Whats the suspect part B1382 air baglight is on

I used http://www.google.com and entered B1382

It appears that is an error for a Hyundai - you may want to search yourself before going to see a mechanic for repair. You can add information to your FIXYA question either with the edit menu if available to you, or in the comment menu box.

http://www.hyundai-forums.com/sm-2001-2006-santa-fe/246817-code-b1382-air-bag-light.html


Code B1382 air bag light on Hyundai Forums Hyundai Forum

The five beeps - five times would indicate a code 55 , but factory service info only goes to code 53 .

• Audible tone - DTCs retrieved

• Air bag SRS system fault

• REFER to DTC Priority Table.

Did your air bag light flash at all ? Apparently this will do flash the air bag light codes as well .
Symptom Chart Condition Possible Sources Action

• Air bag warning indicator is illuminated continuously

• Fuse
• Damaged wiring, terminals or connectors
• A faulty diagnostic connector
• A faulted RCM
• A faulty instrument cluster

• Go To Pinpoint Test A .

• Air bag indicator flashing

• Air bag/pretensioner supplemental restraint system (SRS) fault

• REFER to DTC Priority Table.

• Audible tone - DTCs retrieved

• Air bag SRS system fault

• REFER to DTC Priority Table.

• No communication with the restraints control module (RCM)

• Fuse
• Diagnostic tool
• Data link connector (DLC)
• A faulted RCM
• Circuitry

• Go To Pinpoint Test V .

LFC - light flash codes .
Restraints Control Module (RCM) Diagnostic Trouble Code (DTC) Table
DTC a LFC b Description Action To Take - Continuous The Air Bag Indicator is Illuminated Continuously, RCM Disconnected or Inoperative, Loss of Battery Feed, or Loss of Signal Ground Go To Pinpoint Test A . B1231 13 Crash Data Memory Full Install a new RCM and impact sensors. REFER to Inspection and Repair After a Supplemental Restraint System (SRS) Deployment . B1317 Continuous Battery Voltage High CHECK battery voltage; to be below 16 volts. REFER to Section 414-01 . B1318 Continuous Battery Voltage Low CHECK battery voltage; to be above 9.0 volts. REFER to Section 414-01 . B1342 12 RCM Is Faulted Install a new RCM. B1869 NONE
Continuous lamp
Secondary air bag warning sounds if another fault is present Lamp Air Bag Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test B . B1870 NONE
Secondary air bag warning sounds if another fault is present Air Bag Warning Indicator Circuit Short to Battery Go To Pinpoint Test C . B1891 53 Air Bag Tone Warning Indicator Circuit Short to Battery Go To Pinpoint Test D . B1892 53 Air Bag Tone Warning Indicator Circuit Open or Short to Ground Go To Pinpoint Test E . B1921 14 Air Bag Diagnostic Monitor Ground Circuit Open Go To Pinpoint Test F . B2292 33 Restraint System - Safety Belt Pretensioner Fault (Driver Pretensioner Circuit Fault) Go To Pinpoint Test G . B2292 34 Restraint System - Safety Belt Pretensioner Fault (Passenger Pretensioner Circuit Fault) Go To Pinpoint Test G . B2293 19 Restraint System - Air Bag Fault (Driver Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2293 21 Restraint System - Air Bag Fault (Passenger Front Air Bag Circuit Fault) Go To Pinpoint Test H . B2294 24 Restraint System - Curtain Fault (Driver Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2294 25 Restraint System - Curtain Fault (Passenger Side Air Curtain Circuit Fault) Go To Pinpoint Test I . B2295 22 Restraint System - Side Air Bag Fault (Driver Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2295 23 Restraint System - Side Air Bag Fault (Passenger Seat Side Air Bag Circuit Fault) Go To Pinpoint Test J . B2296 42 Restraint System - Impact Sensor Fault (Front Impact Severity Sensor Circuit Fault) Go To Pinpoint Test K . B2296 43 Restraint System - Impact Sensor Fault (Driver Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 45 Restraint System - Impact Sensor Fault (Driver Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 44 Restraint System - Impact Sensor Fault (Passenger Side Front Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2296 46 Restraint System - Impact Sensor Fault (Passenger Side Second Row Impact Sensor Circuit Fault) Go To Pinpoint Test K . B2434 51 Driver Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test L . B2435 51 Driver Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test M . B2438 52 Passenger Safety Belt Buckle Switch Circuit Short To Ground Go To Pinpoint Test N . B2439 52 Passenger Safety Belt Buckle Switch Circuit Resistance Out Of Range Go To Pinpoint Test O . B2477 Continuous Module Configuration Error INSTALL a new RCM. B2691 51 Driver Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test P . B2692 52 Passenger Safety Belt Buckle Switch Circuit Fault Go To Pinpoint Test Q . C1414 15 Incorrect Module Design Level Go To Pinpoint Test R . C1947 49 Driver Seat Track Position Sensor Circuit Short to Ground Go To Pinpoint Test S . C1948 49 Driver Seat Track Position Sensor Circuit Resistance Out Of Range Go To Pinpoint Test T . C1981 49 Driver Seat Track Position Sensor Circuit Fault Go To Pinpoint Test U . - - No Communication with the Restraints Control Module Go To Pinpoint Test V . Your best bet have codes checked with a scan tool .

