Question about Chevrolet Astro

Open Question

Location of evap purge valve on 2003 chevy astro van

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 102 Answers

SOURCE: '96 Chevy Monte Carlo- codes P0441 and P1655

it will be the evap solenoid that will be the problem,not sure where it is in that car, sorry

Posted on May 18, 2009

Ad
ghost4548

Paul McGrath

  • 776 Answers

SOURCE: Location of the Purge Control Valve for 2003 Hyundai Tiburon

There were two different engines which were installed in the 2003 Tiberon... the 2.0 liter 4 cylinder:
22c99c7.jpg

And the 2.7 Liter V6:
cb31feb.jpg

Posted on Jun 06, 2009

Anonymous

  • 5 Answers

SOURCE: Where is the egr valve located on a 2003 chevy 4.3

The EGR Valve is located on the front of the Engine under the frest air tube. It is at a 45' angle. When checking look for lodged carbon chunks. I recommend using a gesket with a screen built in. It is located infront of the Thermostat housing.

Posted on Mar 14, 2010

mike lavoie

  • 92 Answers

SOURCE: Where is the idle air control valve located in a

You'll need to remove the interior engine cover(dog house).Torx screws for the covers, 2 bolts on floor. and bolts against the fire wall (i use a long extension with a swivel socket at the end). The IAC valve is screwed in to the side of the throttle housing (where the gas pedal hooks up to the engine).I can get a pic if you need it.

Posted on Dec 30, 2010

terrygallupp

  • 376 Answers

SOURCE: Where is the evap purge canister valve located on

The canister purge valve is located behind the intake manifold in the engine compartment on the firewall side .It should be a small round solenoid with a wire connector attached.It will have a feed hose from the evap cannister to the purge valve and then to the intake manifold.The evap canister is located on under the vehicle on the right side of the gas tank and is held in place by a bracket.If you follow these hoses it will also get you to the canister purge valve.I hope this helped.

Posted on Feb 03, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the evap solenoid located on 99 chevy venture mini van


Which EVAP solenoid , vent or purge ? The purge is under the hood on the engine an the vent is under the vehicle near the EVAP charcoal canister an the fuel tank.

Nov 10, 2017 | 1999 Chevrolet Venture

1 Answer

Where is the purge valve solonoid for a 2000 chevy cavalier?


How do I test a purge solenoid? / Diagnosing an EVAP ...

www.ericthecarguy.com/.../13335-how-do-i-test-a-purge-solenoid-diagn...
My brothers 2000 Chevy Cavalier has a P0440 code. ... the PCM will test the circuit condition of the purge valve solenoid and vent valve solenoid so with the key ...

P0446 2000 chevy S10 4WD Replacing EVAP Vent Valve ...

? 7:54
https://www.youtube.com/watch?v=EVWDc9sM1Co
May 7, 2014 - Uploaded by omar ERA
code .P0446. ... Chevy Truck Hard To Fill Gas Tank - GM EVAP Codes P0442, P0446, P0455 or P0449 ...

EVAP Purge Solenoid Removal - YouTube

? 4:24
https://www.youtube.com/watch?v=Xj605HENFno
Feb 26, 2008 - Uploaded by richpin06a
EVAP Purge Solenoid Removal Saturn S-series. ... Hi, is thispurge can solenoid in the same location for ...

Dec 19, 2015 | 2000 Chevrolet Chevrolet Cavalier Base

1 Answer

Where is purge valve solenoid located?


Mar 16, 2014 - 2 posts - ‎1 author
I have a 2003 Vue 3.0L 2wd.After fueling I have trouble starting, it cranks but I have to pump it a couple of time then it starts, Sometimes after it ... 2008 Saturn Vue Purge valve canister solenoid location ...
9 posts
Aug 24, 2013
access to vent valve solenoid - SaturnFans.com Forums
2 posts
Jan 20, 2013
Service engine soon light: P0440 - SaturnFans.com Forums
6 posts
Apr 15, 2010
Code P0446 (evap solenoid) and now I can't fill the gas ...
16 posts
Nov 17, 2007
More results from www.saturnfans.com

EVAP Solenoid Location - YouTube

? 2:17
https://www.youtube.com/watch?v=jIKaPF2Yw3I
Mar 20, 2007 - Uploaded by richpin06a
Saturn EVAP Solenoid Location. ... How To Test and Replace EVAP Canister Vent Control Valve P0446 - Duration: 6:18. by CarsNToys ...

