Greetings for All I need Peugeot 405 Alternator/Power Steering Drive Belt diagram

Thanks for using FixYa.

Fig. Accessory drive belt routing-2.7L engine
Chrysler Cirrus & Sebring Convertible; Dodge Stratus; Plymouth Breeze

Fig. Accessory drive belt routing-Chrysler 2.7L engine

2.7L Engine
A/C & Alternator Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Loosen tensioner locking bolt and pivot bolt.
4. Rotate tensioner clockwise to allow enough slack to remove belt

To install:

1. Install the air conditioning compressor/alternator belt on pulleys, tensioner in slack position, slip belt over idler last.
2. Adjust drive belt tension.
3. Install the belt splash shield and right front wheel.
4. Lower vehicle.
   
   
   

   Fig. Installing A/C & alternator belt-2.7L engine
   

1. Before servicing the vehicle, refer to the Precautions Section.
2. Raise and safely support the vehicle.
3. Remove the right front wheel and belt splash shield.
4. Loosen the tensioner locking bolt and pivot bolt.
5. Rotate tensioner clockwise to allow enough slack to remove the belt

To install:

1. With the tensioner in a slack position, install the Air Conditioning (A/C) compressor/alternator belt on the pulleys. Slip the belt over the idler last.
2. Adjust the drive belt tension.
3. Install the belt splash shield and right front wheel. Tighten the wheel lug nuts to 100 ft. lbs. (136 Nm).
4. Lower the vehicle.
   

Power Steering Belt

1. Raise and safely support the vehicle.
2. Remove the right front wheel and belt splash shield.
3. Remove the air conditioning compressor/alternator belt.
4. Loosen belt adjusting bolt. It is not necessary to loosen the pivot bolt on the power steering pump. There is a bushing incorporated into the power steering pump/bracket that allows it to pivot.
5. Remove the power steering belt.

To install:

1. Install the power steering belt on pulleys.
2. Adjust drive belt tension.
3. Install the air conditioning compressor/alternator belt.
4. Install the belt splash shield and right front wheel.
5. Lower vehicle.

undo the bolts on the alternator and swing it inwards towards the engine,replace the belt and use the alternator to tension the belt with a long tyre iron,the belt should have 1/2"play in the longest run.(yes it is that simple)

Go to google type in engine peugeot 405 engine diagram and many choices will pop up.

just in front of the altenator, there is a 10mm bolt, tighten that and it will tighten the fan belt .
these belts are quite tight, make sure the one you have is the correct length, sometimes the suppliers will send one that is close to the correct size, and is sometimes a few milimeters smaller.

You dont normally have to loosen anything else, but the easiest way is to put the belt on the alternator, tensioner and power steering first, then ease the belt over the ridge of the crankshaft last, one rib at a time, but evenly all the way around the pulley.


for more step by step instructions with proper diagram please click on this link directly
http://www.howtodothings.com/automotive/a3038-how-to-replace-a-fan-belt.html
---------
this will help.thanks.

If its not the required one then please write your engine code.
http://www.gigasize.com/get.php?d=0zkocl562ff

petrol or diesel ?? think you may mean petrol ??2000cc with monopoint injection??

ensure that your power steering oil is at the right guage

There is a dynamic tensioner roller, which you need to release before you remove the belt. See the manual, may be it can help you.
http://www.gigasize.com/get.php?d=y0xm4md7nwc

I don't know exactly the engine code but may be this 205 documents can help you.
The alternator belt or ancillary belt need to be removed before you can proceed to cambelt.

ancillary drive belt
http://www.gigasize.com/get.php?d=l541vl4pzbd
cambelt
http://www.gigasize.com/get.php?d=b3pyonwxj1b

send me your adress will send u aux belt pic for air con and non air con