Question about 2000 Jeep Grand Cherokee

1 Answer

Where does the power steering return line/hose connect to on the gear box?

Previous owners plugged up valve. I bought the hose but cant find where i am supposed to connect it to on the gear box.

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jeep Master
  • 20,706 Answers

Double posted why>?

Posted on Dec 11, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 chevy Tahoe. hard to turn left. turn right is ok


steering rack or gear . 2X2 - 4X4 engine . Depends on steering system .
When you turn the steering wheel, the steering gear rotates the pitman arm which forces the relay rod to one side. The tie rods connect to the relay rod with the ball studs. The tie rods transfer the steering force to the wheels. Use the tie rods in toe adjustments. The tie rods are adjustable. The pitman arm support the relay rod. The idler arm pivots on a support attached to the frame rail and the ball stud attaches to the relay rod.
The 2 tie rod are threaded into the tube and secured with jam nuts. Right and left hand threads are used in order to permit the adjustment of toe.

Binding linkage , steering gear worn etc....

Power Steering System Description and Operation (w/o Electro-Hydraulic Steering)
The hydraulic power steering pump is a constant displacement vane-type pump that provides hydraulic pressure and flow for the power steering gear. The hydraulic power steering pumps are either belt-driven or direct-drive, cam-driven.
The power steering fluid reservoir holds the power steering fluid and may be integral with the power steering pump or remotely located. The following locations are typical locations for the remote reservoir:
• Mounted to the front of the dash panel
• Mounted to the inner fender
• Mounted to a bracket on the engine
The 2 basic types of power steering gears are listed below:
• A recirculating ball system
• A rack and pinion system
In the recirculating ball system, a worm gear converts steering wheel movement to movement of a sector shaft. A pitman arm attached to the bottom of the sector shaft actually moves one tie rod and an intermediate rod move the other tie rod.
In the rack and pinion system, the rack and the pinion are the 2 components that convert steering wheel rotation to lateral movement. The steering shaft is attached to the pinion in the steering gear. The pinion rotates with the steering wheel. Gear teeth on the pinion mesh with the gear teeth on the rack. The rotating pinion moves the rack from side to side. The lateral action of the rack pushes and pulls the tie rods in order to change the direction of the vehicle's front wheels.
The power steering pressure hose connects the power steering pump union fitting to the power steering gear and allows pressurized power steering fluid to flow from the pump to the gear.
The power steering return hose returns fluid from the power steering gear back to the power steering fluid reservoir. The power steering return line may contain an integral fin-type or line-type power steering fluid cooler.
In a typical power steering system, a pump generates hydraulic pressure, causing fluid to flow, via the pressure hose, to the steering gear valve assembly. The steering gear valve assembly regulates the incoming fluid to the right and left chambers in order to assist in right and left turns.
Turning the steering wheel activates the valve assembly, which applies greater fluid pressure and flow to 1 side of the steering gear piston, and lower pressure and flow to the other side of the piston. The pressure assists the movement of the gear piston. Tie rods transfer this force to the front wheels, which turn the vehicle right or left.


Your best bet , take it to a qualified repair shop.

Sep 19, 2018 | Cars & Trucks

1 Answer

Where do I find a diagram to change the power steering pressure line hose in my 1990 Lincoln Continental?


REMOVAL

  1. Disconnect negative battery cable.
  2. Remove sight shield.
  3. Remove module bracket.
  4. Disconnect No. 6 spark plug wire to prevent damage to wire.
  5. Remove radiator fan shroud assembly.
  6. Remove top RH isolated radiator mount bracket.
  7. Remove remote air cleaner.
  8. Remove ignition coil.
  9. Disconnect electrical connector on power steering pressure switch at steering gear.
  10. Remove pressure switch to allow for tool clearance.
  11. Remove screw at pressure switch and return line bracket.
  12. Remove anti rattle clips from power steering lines.
  13. Remove plastic strap attaching steering gear heat shield to power steering return line.
  14. Remove plastic strap attaching lines to transfer tube on the steering gear.
  15. Disconnect Electronic Vacuum Regulator (EVR) valve wire.
  16. Remove the ground wire from back of engine block.
  17. Remove pressure line fitting at power steering pump using a 5/8 inch flare nut wrench.
  18. Loosen clamp and remove return line at pump.
  19. Loosen clamps and remove return line at power steering oil cooler.
  20. Remove pressure line fitting (gold in color) at steering gear, using an 18mm open end wrench.
  21. Remove return line fitting (silver in color) at steering gear, using an 18mm open end wrench.
  22. Loosen two screws retaining power steering oil cooler to sub frame.
7c30cde.gif

Oct 21, 2010 | 1990 Lincoln Continental

1 Answer

Hello was wondering if you had instructions on how to replace the steering gear box on a 2001 chevrolet s10?


