2004 Jaguar X-Type Logo

Related Topics:

Susan Kelly Posted on Mar 14, 2017

2004 jaguar x type security failed engine monitor or management failure. car wont crank.

5 Related Answers

Anonymous

  • 5 Answers
  • Posted on Sep 28, 2008

SOURCE: 02 jag x-type wont start

Did you figure out what it was? It may be your key. Take it to a locksmith, or perhaps get it replaced.

Ad

Anonymous

  • 324 Answers
  • Posted on Nov 26, 2008

SOURCE: fuel pump relay 2002 Jaguar x-type 2.5

in the mass fuse box, under the dash, unless you have the manual you will not beable to tell wich one it is.. get a chiltons repair manual or a haynes...

Anonymous

  • 1 Answer
  • Posted on Mar 20, 2010

SOURCE: engine management light stays on

had same problem,and a no cruise message.ten minutes later no cruise message disappeared and cruise worked ok.When i got home was told to turn ignition on and off 5 or 6 times fast and you should hear a bell warning sound and management light was off.only had it reset the previous week due to o2 sensors so was a bit peeved,but the ignition trick did the job.

paul

  • 263 Answers
  • Posted on May 01, 2010

SOURCE: My clock in my Jaguar, 2004, S-Type has the wrong time?

FULLY PRESS THE BUTTON THAT SAYS MODE AND THE CLOCK WILL FLASH PUT 24HR AND TYPE IN THE TIME THEN PRESS MODE AND WILL RESET

Anonymous

  • 1 Answer
  • Posted on Dec 30, 2010

SOURCE: had fuel pump changed on 2001 Jaguar S-type...no

Have you had your car fixed yet ????
I have the same problem, the car will turn but will not start, I can hear the fuel pump not working and haved checked all the fuses, still dont know what else to check.

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My 2004 jaguar s type 3.0L won't crank and start, how do I fix it?

call tow truck AAA auto club,
say jump start my engine.!
PRNDL try both P and N , cranks first and check all fuses.
0helpful
1answer

What makes a 2002 jaguar x type 3.0 to read engine system fault fail and gearbox fault

you need to get the fault codes out of the engine control module and the transmission control module ie ecm and tcm with a eobd fault code reader to help sort this one . common probs are faulty jatco auto gearbox (rubbissh gearbox) poss engine managment sensor failures or even a broken/corroded wire or connector, good luck,.
0helpful
1answer

2004 x type car will not , will not crank, message states that security failed

Use the master key and put in driver door hold it for 15 seconds on unlock it should disab

If you need further help, I’m available over the phone at https://www.6ya.com/expert/richard_b59056c0c62ecb00

0helpful
1answer

2000 Jaguar xj8 turn over won't start stability control fail light on.

the stab light comes on if the battery is low because you are cranking the engine your aj26 v8 engine may have a common problem for cars up to that model/year with worn nicosil coated bores ie. low compression check the vin no. at your jag dealer you can get it started by removing the spark plugs and putting a egg cup of engine oil in to each of the cylinders the first thing to do is to check for fault codes using a obd code reader for a clue followed by a compression test
1helpful
1answer

Wats the code p1000 on my 2002 jaguar x type

P1000 JAGUAR - On Board Diagnostic System Readiness Test Not Complete, this is known as the OBD2 drive cycle.


Possible causes - The vehicle is new from the factory.
- Battery or Powertrain Control Module (PCM) had recently been disconnected.
- An OBD monitor failure occurred before completion of an OBD drive cycle.
- PCM Detected Trouble Codes (DTC) have recently been cleared with a scan tool.
When is the code detected? If DTC P1000 is triggered after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles have not been cleared. P1000 JAGUAR Description The On Board Diagnostic (OBD) monitors are performed during the OBD Drive Cycle. P1000 is stored in continuous memory if any of the OBD monitors do not carry out their full diagnostic check.
0helpful
1answer

How does the connecting rods break on a jaguar

They will break under high tension due to timing belt failure or over reving (racing) the engine for too long (the pistons scavange the oil faster than the cylinders can provide, thus the heat friction seizing the piston to the cylinder wall and the rod breaking with the force of the crank still going.)
5helpful
1answer

2003 jaguar s type what does p 1000 code mean

If the Dianosis test Code P1000 is flagged after DTCs have been cleared, all engine management OBD diagnostic monitor drive cycles HAVE NOT BEEN COMPLETED. See http://www.bluejag.co.uk for further details on this
0helpful
1answer

2003 jaguar s type what does p 1000 code mean

It shows that your fault management system has been recently reset. It will not bring on the engine management light. For more info on fault codes goto
http://www.bluejag.co.uk/
Not finding what you are looking for?

272 views

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6988 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...