FORD ABS CODE CMDTCs ???stability control inhibit warning

When the Stabilitrak and Traction Control indicators come on and stay illuminated in your 2008 Saturn Outlook, it typically indicates a problem with the vehicle's stability control system. This system helps maintain control and stability during adverse driving conditions, such as wet or slippery roads. There are several potential causes for these warning lights, and it's essential to address the issue promptly to ensure your vehicle's safety and performance. Here are some common reasons for the warning lights to stay on:

1. Wheel Speed Sensor Issues: The Stabilitrak and Traction Control systems rely on information from wheel speed sensors to determine if a wheel is slipping or losing traction. If one of these sensors is malfunctioning or dirty, it can trigger the warning lights.
2. Faulty ABS Module: The Anti-lock Braking System (ABS) module is closely related to the stability control system. If there is a problem with the ABS module, it can affect the functionality of Stabilitrak and Traction Control.
3. Damaged Wiring: Damage to the wiring that connects the wheel speed sensors to the control module can disrupt the communication and trigger the warning lights.
4. Malfunctioning Control Module: The control module responsible for the stability control system can develop faults or errors over time.
5. Brake System Issues: Problems with the vehicle's braking system, including worn brake pads, can sometimes lead to issues with the Stabilitrak system.
6. Faulty Steering Angle Sensor: The steering angle sensor is part of the stability control system. A malfunction in this sensor can lead to warning lights.
7. Low Fluid Levels: Low brake fluid levels can trigger the warning lights, as the stability control system may interpret it as a potential issue with the braking system.

To diagnose and address the problem, you should take your Saturn Outlook to a qualified mechanic or a dealership. They can perform a diagnostic scan using specialized equipment to pinpoint the exact issue that is causing the warning lights to stay on. Once the problem is identified, they can recommend the necessary repairs or replacements.
It's important not to ignore these warning lights, as the stability control system is designed to enhance vehicle safety and performance, particularly in adverse driving conditions. Addressing the issue promptly will help ensure the continued safe operation of your vehicle.

check fuses abs system and have vehicle scanned for trouble code

Just like with every other type of warning light, if it's on, there's a trouble code stored. Get the codes read and post the code. Then we can help.

P0308 - # 8 cylinder misfire . Coil or burnt driver inside the PCM . Your vehicle has coil on plug ignition system ,that means your vehicle has 8 coil's .

C1963 Stability Control Inhibit Warning

You have a problem with the abs an there is a code stored in the EBCM - electronic brake control module . It could be any number of thing's from a wheel speed sensor to a wiring problem or the control module or the modulation pump . As long as the light is on the ABS is deactivated . I would take it a qualified ASE certified repair shop that knows ABS systems

With this many low voltage problems all coming up I would look into a device called the body computer.

DSC means "Dynamic stability control" it is caused by some kind of failure in the ABS/Stability control system, it all one system. You will need to seek a dealer or well equipped outside repair shop with proper tools and training to find out the exact cause of the warning light being on, they will use a special tool to scan the system for the fault code that is stored in the computer control module whenever this warning light is turned on.

That means that the EBTCM has detected a problem within the system.The message indicates that a malfunction exists in the stability enhancement feature.

EBTCM (Electronic Brake and Traction Control Module) is an electronic control module that controls and operates the Anti-Lock brake system, Traction Control System and Stability system. If this module detects a problem, it "asks" the cluster to inform you by displaying a warning message.

You should have your car scanned for trouble codes with a scan tool, the Tech2 scan tool is preferred because other scan tools may not communicate with the EBTCM modules.

Hope helps (remember to rate this answer).

It is a problem with your abs this will cause traction and stability to turn off as they work off abs system. need to have scanned for codes. ebcm is common about going out on these

Anti-Lock Control —Vehicles Built After 03/2002 The 3-channel anti-lock brake system consists of the following components:

• front wheel speed sensors
• front wheel speed sensor rings
• hydraulic control unit (HCU)
• Anti-lock brake control module (ECU)
• rear wheel speed sensor
• rear wheel speed sensor rings
• yellow anti-lock brake warning indicator

The 4-channel anti-lock brake system with traction control and stability assist system consists of the following components:

• active brake booster with integral solenoid
• brake booster release switch
• front wheel speed sensors
• front wheel speed sensor rings
• hydraulic control unit (HCU)
• stability assist module (ECU)
• stability assist event indicator
• lateral accelerometer
• longitudinal accelerometer (4x4)
• rear wheel speed sensors
• rear wheel speed sensor rings
• steering wheel position sensor
• yaw rate sensor
• yellow anti-lock brake warning indicator
• brake pressure transducer
• traction control switch

---------------------------------------------------------------------
I suspect the abs issue is causing the speed control not to work if it happened at the same time the cruise control stopped working. When the yellow ABS light comes on, it means the ABS is dactivated. You may have a faulty accelerometer which senses acceleration and yaw (side to side lean). I have not seen a bad one but you said it is sensitive to acceleration.
I would unplug it and see what happens. The connector should have a small tab to depress so you can pull the connector out.
Here is where it is:

Accelerometer Removal and Installation

1. NOTE: The accelerometer is located under the center, rear passenger seat carpet. (I think you have to remove seat for access).
   Cut the carpeting along the perforations.

1. Disconnect the electrical connector.

1. Remove the nuts and remove the accelerometer.

Have dealer hook up tester and pull fault codes if you can't find an easy solution.
Some background info

A malfunction in the anti-lock brake system will cause the anti-lock brake control module to shut off or inhibit the system. However, normal power-assisted braking remains.

Malfunctions are indicated by the yellow ABS warning indicator in the instrument cluster.

The anti-lock brake system is self-monitoring. When the ignition switch is turned to the RUN position, the anti-lock brake control module will carry out a preliminary self-check on the anti-lock electrical system indicated by a three-second illumination of the yellow ABS warning indicator in the instrument cluster.

During vehicle operation, including normal and anti-lock braking, the anti-lock brake control module monitors all electrical anti-lock functions and some hydraulic operations.

Each time the vehicle is driven, as soon as vehicle speed reaches approximately 20 km/h (12mph), the anti-lock brake control module turns on the pump motor for approximately one-half second. At this time, a mechanical noise may be heard. This is a normal function of the self-check by the anti-lock brake control module.

Pedal pulsation coupled with noise while braking on loose gravel, bumps, wet or snowy roads is normal and indicates correct functioning of the anti-lock brake system.

Warning Lamp Indicator
The anti-lock brake system (ABS) uses the yellow ABS warning indicator to alert the driver of a malfunctions in the ABS.
The yellow ABS warning indicator will come on to warn the driver that the ABS has been turned off due to a symptom that exists in the ABS. Normal power assist braking remains but wheels can lock during a panic stop while the yellow ABS warning indicator is illuminated.

-----------------------------------------
Please report back, I am curious if that is what it is. Good luck