If the air bag light is on there is a code stored in the SRS restraint module - air bags ! Wiring problem , impact sensor ! First place to start is have the vehicle check for codes . Not with OBD2 code reader., factory or professional grade scan tool . If you have not worked on air bag systems I recommend you take it to a ASE certified repair shop or the dealer . People have been killed by accidental air bag deployment , by not knowing what's up . Takes special tools !

There is no relay for the passenger side air bag . What seams to be the trouble ? There is possibly a code set in the air bag control module .
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants, in addition to that provided by the 3-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles are also equipped with driver and front passenger safety belt retractor pretensioners. These vehicles can also be equipped with optional side air curtains that deploy from the A-pillar to the C-pillar upon a side impact. Vehicles with optional side air curtains are also equipped with seat side air bag modules in the front seats.
Side air curtains deploy from the headliner, protecting the first and second row outboard occupants during a side impact. Seat side air bag modules deploy from the outboard front seat backrest upon a side impact. In addition, a front impact severity sensor is mounted to the lower radiator support, a seat position sensor is mounted to the driver seat and a usage detection switch is added to the front driver and passenger outboard buckles. If equipped with optional side air curtain modules and seat side air bag modules, there are an additional 4 side impact sensors.
Vehicles are also equipped with an occupant classification sensor (OCS) system as part of the front passenger seat. The OCS system includes 2 OCS rails and an OCS module.
Passenger Air Bag Deactivation (PAD) Indicator
The passenger air bag deactivation (PAD) indicator is a visual indicator used to inform the front seat occupants of the passenger air bag deactivation state. The PAD indicator is a stand-alone lamp installed into the vehicle instrument panel in a position visible to each front seat occupant.
The restraints control module (RCM) controls the state of the PAD indicator through a direct hardwire connection, based on information provided by the occupant classification sensor (OCS) system. The PAD indicator is lit to indicate the passenger air bag module is disabled. An exemption to this is when the front passenger seat is determined to be empty and passenger safety belt buckle unbuckled, and therefore indication of a deactivated passenger air bag module is not necessary. In all other cases, the PAD indicator is unlit when the passenger air bag module is enabled.
When the ignition switch is in the ON position, the PAD indicator prove-out period is initiated by the RCM. The RCM briefly activates the PAD indicator to prove-out the indicator function and verify to the front occupants correct functional operation of the PAD indicator.
The PAD indicator will be lit/unlit within 1.0 to 1.5 seconds of a change of state from the OCS system.
When an OCS system fault is present, the RCM defaults the passenger air bag module to the last valid state received from the OCS system until the ignition switch is turned OFF. If the OCS system fault is still present when the ignition switch is turned ON, the RCM defaults the passenger air bag module to enabled regardless of the size of occupant in the front passenger seat. The PAD indicator will be unlit. For information on the OCS system, refer to Occupant Classification Sensor System in this section.
The following table indicates the passenger air bag status and the PAD indicator status based the size of the front outboard passenger occupant.