EVAP Purge Solenoid Removal - YouTube




Dec 11, 2015 | 2003 Saturn VUE

1 Answer

Where is the evap emission control switch on chevy astro van 2002 located?


there is no evap "switch". there are a few components that make up the evap system

1. Purge solenoid
2. Vent solenoid
3. Charcoal canister
4. Tank Pressure sensor
5. Misc. vacuum lines and hoses.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Nov 29, 2015 | Cars & Trucks

1 Answer

Code P0443


Error Code: P 0443
Description:
Evaporative Emission (EVAP) Canister Purge Valve - Circuit Malfunction
Problem Area:
Wiring, or VSV connector loose or detached.
Evaporative emission (EVAP) canister purge valve.

Feb 24, 2014 | 2003 Mitsubishi Montero

3 Answers

Po446 evap vent code where is the evap vent located


Some might have an ses p0446, evap emissions vent circuit low. If you take it to the dealer they want 300-400.00 to fix the problem. GM has a service bulletin on this condition and have the updated part for 180.00, thats suppose to eliminate this issue.

Basically the problem is, the evap purge vent valve gets clogged with dirt, especially if the truck is used in dirty conditions. Well I figured there had to be a cheaper way to cure this problem.

Here it is:
1) find the location of the vent valve; its under the truck, locate the charcoal canister on the front of the gas tank and trace the vent line to the vent valve.
2) Take the bracket loose with a 5/8 wrench.
3) Spin the valve around so the side with the hole is facing you.
4) Take an air compressor and blow the vent valve out.
5) reinstall and clear the code and it's fixed.

Now I know the updated part from gm is supposed to keep the valve from clogging ever again, but why spend the money when all you have to do is blow out the vent valve every 50k-100kmi and save your $$$!

Subject: DTC P0446 (Restricted/Blocked EVAP Vent Path) Set, Service Engine Soon (SES) Lamp Illuminated (Replace Hose/Evaporative Emission (EVAP) Canister Vent Asm) #02-06-04-037A - (02/02/2005)
Models:
- 1999-2003 Chevrolet Silverado Models
- 1999-2003 GMC Sierra Models
--------------------------------------------------------------------------------
This bulletin is being revised to add model years. Please discard Corporate Bulletin Number 02-06-04-037 (Section 06 -- Engine/Propulsion System).
--------------------------------------------------------------------------------
Condition
Some customers whose vehicles are operated in dusty type environments, such as farming or mining off-road type applications, may comment about the illumination of the instrument panel SES light, with a DTC of P0446 (Restricted/Blocked EVAP Vent Path) being set.

Cause
Dirt and dust intrusion into the EVAP canister vent hose assembly, resulting in restricted air flow, may cause this condition.

Part Number 15086429 Hose Asm-Evap Emis Cnstr Vent


Removal & Installation
Purge Solenoid Valve-2.2L (L61) Engine
  1. Disconnect the evaporative emission (EVAP) canister purge valve harness connector.
  2. Disconnect the vacuum pipe from the EVAP canister purge valve.
  3. Disconnect the purge pipe from the EVAP canister purge valve.
  4. Remove the EVAP canister purge valve and bracket.
  5. Remove the EVAP canister purge valve from the purge bracket.
  6. Inspect for carbon release in the EVAP canister purge valve ports.
To install:
  1. Install the EVAP canister purge valve on to the purge bracket.
  2. Install the EVAP canister purge valve and bracket. Tighten the purge bracket nut to 71 inch lbs. (8 Nm).
  3. Connect the purge pipe to the EVAP canister purge valve.
  4. Connect the vacuum pipe to the EVAP canister purge valve.
  5. Connect the EVAP canister purge valve harness connector.
  6. Remove the air cleaner outlet resonator.
  7. Disconnect the EVAP canister purge valve harness connector.
  8. Disconnect the engine purge pipe from the EVAP canister purge valve.
  9. Disconnect the engine vacuum pipe from the EVAP canister purge valve.
  10. Remove the EVAP canister purge valve mounting bracket attaching bolt.
  11. Remove the EVAP canister purge valve along with the mounting bracket.
  12. Installation is the reverse of the removal procedure. Tighten the bracket bolts to 71 inch lbs. (8 Nm).

Purge Solenoid Valve-2.4L Engines
  1. Remove the front purge pipe from the evaporative emission (EVAP) canister purge valve.
  2. Remove the rear purge pipe from the EVAP canister purge valve.
    NOTE The EVAP canister may have released carbon particles, which caused this part to fail, and may cause damage to other components. Check the EVAP canister for loose carbon before returning the vehicle to service.
  3. Disconnect the EVAP canister purge valve electrical connector.
  4. Insert a screwdriver between the EVAP canister purge valve and the mounting bracket in order to release the lock tab.
  5. Remove the EVAP canister purge valve mounting bracket attaching nut, if replacing the bracket.
  6. Remove the bracket.
To install:
  1. Install the mounting bracket and the attaching nut for the EVAP canister purge valve. Tighten the nut to 71 inch lbs. (8 Nm).
  2. Slide the EVAP canister purge valve onto the mounting bracket. Make sure the lock tab locks the valve in place.
  3. Connect the EVAP canister purge valve electrical connector.
  4. Connect the rear purge pipe to the EVAP canister purge valve.
  5. Connect the front purge pipe to the EVAP canister purge valve.