Removal Procedure

Notice: Do not rotate steering shaft after steering column has been removed. Damage to SIR components may occur.

Lock the steering column through the access hole in the steering column lower trim cover using the J 42640.
Remove the air cleaner assembly. Refer to Air Cleaner Outlet Resonator Replacement in Powertrain Management.Remove the intermediate shaft shield from the steering gear.Place a drain pan below the steering gear. Remove the pressure and the return hoses from the power steering gear. Cap or tape the ends of the hoses and the gear fittings in order to prevent dirt from entering the system.Remove the lower intermediate shaft coupling bolt. Draw alignment marks on the lower intermediate shaft coupling and the steering shaft. Remove the lower intermediate shaft coupling from the steering shaft. Remove the pitman arm. Refer to Pitman Arm Replacement.Remove the steering gear mounting bolts and the washers from the frame. Remove the steering gear.
Installation Procedure


Install the steering gear. Notice: Refer to Fastener Notice in Service Precautions. Install the power steering gear to the frame washers and the mounting bolts. Tighten Tighten the power steering gear to frame mounting bolts to 75 Nm (55 ft. lbs.). Install the pitman arm. Refer to Pitman Arm Replacement.Install the lower intermediate shaft to the power steering gear. Ensure that the alignment marks line up. Install the lower intermediate shaft coupling bolt. Tighten Tighten the lower intermediate shaft coupling bolt to 35 Nm (26 ft. lbs.). Install the pressure and the return hoses to the power steering gear. TightenTighten the pressure hose to 25 Nm (18 ft. lbs.) for the vehicle equipped with the 2.2L engines. Tighten the pressure hose to 30 Nm (22 ft. lbs.) for the vehicle equipped with the 4.3L engines. Tighten the return hose to 25 Nm (18 ft. lbs.). Install the intermediate shaft shield to the power steering gear. Install the air cleaner assembly. Refer to Air Cleaner Outlet Resonator Replacement in Powertrain Management. Unlock the steering column by removing the J 42640 from the steering column lower steering column trim cover access hole. Bleed the power steering system. Refer to Bleeding Power Steering System in Steering / Service and Repair.

Jul 23, 2010 | 2001 Chevrolet S-10

1 Answer

How to change the power steering on 96 ford explorer


Section 11-02C: Steering Gear, Power Rack and Pinion, Explorer 1996 Explorer with Power Rack and Pinion Steering Workshop Manual REMOVAL AND INSTALLATION Steering Gear SPECIAL SERVICE TOOL(S) REQUIRED Description Tool Number Pitman Arm Puller T64P-3590-F
Removal
  1. Start engine.
  1. Rotate steering wheel from lock-to-lock (entire gear travel). Record n umber of rotations.
  1. Divide the number of rotations by two. This gives the required number of turns to place system in the on-center position.
  1. NOTE: Verify the front wheels and steering wheel are in the straight-ahead position.

    From the lock position, rotate steering wheel the number of turns determined in Step 3. This places the gear in the on-center position.


    Steering Gear, Explorer




  1. NOTE: Do not rotate steering column when intermediate shaft is disconnected or DAMAGE TO CLOCKSPRING will result.

    Remove bolt retaining the lower steering column shaft to the steering gear input shaft.




  1. Disconnect the lower steering column shaft from the steering gear.
  1. Remove stabilizer bar attachment from frame for clearance to remove gear.
  1. Unscrew the quick connect fittings for the power steering pressure hose (3A719) and power steering return hoses (3A713) at the steering gear housing (3548).


