How do i replace a chevy aveo windshield washer reservoir

Very easy. Undo the electrical connector, remove the tube, remove the bolts. Videos in the link

https://www.google.com/search?q=2018+Chevy+Malibu.+replace+windshield+washer+reservoir

..

Hi roberto ismael luna, I want to help you with your question, but I need more information from you. Can you please add details in the comment box?
what country,? (the vary by....this)
those parts swaps are they OEM new or used.?
that failure is called auto park.
traditionally that is only function of the
whole wiper assembly (not motor neat) as the assembly casing has switches, to do that.
it is a safety issues. to the wipers do not stick and block your view down the road.
sure the list of possibles.
1: control arm ,mostly no. (wiper)
2: wiper, whole assembly , not just motor.
3; fuses
4: relays
5: bad wiring.
6: controllers, BCM etc?

I say #2 is bad and exactly this part black at blue arrow, CAM box
the motor is not bad ,the switch cam, does AUTO PARK.
use only NEW parts. not pulls or salvage , or Pro grade Refurbs
for CARDONE 1

From the 2013 operators manual;

Push the windshield wiper lever forward to spray washer fluid on the rear window. The lever returns to its starting position when released.

The windshield washer reservoir is used for the windshield and the rear window. Check the fluid level in the reservoir if either washer is not working.

Remove the bolt holding the reservoir to the fender. Lift the reservoir up and disconnect the washer hose and electrical connector. Remove the entire reservoir from the vehicle and drain. Replace pump

Front & rear run from the same reservoir

The hose could be clogged ! Do you know where you add the washer fluid ? Somewhere on the bottom of that plastic bottle is the washer pump .
Removal and Installation
> WARNING: Windshield washer solution contains methanol, which is poisonous. Observe all cautions and warnings indicated on label of washer solution container. Failure to follow these instructions may result in personal injury.
> CAUTION: When replacing the windshield washer pump be careful not to damage the rubber grommet.
> CAUTION: Do not operate the windshield washer pump before filling the reservoir. Failure to do so could result in premature pump failure.

1. NOTE: When installing the reservoir, the filler neck must be lubricated using a water-based lubricant.
   Remove the bolt and the windshield washer reservoir filler neck.

1. Remove the RH fender splash shield. For additional information, refer to Section 501-02 .

1. Remove the foam filler and remove the retainer.

1. Remove the 2 screws and the accessory drive splash shield.
   • To install, tighten to 5 Nm (44 lb-in).

1. Remove the nut, 2 bolts and position the A/C accumulator aside.
   • To install, tighten to 9 Nm (80 lb-in).

1. Unclip the A/C lines from the inner fender well.

1. Drill out the rivet and remove the bracket.

1. Remove the 2 bolts, slide the windshield washer reservoir assembly forward to release it, and position the washer reservoir aside.
   • Install the upper bolt followed by the lower bolt, and tighten to 5 Nm (44 lb-in).

1. Disconnect the windshield washer tube assembly from the pump and release the windshield washer tube assembly from the washer reservoir.

1. Disconnect the electrical connector from the windshield washer pump.

1. Release the wiring harness from the reservoir, and remove the washer reservoir.

1. To install, reverse the removal procedure.

Hi You should replace it with a new switch. Good luck.

the pump motor likely is bad. get a used washer fluid reservoir at a pick n pull yourself or at car-part.com. page with * is lowest cost.

Pump and Reservoir, Windshield Washer Removal

1. Disconnect the battery ground cable (14301).
   
2. Raise and support the vehicle.
   
3. Remove the RH wheel (1007).
   
4. Remove the RH front fender splash shield (16103). Refer to Section 01-02 for the removal procedure.
   
5. Remove the windshield washer reservoir top bolt.
   
   
6. Disconnect the windshield washer reservoir fluid level sensor electrical connector.
   
7. Disconnect the rear window washer pump electrical connector from the rear window washer pump.
   
8. Disconnect the windshield washer pump electrical connector from the windshield washer pump (17664).
   
9. Place a suitable drain pan under the windshield washer reservoir (17618) and drain the washer fluid.
   
10. NOTE: The rear window washer hose end is color-coded, matching the connector on the rear window washer pump. Match the colors to ensure proper installation.
    
    Disconnect the washer hoses from the windshield washer pump and the rear window washer pump on the windshield washer reservoir.
    
    
11. Loosen the two windshield washer reservoir side bolts.
    
12. Remove the windshield washer reservoir by sliding it out of the side slots.
    
13. Remove the windshield washer pump.
    
    Installation

To install, reverse the removal procedure. Tighten the lug nuts (1012) to 98-118 Nm (72-87 lb-ft).

if i am not mistaken it uses the same reservoir as your windshield washers. if its not working it may be plugged or malfunctioning.

Reservoir —Windshield Wiper

Removal

1. Remove the RH wheel; refer to Section 204-04 .

1. Position RH splash shield aside.
   1. Remove six screws.
   1. Remove three pin-type retainers.
   1. Position RH splash shield aside.

1. NOTE: Windshield washer fluid should be collected in a container after the windshield washer hoses are disconnected.
   Disconnect the electrical connector and washer hoses.

1. Remove the upper reservoir bolt.

1. Remove the windshield washer reservoir.
   • Loosen the two lower reservoir bolts.

------------------------------------------------------------------------------------