SOURCE: how do i install a water pump on a 1999 olsdmobile alero 2.4 liter
you need a haynes repair manually.because you have to remove timing chain cover. you have to remove timing chain tensioners.to unload timing chain.because water pump is going to interfere with timing chain housing.you will need a manually . too much to tell you in words.
SOURCE: 1999 Olds Alero 3400 motor -- location of Crankshaft sensor
Welcome to fixya. If you need anything else go to www.collisionrepairadvice.com here is the location.
On the lower rear of the engine (LA1) for the 7x
and for the 24x
On the lower rear of the engine (LA1
Testimonial: "Got it Thank You!!! Actually my problem was a bad fuel pump in the gas tank."
SOURCE: 2003 alero water pump location
Passenger side of the engine closest to the radiator,beside the overflow tank.
SOURCE: how to change water pump on 1999 alero 2.4 liter
REPLACE WATER PUMP ON A 1999 OLDSMOBILE ALERO. FIRST YOU HAVE TO DRAIN COOLANT SYSTEM IN A LARGE DRAIN. RADIATOR DRAIN PLUG SHOULD BE ON THE BOTTOM ON PASSENGER SIDE. THEN RAISE THE VECHICLE SUPPORT VECHICLE WITH JACKSTANDS. REMOVE THE EXHAUST MANIFOLD FROM THE ENGINE. CAUTION DO NOT ROTATE THE FLEX COUPLING ON THE FRONT EXHAUST PIPE MORE THAN 4 DEGREE OR DAMAGE TO THE FLEX COUPLING MAY OCCUR. REMOVE THE THERMOSTAT AND THE COOLANT INLET PIPE FROM THE WATER PUMP HOUSING AND SEPARATE THE ASSEMBLY FROM THE ENGINE. LOWER THE VECHICLE REMOVE THE BRAKE BOOSTER VACUUM HOSE FROM THE CAMSHAFT HOUSING. REMOVE THE FRONT TIMING CHAIN COVER AND THE TIMING CHAIN TENSIONER FROM THE ENGINE. CAUTION THE TIMING CHAIN TENSIONER MUST BE REMOVED TO UNLOAD CHAIN TENSION BEFORE REMOVING THE WATER PUMP FROM THE HOUSING OTHERWISE THE WATER PUMP WILL BECOME JAMMED IN THE TIMING CHAIN HOUSING. REMOVE THE HEATER OUTLET PIPE FROM THE WATER PUMP COVER. REMOVE THE WATER PUMP COVER BOLTS FROM THE ENGINE BLOCK AND THE WATER PUMP. REMOVE WATER PUMP RETAINING NUTS AND SEPARATE THE WATER PUMP FROM THE TIMING CHAIN HOUSING. CLEAN THE SEALING SURFACES OF ALL GASKET MATERIAL ON THE WATER PUMP, WATER PUMP COVER AND THE TIMING CHAIN HOUSING. WIPE THE MATING SURFACES WITH A RAG SATURATED LACQUER THINNER OR ACETONE. YOU CAN BUY THESE CHEMICAL AT LOWES OR WALMART DEPARTMENT WHERE THEY SELL PAINTS. FIRST INSTALL THE WATER PUMP COVER AND GASKET TO THE WATER PUMP ON THE BENCH BUT LEAVE THE BOLTS FINGER TIGHT. APPLY A THIN LAYER OF RTV SEALANT TO BOTH SIDES OF THE NEW GASKET AND INSTALL THE GASKET ON THE WATER PUMP. WAIT FOR RTV SEALANT SET UP DRY FIRST. POSITION WATER PUMP AND WATER PUMP COVER ASSEMBLY INTO TIMING CHAIN HOUSING ENGAGING THE WATER PUMP SPROCKET IN THE TIMING CHAIN, AND INSTALL THE NUTS FINGER TIGHT. USE CAUTION TO ENSURE THAT THE GASKET DOESNT SLIP OUT OF POSITION. LEAVE THE NUTS LOOSE TO ALLOW REPOSITIONING WHEN THE BLOCK BOLTS ARE INSTALLED IN THE NEXT STEP. INSTALL THE WATER PUMP COVER TO ENGINE BLOCK BOLTS AND TIGHTEN THEM BY HAND. LUBRICATE THE O - RING ON THE HEATER OUTLET PIPE WITH COOLANT AND INSTALL IT INTO THE WATER PUMP COVER. HAND TIGHTEN THE BOLTS. NOW THAT THE ENTIRE WATER PUMP HOUSING ASSEMBLY IS INSTALLED AND IS FITTED AGAINST THE ENGINE BLOCK. TIGHTEN BOLTS CRISS CROSS SEQUENCE TO INSURE PROPER SEAL TORQUE WATER PUMP TO TIMING CHAIN HOUSING NUTS TO 19 FT LBS .NOW TORQUE WATER PUMP COVER TO WATER PUMP HOUSING BOLTS TO 124 INCH POUNDS. TORQUE WATER PUMP COVER TO ENGINE BLOCK BOLTS 19 FT LBS. TORQUE 124 INCH POUNDS THE RADIATOR OUTLET PIPE TO WATER