At Fixya.com, our trusted experts are meticulously vetted and possess extensive experience in their respective fields. Backed by a community of knowledgeable professionals, our platform ensures that the solutions provided are thoroughly researched and validated.
- If you need clarification, ask it in the comment box above.
- Better answers use proper spelling and grammar.
- Provide details, support with references or personal experience.
Tell us some more! Your answer needs to include more details to help people.You can't post answers that contain an email address.Please enter a valid email address.The email address entered is already associated to an account.Login to postPlease use English characters only.
Tip: The max point reward for answering a question is 15.
Not difficult... Remove the front dash cover (check for visible screws and remove them then pull gently but firmly on the cover)...the remainder should be held on by push in clips. The radio itself is fastened by two bolts at the front. Remove them and slide radio out and disconnect harness and antenna leads. On an aftermarket radio, you will usually need an adapter harness which should be available where you bought the radio. Depending on the radio, you may also need an adapter face plate to mount it. Follow the wiring diagram for the harness that came with the radio. If factory, just plug it in and put it back together.
YOU HAVE TO REMOVE THE HAND BRAKE COVER AND THE GEAR SHIFT COVER. JUST PULL UP ON THE PLASTICS. REMOVE CIGARETE LIGHTER. TWO SCREWS AT THE BOTTOM. REMOVE GLOVE BOX AND LOOK TOWARDS THE RADIO. 10 SIZE HEAD SCREW. REMOVE. THEN JUST PULL OUT THE WHOLE FRONT WITH THE RADIO.
First, open storage located below radio, place ur hand right upright above storage cover and pull out on ac cover ("pop out" cover as radio cover is). After ac cover is off, u can pull radio cover out wich extends up toward upper storage and ac vents, u can then see how brace holds radio, You'll need extention for bottom brace.
You need to pull the plastic cover that runs all along your dashboard, a/c heater controls,and radio. You don't have to pull it out completely just enough where you can unscrew the 4 screws that hold the radio in its place. Just take a flat head screw driver and gently pry the plastic cover off around the radio area. You also might need to pull (with your fingers or flat head again) the cover by where the a/c vents are. Pull out as much as you need so you have room to stick a screw driver in. Once you unscrew the screws (bolts) pull the radio out slowly and begin to pull out the wire harnesses and antenna cable from the back of the radio and there you have!! If your going to replace your radio you will need a single din and you have to buy the adapter piece to put it in. A double din radio will not fit. Good luck.
hy!You can pull off the panel what is over the bezel,and there is two screws.Pull off the radio and there is 3 screws.And now you can pulloff the bezel. (bezel-radio holder...
slowly use a flat head screwdriver on the cover there are 4 clips so pull off in other places evenly when it comes off there are harnesses plugged in for defogger , hazard lights, and clock. after taking those off there r 4 screws for radio.and two harnesses to unclip and one plug. be sure to pull fuse out first or run in to prblem like i did . i dont know which fuse it is and lost owner manual
1: remove center console - 2 parts where the shifter is located... all
of em use clips - just give it a nice pull and it'll pop off
2: remove driver side panel attached to radio console( 2 clips only)
3: remove screw found behind center pocket under a/c control
4: pop out a/c unit (4 clips - 2 on top 2 on bottom) just give it a
nice pull... (was scary at first but easy and won't break anything)
5: pull entire front center panel (silver piece that covers radio/ac etc etc)
6: radio is attached via 4 screws - 2 on bottom - 2 on side
7: remove radio
8: make sure u have the AI install kit to install radio w/
9: reattach everything n you're done!
×