Question about Jeep Grand Cherokee

Open Question

How do i replace the evap purge valve on my 98 Jeep Grand Cherokee Tsi?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
savdragon

Brett Spencer

  • 37 Answers

SOURCE: Mustang GT 4.6 EVAP Canister Purge Valve Location?

You will need to remove the right front wheel & wheel well liner. The canister purge valve is behind the cover. It should have two tube going into the bottom and one on the side near the top.
You can fix it!
If this helps you out please rate me!
Brett

Posted on Mar 19, 2009

Ad
Molson02536

Harvey N Tawatao

  • 3854 Answers

SOURCE: IAC Valve Location - 1996 Jeep Grand Cherokee

The idle air control valve is located on the back of the throttle body. It has an oval electrical connector and two torx screws holding it in. Unplug the connector, remove the two screws then lightly tap the body with a soft faced mallet to loosen it from the body. 
Once you have it out and prior to installing a new valve clean the seat inside the throttle body where the idle control fits. This must be very clean! Installation is in the reverse order. 
 To save some cash, pull the valve out and clean it with throttle body cleaner, this usually fixes the problem for quite a while.
Good luck and hope this helps.

Posted on May 28, 2009

Efstathios Govas

  • 285 Answers

SOURCE: crankshaft sensor located 98 jeep grnd cher 4wd 6cy

it is located at the back of the engine on top of the transmission bell housing,the plug runs over to the passenger side of the engine bay and it comes out from behind the engine,you can actually get your hand on the sensor itself from under the hood on the drivers side,and i believe its a 13mm bolt holding it in,the new sensor will have a sticker on the end of it...leave it there,it is used for correct spacing between the sensor and the flywheel,hope this helps

Posted on Sep 23, 2009

Testimonial: "Everything was just like you said but as a not atleast for my jeep it is an 11mm not 13mm. Works great so far (keep fingers crossed) "

calilourw1

Richard Welch

  • 12 Answers

SOURCE: 2003 Jeep Grand Cherokee Laredo - Code P0456 EVAP leak

open hood and ck for broken vacuum hoses going to the purge valve(2 vacuum ports and a wiring connector)
on the drivers side between airbox and firewall
if good remove driver side rear tire and inspect hoses next to the gas tank and 3rd, the canister is in that wheel well also insp for cracked hoses there also, been working for jeep 12 years i charged people about 1 hour to correct this probem.

Posted on Dec 18, 2009

Testimonial: "Thanks!"

michigan man

edgar walker

  • 3533 Answers

SOURCE: blower motor only works on high on 98 jeep grand

you need a temp limited switch and for the most part its close to the blower motor has a small screw on each side with a plug in the middle give these websites a try www.autozone.com and www.alldatadiy.com if all fails stop by your Jeep dealership in the parts department and they be able to show you what i am talking about and print you off pictures and diagrams showing you where it is located wish you the best of luck Michigan Man.

Posted on Jan 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 1999 Jeep Grand Cherokee limited,V8 Quadra-trac which dies on the road; dash gauges drop; "no key" lite displays on dash. Restarts after cools. Two codes P 0443 and 0308 are showing? help


code p 0443 refers to evaporative emission (EVAP) canister purge valve ---circuit malfunction====causes ---wiring--- EVAP canister purge valve ---ECM
code p0308 refers to cylinder 8 ---misfire detected ====causes ---engine mechanical fault ---wiring----ignition/ fuel system--- injector---ECT/MAF sensor---ECM
I am thinking here that it restarts , not after cooling , but after the vacuum in the fuel tank has lessened and allowed fuel to be pumped to the injectors and the fuel pressure is re-established
if that is the case then a weak injector or partially blocked injector will misfire under those conditions
I would fix the purge valve so that the tank vents properly and the rest may go away

Feb 18, 2017 | 1999 Jeep Grand Cherokee Limited

2 Answers

Error codes p0442 and po445


Po442 is evap system leak
check intake and all vacuum hoses for leaks
check evap canister and purge valve
Po445 is evap canister purge valve short circuit
check wiring and connection

Apr 16, 2016 | 2002 Jeep Grand Cherokee Limited

1 Answer

Where is the purge control valve location


The EVAP purge solenoid is located under the hood on the left fender (as seen from drivers position).It has two small lines going to it, one from the engine inlet and the other is going to the EVAP canister.

Jun 14, 2014 | 2002 Jeep Grand Cherokee

1 Answer

Where is the location of purge valve on 2006 buick lacross


Canister Purge Solenoid Valve is part of the EVAP system. The component is mounted to the intake manifold. This is on the 3.6 liter engine.
1e4cad15-bd7b-42f1-982a-7d274cb22c56.jpg

May 01, 2014 | 2002 Jeep Grand Cherokee

1 Answer

Purge valve location on 97 lexus es300


a jeep, lexus? huh?
Purge ?
so why are you asking if you dont even know what it is or does.???
we need to know that , there are 3000 parts on the car and 100 systems. up to.
EVAP?
EGR?
tranny>
where?
why not buy and FSM and look or use Alldata.com , all the time.

Feb 26, 2014 | 2002 Jeep Grand Cherokee

1 Answer

2004 jeep grand cherokee code 442/455


OBD code P0442 Small EVAP leak detected you may need to check the EVAP canister under the vehicle and the purge valve as well check for cracks on the canister or the purge valve and check all the rubber hoses connected to them foe cracks or holes. If you find any damage parts replace them. P0455 which means a large EVAP leak is sometimes referred as the gas cap leak check your gas cap and secure it tight if you still have the code change the gas cap hope this helps after you find and fix the problems get the vehicle to a shop and they will use an OBD scan tool to clear the codes.

Feb 26, 2014 | Cars & Trucks

1 Answer

How to fix obd 2 PO456 on jeep grand cherokee laredo 2002


Usually this P0456 code is caused by an incorrect or faulty gas cap. Filling the fuel tank with the engine running could conceivable cause this code as well or if the cap wasn't properly tightened. Any of the following could also be the cause:
  • A small leak in any of the EVAP hoses or fuel tank hoses
  • A small leak in the purge valve or vent valve
  • The EVAP Canister may be leaking

Oct 09, 2012 | 2003 Jeep Grand Cherokee

1 Answer

2003 Jeep Grand Cherokee Laredo - Code P0456 EVAP leak


open hood and ck for broken vacuum hoses going to the purge valve(2 vacuum ports and a wiring connector)
on the drivers side between airbox and firewall
if good remove driver side rear tire and inspect hoses next to the gas tank and 3rd, the canister is in that wheel well also insp for cracked hoses there also, been working for jeep 12 years i charged people about 1 hour to correct this probem.

Dec 18, 2009 | 2003 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85222 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...