Question about 2005 Chevrolet Avalanche

1 Answer

My 2005 avalanche will not engage into four wheel low

Four wheel high works and auto four wheel works

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 796 Answers

Try shifting the shift selector into Neutral first then try engaging 4wd low. If that doesn't work try shifting into 1st gear and then try engaging 4wd low. The information is inside your owners manual but if this doesn't work please let me know. Also is the light on for which mode your truck is in (2wd or 4wd high)? If not, you may want to check for a blown fuse.

Posted on Sep 19, 2018

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Jerry Cassel

  • 78 Answers

SOURCE: four wheel won't engage

Theres a vacume dash pot under the battery box. It pulls a cable that engages the front diff. Put the vacume line and you'll have lights and four wheel drive. (it happened to my blazzer)

Posted on Dec 29, 2008

Bruce Cooke

  • 1 Answer

SOURCE: Help... My four wheel drive

Try at full stop in neutral switching to 4 wheel auto ,give it a few seconds and if you don,t here it engage try putting it into reverse and then back into neutral and then into drive. If still dosen,t work tranny switch is likely sticking . service or repair.

Posted on Jan 02, 2009

emissionwiz

Marvin

  • 85222 Answers

SOURCE: PUSH BUTTON FOUR WHEEL DRIVE FORD RANGER NOT WORKING

the transfer case is sticking from non use, change the lube in the case ( Ford ATF) and drive it for awhile it should be ok then.

Posted on Apr 07, 2009

SOURCE: While driving, four wheel drive quit working. It

Check the fuse for the four wheel drive before taking another step,it is electrically engage,hope that help you and clear your mind

Posted on Jan 17, 2010

azhari daud

  • 123 Answers

SOURCE: What would cause my 4x4 light to stay on yet not

stuck 4x4 sensor?? just disconnect the wire. you will get the picture mate..

Posted on Nov 23, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 2009 mahindra pik up wont go into low range 4wd


Try replacing the motor on the back of the transfer case that engages high/low, which should fix the issue.

Feb 16, 2016 | Mahindra Cars & Trucks

1 Answer

92 gmc sierra won't engage in manual 4 wheel drive


it sounds like the front differential is not engaging, check the solenoid on front diff.

Feb 09, 2014 | GMC Sierra Cars & Trucks

1 Answer

My 04 Tahoe will engage in 4-high or 4-low, you can hear the clunk and in 4-low it is in low gear but it will not engage the front axial, but in 4-auto it will work fine. All lights indicate everything is...


I had a 4 wheel drive suburban..it had issues with the high-lock and low-lock..I just used the auto setting because all four wheels were getting power anyway..only time you need lock is when you plan to go bogging in really deep mud..on snow/ice all you need is all wheel drive..you actually have better control..as long as it works in all wheel you should be fine..also be checking the front hubs.. are yours full time or do you have lock outs..on the axle hubs..thats my question

Dec 09, 2013 | 2004 Chevrolet Tahoe

1 Answer

I don't have the owners manual, and have never owned a 4x4 in the past, as stupid as this sounds i don't know the proper procedure to engage 4 wheel drill hi


you have a lever or switch that engages 2wheel normal driving 4 wheel high for wet slippery conditions ,then you have four wheel low for real muddy and deep snow conditions
normally change from 2 wheel to four wheel high on the move .important nearly all 4 wheel drive vehicles must be stopped to engage low otherwise do damage to transmission

Sep 13, 2011 | 1999 Dodge Ram 2500 4WD

1 Answer

I have a 1999 GMC Suburban. I have automatic four wheel drive but when I shift into four wheel high it makes clunking sound. I have not tried four wheel low. I wondered why I can still use auto four wheel...


the auto 4 wheel does the same as part time in jeeps, it engages only when the vehicle loses traction. when auto 4 wheel is on the truck isn't fully in 4 wheel drive. my 02 sierra makes the clunk noise too but it does engage. try checking your fluids, i know its way pass the time for me to change mine out.

Feb 09, 2010 | GMC Suburban Cars & Trucks

1 Answer

While driving, four wheel drive quit working. It


Check the fuse for the four wheel drive before taking another step,it is electrically engage,hope that help you and clear your mind

Jan 17, 2010 | 2001 Ford F250 Super Duty Super Cab

2 Answers

Just got H 2 2005 4 buttons 4 the 4 wheel drive


Use 2 wheels, the other 4wd low ,for climbing at slow speeds: 4wd high, for driving on low traction roads,like mud or snow,at medium speeds: 4wd auto full time all wheel drive, for highway speeds on slippery surfaces, like rain or light snow.

Jan 12, 2010 | 2005 Hummer H2

1 Answer

I have a 04 chevy avalanche z71. My four wheel crive system wants to try and change from 2wheel to 4 whheel high or low while driveing. Sometimes at start up the red light under the 2 wheel high button...


Have you received any failure codes (check engine light)? If you have, find out what they are by going to any parts store and they can read your failure codes for free. Let me know after that.

Nov 07, 2017 | 2004 Chevrolet Avalanche

1 Answer

Help... My four wheel drive High or Low will not engage on my 1995 Ford Explorer Eddie Bauer edition. This is engaged "on the fly". The light comes on indicating they are engaged but they it is not.


Try at full stop in neutral switching to 4 wheel auto ,give it a few seconds and if you don,t here it engage try putting it into reverse and then back into neutral and then into drive. If still dosen,t work tranny switch is likely sticking . service or repair.

Dec 19, 2008 | 1995 Ford Explorer

Not finding what you are looking for?
2005 Chevrolet Avalanche Logo

Related Topics:

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85219 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...