close both windows and check the operation of the smart glass.

Let me know if you need further help.

Nate

I’m happy to assist further over the phone at https://www.6ya.com/expert/nathan_cc888cf971f43e78

Oct 18, 2014 | 2009 Dodge Challenger

1 Answer

How do i reprogram the power sliding door on a 2005 buick terraza


From the owner's manual:

If your vehicle has

the dual power sliding doors, both doors will have

to be reset. To reset a door, do the following:

1. Check to be sure the power sliding door is

unlocked and securely closed.

2. Turn the ignition to LOCK.

3. If the power sliding door overhead console

switch is in the override (deactivation)

position, return to the activation position.

4. Open the sliding door using the remote

keyless entry transmitter, overhead console

switch, or passenger switch. Allow the door to

travel fully open.

If the door does not travel to the fully open

position, press the overhead console switch to the

override (deactivation) position and slide the

door fully open and closed. Check for foreign

objects in the tracks. Repeat the procedure starting

with Step 1. If the door resists travel to the fully
open position, see your retailer for service.

Dec 27, 2012 | 2006 Buick Terraza

1 Answer

Passenger inside door handle is stuck halfway out.can't unlock or


gear on door handle prob stripped.. get new handle and install their around 20 dollars

Mar 06, 2010 | 1998 Ford Explorer

1 Answer

2003 BMW 330CI convertible frt. passenger window does not retract


the problem is in the door lock and the assemble must be changed. when one looks in the catch which look the door you will see a white switch in the lock and this the defect. the switch is built in the lock.

Jul 20, 2009 | 1997 BMW 328

2 Answers

Malfuntioning driver's side power window upon opening door lever.


get it to the dealer asap.

you definitely need to take apart the door. There's something not right inside.

May 24, 2009 | 2002 Porsche 911

3 Answers

Rear passenger side door will not open


the problem would be the wiring on the door, possible a break in the wire, therefore the window and the central locking isnt working, possibly the earth wire is broken, open the front passenger door and u should see a sleeve connecting to the rear door, that is where the wiring to the door is, check ! also i would check the fuses. thanks

Feb 15, 2009 | 2005 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22484 Answers

john h

Level 3 Expert

22486 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...