Question about Ford Crown Victoria

2 Answers

My crown victoria engine is cranking but it not start

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,692 Answers

Many times this is a switch in the trunk. This switch is mounted in the left side of the trunk and is next to an air suspension switch if you have air ride.

The switch is called an inertia switch and has a reset button on it. Just press and hold the switch and it will reset and connect the power to the fuel pump.

Posted on May 23, 2018

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Ford Master
  • 5,911 Answers

Have you checked for spark at any of the plugs ?

Posted on May 23, 2018

Testimonial: "thanks answering at the time when car not starting i remove one spark plug and put it back in spark plug cable and connect with ground then again i switch on engine cranking but spark plug not sparking then i leave my car for 2 3 hours it get start and engine running"

  • Robert Wood
    Robert Wood May 24, 2018

    Crank sensor may be heat failing causing intermittent n o start no spark situations .

  • fordexpert May 26, 2018

    I agree, just to add that you should not consider it fixed and should replace suspect parts while it is a good time for you and possible to drive car to make repairs.

×

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

  • 261 Answers

SOURCE: 2000 Ford Crown Victoria

when you hold the accelerator does the vehicle stay running? if so the problem is in ithe IAC idle air control motor, take a small screw driver and using the handle tap the iac motor and usualy the motor will kick in and the vehicle will run fine then if the problem is rectified replace the IAC

Posted on Nov 24, 2008

BILL RICHARDSON

  • 508 Answers

SOURCE: 94 CROWN VICTORIA FUEL PUMP

Yes you can replace it. It is in the fuel tank. You will need to drain the tank and remove it to gain access to the fuel pump. A floor jack will help when lowering the fuel tank. If you fo to a dealer to do this you will be looking probably around $700.00 to replace the pump.

Posted on Feb 18, 2009

Anonymous

  • 28 Answers

SOURCE: crown victoria window motor replacement

remove the door panel. be very careful and make sure you get all the screws out. Should be maybe 2 on the bottom half of the door, and 2 on the top half. one is right by the handle, which is the one i forgot the first time i took my door pannel off. carefully pull the panel upward, and outward at the same time. Once the panel is off, disconnect the controls, and remove the light from the panel. Remove the plastic cover very carefully, it will tear, just keeps noise, and air, and the elements out.
There will be 3 screws, they are torx bolts, once you pull those 3 out. They are located middle of the door towards the right side. The motor will drop down a little bit. disconnect the wires for the motor, and wiggle the motor off of the regulator. the crown vics have a decent size hole to get into the door panel, you can also remove the speaker if that would help you do it. other than that, it just lining up the new motor into the car, pushing it into the regulator, and putting the 3 bolts in, make sure they are snug, and not cross threaded. put everything back together, and your set.

Posted on Mar 19, 2009

Anonymous

  • 33 Answers

SOURCE: need wiring diagram for 2008 ford crown victoria

Hello,

You can purchase the wiring diagram for $5.99 from the following site: http://www.wiring-diagram.com/. You can also purchase a wiring diagram book from the following link: http://cgi.ebay.com/ebaymotors/2008-FORD-CROWN-VICTORIA-MARQUIS-WIRING-DIAGRAM-MANUAL_W0QQitemZ120394723100QQcmdZViewItemQQimsxZ20090320?IMSfp=TL090320147007r15080.

Hope this helps,

Chris

Posted on Mar 23, 2009

Dr Honeydew

  • 93 Answers

SOURCE: 2000 crown victoria serpentine belt installation

Accessory Drive Component Locationsa0011762.gif

Posted on Jun 09, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I hate got water in my engine on my 2000 Crown


stop trying to start up your car, it will create more damage to your engine. water may have seeped into the combustion area or may have rusted your internal engine (crank shaft) due to prolonged exposure to water.If the water damage occurred recently , bring in your car to the nearest service center, have engine checked for damage and an immediate engine oil change, this will resolve the problem.

Oct 20, 2014 | 2000 Ford Crown Victoria

1 Answer

2003 ford crown victoria turns over but wont crank


To clarify - the engine cranks but won't start, or the engine does not crank ?
What have you checked so far ?

Mar 01, 2013 | 2000 Ford Crown Victoria

1 Answer

My 1996 crown victoria want start


possibly the fact it was an obd1 engine and the 96 is obd2

Dec 25, 2012 | 1996 Ford Crown Victoria

1 Answer

Where is the crank positioning sensor 1995 crown victoria 4.6L


Passenger side front of engine to the right of the AC compressor

Nov 24, 2012 | 1994 Ford Crown Victoria

1 Answer

It have a 1994 crown victoria it ran out of gas I put 5 gallons of gas in it, when I turned the motor over it started right up, it ran for about a minute and a half then quit. I changed the filter, checked...


Air in the fuel line. Take one small wire off the starter relay and turn and hold the key in the start position for a while. Listen for the fuel pump. It will run fast for a second then slow down. When it does, put the wire back on the starter relay and crank the engine.

Aug 29, 2017 | 1994 Ford Crown Victoria

1 Answer

Engine does not start immediately when cranking


The problem could be many things. Is the engine light on? Check for proper fuel pressure. Remove one spark plug and inspect. Your vehicle may just need a simple tune up. Spark plugs,distributor cap and rotor,fuel filter.

Jul 26, 2009 | 1991 Ford LTD Crown Victoria

3 Answers

1992 Crown Vic wont crank


Check the starter solenoid. Usually mounted on a fender well. Find by following the + battery cable.

Feb 14, 2009 | 1992 Ford Crown Victoria

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...