    Power Steering Hose Connections





    Item Part Number Description 1 3A674 Power Steering Pump 2 3A719 Power Steering Pressure Hose 3 3F780 Power Steering Cooler and Hose Assembly 4 3504 Steering Gear 5 5005 Frame
  1. Plug ends of fluid lines removed and ports in gear to prevent damage and entry of dirt.
  1. Remove two (2) nuts from P/S cooler.
  1. Remove P/S cooler from vehicle.
  1. Remove and discard the cotter pin retaining the nut to tie rod end (3A130) and remove nut.
  1. Separate tie rod ends from front wheel spindle (3105) using Pitman Arm Puller T64P-3590-F.




  1. Remove the two nuts, bolts, and washer assemblies retaining steering gear (3504) to front crossmember (5019).
  1. Remove steering gear from vehicle. If required, remove steering gear mounting bracket housing insulators (3F640) and steering gear insulators (3C716) from steering gear housing.





    Item Part Number Description 1 N807881-S60 Bolt 2 385935-S36 Washer 3 3F640 Steering Gear Mounting Housing Insulator 4 3504 Steering Gear 5 N800255-S60 Nut 6 5019 Front Crossmember 7 3C716 Steering Gear Insulator
Installation
  1. If removed, install steering gear mounting insulators into the steering gear housing.
  1. Push the steering gear mounting insulator and steering gear insulator in until there is no space between the lip on the insulator and steering gear housing.
  1. Position steering gear on front crossmember. Install nuts, bolts and washers retaining steering gear to front crossmember. Tighten to 128-172 Nm (94-127 lb-ft).
  1. Position power steering cooler onto bolts and install nuts. Tighten nuts to 68-92 Nm (50-68 lb-ft).
  1. NOTE: The fittings design allows the power steering pressure hose and power steering return hose to swivel when properly tightened. Do not attempt to eliminate looseness by overtightening, since this can cause damage to fittings.

    Connect power steering pressure hose and power steering return hose to appropriate ports on steering gear housing. Tighten fittings to 27-34 Nm (20-25 lb-ft).
  1. NOTE: Make sure the tie rod ends (3A131) are seated in the tapered spindle holes to prevent rotation while tightening nut.

    With the steering gear, steering wheel (3600) and wheel (1007) in the on-center position, attach the tie rod end to front wheel spindle and tighten to 56-76 Nm (77-103 lb-ft).
  1. If necessary, advance tie rod nuts to the next slot. Install cotter pins.
  1. NOTE: Verify that no rotation from the on-center position has occurred.

    Position steering column lower intermediate shaft over steering gear input shaft. Outer input shaft dust shield must be in place. Replace pinch bolt and tighten to 41-56 Nm (30-42 lb-ft).
  1. Replace the front wheel and tire assemblies. Refer to Section 04-04 .
  1. Replace wheel covers.
  1. Lower vehicle.
  1. Refill power steering oil reservoir (3A697) with Premium Power Steering Fluid E6AZ-19582-AA or equivalent meeting Ford specification ESW-M2C33-F.
  1. Purge air from steering system. Refer to Section 11-00 . Verify absence of any unusual power steering noise.
  1. Check and adjust toe alignment specifications. Refer to Section 04-00 .
  1. Make sure steering gear operates correctly and is not leaking.
  1. Check and adjust fluid level in power steering oil reservoir.

Jul 10, 2009 | 1998 Mercury Villager

1 Answer

I bought a used power steering gearbox and pump, but it didn't have hoses. I bought new hoses but not sure what holes on the gearbox i should use. please help


the return line is the one closest to the driver fender and closest to the driver. when box is installed. other one is the high pressure line.

May 25, 2009 | 1983 Jeep CJ7

1 Answer

High pressure power steering hose - one or two?


Here is a pic.

[IMG]http://i253.photobucket.com/albums/hh43/chuck943/DG1690A.gif[/IMG]



1 3A674 Power Steering Pump 2 3A714 Power Steering Pressure Hose 3 3C510 Power Steering Hose Bracket 4 3N824 Power Steering Pressure Switch 5 3504 Steering Gear 6 3A713 Power Steering Return Hose (Gear to Cooler) 7 3D746 Power Steering Fluid Cooler 8 3493 Power Steering Return Hose (Cooler to Pump

Feb 23, 2009 | 1999 Ford Taurus

1 Answer

1988 Volvo 740 wagon missing power steering part


go to am accredited steering specialist shop and they will have/make the right hose for you

May 29, 2017 | 1988 Volvo 740

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...