1) Front End Sensor - Right--Located under the front hood in the engine compartment (2) I/P Air Bag--Located at the top right under the instrument panel (3) Roof Rail Air Bag - Right--Located under the headliner, extending from the passenger front windshield pillar to the passenger rear windshield pillar (4) Side Impact Sensor (SIS) - RF--Located under the right front door trim near the lower rear of the door frame (5) Sensing and Diagnostic Module (SDM)--Located underneath the vehicle carpet under the center console (6) Seat Belt Pretensioner - RF--Located under the trim near the bottom of the center pillar (7) Side Impact Sensor (SIS) - RR--Located under the right rear door trim near the lower rear of the door frame (8) Roof Rail Module - Right--Located behind the garnish molding on the upper rear pillar (9) Roof Rail Module - Left--Located behind garnish molding on the upper rear pillar (10) Side Impact Sensor (SIS) - LR--Located under the left rear door trim near the lower rear of the door frame (11) Seat Belt Pretensioner - LF--Located under the trim near the bottom of the center pillar (12) Side Impact Sensor (SIS) - LF--Located under the left front door trim near the lower rear of the door frame (13) Roof Rail Air Bag - Left--Located under the headliner, extending from the driver front windshield pillar to the driver rear windshield pillar (14) Steering Wheel Air Bag--Located on the steering wheel (15) Vehicle Battery--Located at the front left of the engine compartment. (16) Front End Sensor - Left--Located under the front hood in the engine compartment

It means that the air bag diagnostic module has registered a problem in the system...either a bad impact sensor, bad air bag module, bad clock spring, bad pre tentioner....something in the system is not as it should be. You need to have the car hooked up to a diagnostic computer that can talk to the air bag processor to find out what the problem is.

The Supplemental Air Bag Restraint System consists of two basic sub-systems:

• Driver side air bag module (043B13) and passenger side air bag module (044A74).
• Electrical system, including RH primary crash front air bag sensor and bracket (14B004) , LH primary crash front air bag sensor and bracket (14B005) , LH kick panel safing rear air bag sensor and bracket (14B007) and air bag diagnostic monitor (14B056) .

---------------------------------------------------------------------------------------
13 Air Bag or Primary Crash Sensor Circuit Shorted to Ground

Inspect air bag sliding contact wiring in steering wheel , driver side air bag module , and passenger side air bag module for damaged, chafed or pinched wires.

-------------------------------------------------------------------------------------

AIR BAG (SUPPLEMENTAL RESTRAINT SYSTEM) General Information The Supplemental Restraint System (SRS) is designed to work in conjunction with the standard three-point safety belts to reduce injury in a head-on collision. WARNING
The SRS can actually cause physical injury or death if the safety belts are not used, or if the manufacturer's warnings are not followed. The manufacturer's warnings can be found in your owner's manual, or, in some cases, on your sun visors. Depending on your vehicle, the SRS may be comprised of some or all of the following components:

• Driver's side air bag module
• Passenger's side air bag module
• Air bag diagnostic monitor computer
• Left and right-hand radiator primary crash air bag sensor and bracket
• Center cowl safing rear air bag sensor and bracket
• Left-hand kick panel safing rear air bag sensor and brackets
• Air bag warning indicator
• Tone generator (internal to the air bag diagnostic monitor)
• Electrical wiring
• Air bag Electronic Crash Sensor (ECS)

The sensors in the car are designed to detect a severe frontal impact. When at least one of the primary crash sensors and the center cowl safing rear air bag sensor close at the same time, electric current flows to the inflator and ignites the chemicals. The chemicals burn rapidly in the metal container. This burning produces nitrogen gas and small amounts of dust, both the gas and dust are cooled and filtered during the air bag(s) inflation. The air bag(s) split the trim covers open while inflating. The air bag(s) then rapidly unfold and inflate in front of the driver or passenger. After the air bag(s) have inflated, the gas escapes through holes in the bag(s) and the they will deflate.