PUMP HOUSING. INSTALL THE TIMING CHAIN TENSIONER AND COVER. INSTALL THE EXHAUST MANIFOLD. INSTALL THE EXHAUST PIPE TO THE EXHAUST MANIFOLD. WHEN ALL IS DONE. START POURING COOLANT IN THE RADIATOR OR COOLANT OVER FLOW JUG.CHECK FOR LEAKS. IF IS GOOD KEEP ADDING COOLANT TO RADIATOR OR OVER FLOW RESERVOIR UNTIL COOLANT LEVEL STOP DROPPING. NOW START ENGINE. WATCH THE COOLANT LEVEL WHEN START DROPPING ADD MORE COOLANT IN RADIATOR OR OVERFLOW JUG. WHEN COOLANT STOP DROPPING INSTALL RADIATOR CAP OR OVERFLOW JUG CAP. LET ENGINE IDLE UNTIL THERMOSTAT OPENS WATCH TEMPERATURE GAUGE WHEN TEMPERATURE GAUGE RISING TO OVERHEATING. TURN OFF ENGINE WAIT A WHILE TAKE A LARGE RAG SLOWLY OPEN RADIATOR CAP A LITTLE TO RELEASE PRESSURE. WHEN PRESSURE RELEASE REMOVE RADIATOR CAP ADD MORE COOLANT. START ENGINE LET IDLE WATCH TEMP GAUGE. TEMP GAUGE START RISING AGAIN TURN OFF ENGINE LET IT SET A WHILE ADD MORE COOLANT. TO RADIATOR. WHEN ENGINE TEMPERATURE GAUGE STOP RISING AND THERMOSTAT OPENS YOUR COOLANT SYSTEM AIR IS BLED OUT. JUST LET VECHICLE SET A LITTLE CHECK COOLANT LEVEL MAKE ITS CORRECT BEFORE START DRIVING VECHICLE. IF YOU TAKE VECHICLE FOR TEST SPIN TAKE LARGE RAG AND PLENTY COOLANT WITH YOU.IF ENGINE START OVERHEATING WHILE DRIVING PULL OFF ROAD SAFELY WAIT 20 TO 30 MINUTES. USE LARGE RAG SLOWLY OPEN CAP A LITTLE RELEASE PRESSURE. THEN REMOVE RADIATOR CAP ADD MORE COOLANT IF NEEDED. HOPE THIS HELP.
SOURCE: I need to replace the
you need to drop the fuel tank to access it,one tant is out the top of pump screws on
Remove the negative battery cable. Using a screwdriver, loosen the screw that connects the negative battery cable to the battery post. Pull the cable away from the post.
Lift th car using a jack. Support the Oldsmobile Alero with jack stands and the engine using a lift or some other engine support device.
Drain the Oldsmobile Alero's colling system by opening the cap on top of the radiator and unplugging the drain plug underneath the radiator. Position a large container under the drain hole to catch the draining coolant.
Disconnect the components that lead to the water pump with an adjustable wrench Lay them out in the order removed. In order, these parts include the automatic transaxle (if equipped), front wheel on the right side, splash shield, water pump sprocket and the access plate to the timing cover.
Use the access plate bolts to secure the water pump sprocket holding tool to the engine cover. Remove the pump bolts, front cover, thermostat housing, water pump feed pipe and two engine bolts using the adjustable wrench. Lift off the water pump.
Remove the bolts that secure the water pump to the block. Take off or scrape away the gasket. Remove and discard the o-ring between the water pump inlet pipe and the pump.
Spread a small amount of sealant on the water pump, on the areas where it mounts to the engine. Place the gasket on the sealant. Position the water pump onto the engine.
Insert the new bolts into the water pump. Torque the bolts to 89 inch pounds torque. Reconnect the other components in the order removed using an adjustable wrench.
Re-insert the drain plug into the radiator. Remove the engine support and jack stands. Lower the Olsmobile Alero to the floor.
Refill the radiator with coolant according to the instructions in your owner's manual. Screw on the radiator cap. Attach the negative battery cable to the post. Close the hood and test the car.
179 views
Usually answered in minutes!
×