Question about 1998 Ford Explorer

Open Question

Where is the torque converter solenoid on my 1998 Ford Explorer 4.0 sohc located

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 1 Answer

SOURCE: jeep codes location of unit

Got me a complete manual for 199 jeep factory model and found location of each individual unit in question. Manual gives u possible solution to each code and repair and or replace. As a mechanic myself testing, trouble shooting and repair was not that difficult. Shift solenoid was very difficult to get to. Located under the head lamp passenger side.

Posted on Nov 19, 2008

Ad

Anonymous

  • 132 Answers

SOURCE: Locationof the Torque Converter Clutch Solenoid

Your transmission should still work if the solenoid goes bad. It will just shift funny

Posted on Jan 30, 2009

Anonymous

  • 1 Answer

SOURCE: pcv valve :where is it located on a 1999 ford explorer sport 2wd

It is located at the back of the engine near the fire wall. It is gray with a T connector at the top with two hoses coming off of the T and going forward into the intake manifold.

Posted on Mar 07, 2009

Anonymous

  • 172 Answers

SOURCE: 98 ford explorer oil pressure sensor location

2.9L and 4.0L engines-Left side front of the engine, below the cylinder head in the engine block

237d46d.jpg

Posted on Nov 28, 2009

Richard Delahant

  • 1201 Answers

SOURCE: 1998 ford explorer starter solenoid location?

Usually mounted on the inner fender well by the battery, the positive battery cable is hooked to it.

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does a 1996 ford explorer 4.0 eddie baurer have a lock out torque converter


do you mean a Lock-up torque converter ? if so yes ford made electrically lockable torque converters since 94 ( all torque converters are hydraulic activated ,lock-up is proformed using a electric solenoid ) , but only certain transmissions made by ford had them , decode your vin number on left corner of dash to determine if you have E4od transmission or 4a400 model these have solenoid
I ask this because to my knowledge only race cars use a LOck out converter (aka "transbrake") for very high hp startss

Apr 17, 2015 | 1996 Ford Explorer

2 Answers

What is the meaning of code 1744 in 2004 mercury sable


torque converter clutch stuck or not working properly

May 27, 2014 | 2004 Ford Explorer

1 Answer

WHERE IS THE TORQUE CONVERTER CLUTCH SELENIOOD FOUND ON A 98 EXPLORER


Its in the transmission pan..You dont have a po741 do ya?? Usually not the solenoid..You can try it but 95% of the time its the torque converter lock up clutch wore out.Which means torque converter replacement..Need to watch it with a scanner while driving and watch how much RPM slip you have to confirm

Sep 11, 2011 | 1998 Ford Explorer

2 Answers

Where is the fuel filter located at on a 1998 ford explorer?


For 1998 Ford Truck Explorer 4WD 4.0L EFI SOHC 6cyl the Fuel Filter is located under vehicle, driver side, below seating area, near fuel tank, mounted on frame rail in fuel line .

Hope this helps (remember to rate and commene this answer).

Jan 27, 2011 | 1998 Ford Explorer

3 Answers

Engine light is on, flashes when driving above 100 Km


stop by local parts store (Autozone,Advance, etc) and have them do a free fault code test. They can print out a list of faults and clear the codes

Jan 02, 2011 | 1998 Ford Explorer

1 Answer

I am putting a 99 ford explorer tranny in a 98 explorer sport with the 4.0 sohc engine. the bolts match perfect and the torque converter from the 99 tranny lines up perfect with the fly wheel. when I go to...


The torque converter is not all the way in the transmission. Pull the transmission back out(unfortunately) and you will need to shake and wiggle while lightly pushing the torque converter into the transmission. Once it goes over the splines for the pump, you will know and the space between it and the transmission housing will be minimal.

May 13, 2010 | 1998 Ford Explorer

1 Answer

I have a 1998 ford explorer v6 sohc 4.0 l. check engine light came on. Put it on a computer and it says the o2 sensor is slow responding in bank 1 sensor 1. where is this located???


bank one is the passenger side bank of cylinders, the sensor is located in the exhaust pipe of that bank BEFORE the catalytic converter

Jan 25, 2010 | 1997 Ford Explorer AWD

2 Answers

Code PO740 on my 2002 ford explorer what need to be replaced


My 2007 code book says Torque Converter Clutch Solenoid Circuit open.

Go to autozone & have them do free scan & interpret code.

Sep 22, 2009 | 2002 Ford Explorer

1 Answer

Emissions test code comes up as 0743 torque converter circuit problem. how do you fix this on a 1998 ford windstar 3.8l engine?


U have a problem in the transmission torque converter clutch control circuit, most likely the solenoid switch that applies the lock up clutch of the torque converter is defective or a the torque converter itself is defective, the trans pan will need to be removed to check the problem further.

Mar 09, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
1998 Ford Explorer Logo

Related Topics:

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...