There are no campaigns/recalls for the SRS (Supplemental Restraint System - Air Bag). However, there is a Service Bulleting regarding the wiring harness under the seats:
DESCRIPTION: Motion of the side impact air bag wiring harness and connector may result in illumination of the air bag warning light and one or both diagnostic codes listed below:

• B1378: Driver side air bag (DSAB) resistance high.
• B1382: Passenger side air bag (PSAB) resistance high.

This campaign provides a new side impact air bag wiring harness connector mounting procedure. VEHICLES AFFECTED:

• Model : 1999 - 2002 SONATA vehicles
• Production date range: - Produced through July 23, 2001
  
• VIN range: - Produced through KMHWF35H82A526636
  

SPECIAL NOTES: The service procedure to be followed depends on the original wire harness routing under the seats. The required parts are different for each procedure.

• For vehicles produced on or before June 30, 1999, use the procedure for Type 1 seats. Order service kit part number 88010-38A00.
• For vehicles produced on or after July 1, 1999, use the procedure for Type 2 seats. Order service kit part number 88010-38B00.

If your vehicle doesn't fall within the production range, it's not affected.
I recommend you take the vehicle into a Hyundai Service Department and ask them if your vehicle has had this repair already. If it doesn't apply, pay the diagnostic fee to find out what the problem is. They will give you an estimate of repairs (parts, labor, tax, time-frame, etc.).. Then you'll know what the problem is.

first, you need to read the Lamp Fault Code, LFC from the flashing light. Here's how:

Lamp Fault Codes
When the restraints control module (RCM) detects a system fault, it will cause the air bag indicator to flash a coded sequence: a lamp fault code (LFC). The code is two digits. The first digit is flashed with a 0.5 second interval between pulses. There is a 2 second pause before the second digit is flashed, which also has a 0.5 second interval between pulses. There is a 5 second pause between each display of an LFC.
Each LFC is flashed five times after which the air bag indictor will remain lit for the remainder of the key-on cycle. If there are multiple LFCs, each LFC will flash in order of priority.
-------------------------------------------------------
The fault could be in the air bag circuits, the canopy circuits, the pretensioner circuit on the seat belts, etc.
Report back with code.

here's some of system.

SECTION 501-20B: Supplemental Restraint System 2003 Expedition/Navigator Workshop Manual
DESCRIPTION AND OPERATION Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) The air bag supplemental restraint system (SRS) is designed to provide increased collision protection for front seat and second row outboard occupants in addition to that provided by the three-point safety belt system. Safety belt use is necessary to obtain the best occupant protection and to receive the full advantage of the SRS.
This vehicle line contains dual stage deployment (advanced restraint system) driver and front passenger air bag modules. These vehicles can also be equipped with optional safety canopies that deploy from the A-pillar to the C-pillar upon a side impact or if a rollover condition is detected. If equipped with safety canopies, a unique restraints control module (RCM) is used.
See the following illustration for deployable component location.
Air Bag and Safety Belt Pretensioner Supplemental Restraint System (SRS) Deployable Components Item Part Number Description 1 611D10 Passenger air bag module 2 042D94 Passenger side safety canopy module 3 042D95 Driver side safety canopy module 4 61203 Driver safety belt buckle and pretensioner 5 043B13 Driver air bag module 6 14A664 Clockspring 7 61202 Passenger safety belt buckle and pretensioner


Item Part Number Description 1 14B321 Restraints control module (RCM) 2 14B345 Second row, C-pillar side impact sensor 3 14B345 Second row, C-pillar side impact sensor 4 14B416 Driver seat track position sensor 5 14B345 Front row, driver door, side impact sensor 6 14B006 Front impact severity sensor 7 14B345 Front row, passenger door, side impact sensor