Vent Solenoid Valve-2.2L & 2.4L Engines
  1. Raise the vehicle
  2. Loosen the EVAP canister vent valve hose clamp and slide the clamp down the hose away from the EVAP vent valve hose connection.
  3. Remove the hose from the EVAP canister vent valve.
  4. Remove the EVAP canister vent valve by placing a pry bar between the valve and mounting surface, and moving the valve forward.
  5. Remove the clip from the EVAP canister vent valve harness connector
  6. Disconnect the EVAP canister vent valve harness connector.
To install:
  1. Connect the EVAP canister vent valve harness connector
  2. Install the clip into the EVAP canister vent valve harness connector.
  3. Install the EVAP canister vent valve by pushing the mounts into the original holes.
  4. Lubricate the hose end with lubricant.
  5. Install the hose to the EVAP canister vent valve.
  6. Slide the EVAP canister vent valve hose clamp down on to the hose connection at the EVAP canister vent valve.
  7. Lower the vehicle.

Hope this help (remember commetn and rated this).

Apr 21, 2010 | 2000 GMC Jimmy

2 Answers

2003 chevy cavalier p440 code


This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of alot of parts, including the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicles fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engin

heres some things you can try
Remove and reinstall

the gas cap, clear the code, and drive for a day and see if the codes come back.
Inspect the EVAP system for cuts/holes in tubes/hoses
Inspect for damaged or disconnected hoses around the Evap purge solenoid
Check and/or replace the sensor
Check and/or replace the purge valve
Have a professional use a smoke machine to detect leaks

Apr 06, 2010 | 2003 Chevrolet Cavalier

1 Answer

Were is the evap located on 2001 Chevy s-10 blazer with v6


The EVAP service port is located in the EVAP purge pipe between the EVAP purge solenoid and the EVAP canister. The service port is identified by a green colored cap.

47e8f38.jpg

Fig. Showing location of (1) Evaporative Emissions (EVAP) Canister Purge Solenoid and (2) Exhaust Gas Recirculation (EGR) Valve


4d7b3e9.jpg

Fig. EVAP Purge valve solenoid (3) mounting bolt (2) and insulator (1) on 2000-2005 4.8L, 5.3L, 6.0L Engines

Hope this help (remember rated the post).

Mar 26, 2010 | 2001 Chevrolet Blazer

1 Answer

Where is the egr valve located on a 2003 chevy 4.3 astro van? I think it not funtioning properly


The EGR Valve is located on the front of the Engine under the frest air tube. It is at a 45' angle. When checking look for lodged carbon chunks. I recommend using a gesket with a screen built in. It is located infront of the Thermostat housing.

Mar 08, 2010 | 2003 Chevrolet Astro

2 Answers

HAVE A TROUBLESHOOTING MESSAGE PO446 ON A 2003 CHEVROLET SILVERADO 1500. CHECKED GAS CAP AND TIGHTNED NO CHANGE. AM LOOKING FOR LOCATION OF FOLLOWING PARTS PURGE OR VENT SOLENOID VAPOR CANISTER EVAP VENT...


DTC P0446 Evaporative Emission (EVAP) Vent System Performance

The vehicle control module (VCM) monitors the performance of the evaporative emission (EVAP) system by applying a predetermined level of vacuum to the EVAP system and monitors the vacuum decay rate. The VCM sets this diagnostic trouble code (DTC) if the vacuum decay rate is more than a predetermined value. The VCM monitors the amount of vacuum and the amount of pressure in the EVAP system by monitoring the fuel tank pressure sensor. For this DTC, the VCM turns ON both the EVAP purge valve and the EVAP vent valve when the Conditions for Running the DTC are met. This applies an engine vacuum to a closed EVAP system. The VCM turns OFF both the EVAP purge valve and the EVAP vent valve when the system reaches a correct amount of vacuum. The EVAP system should quickly RELEASE the vacuum in the EVAP system with the EVAP purge valve OFF and the EVAP vent valve OFF (open). This test indicates a blocked or restricted EVAP vent path if the EVAP system fails to release the vacuum quickly enough.

3208f98.gif


Dec 02, 2008 | 2000 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

1,298 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...