Where can I get a belt installation diagram?

Hi, I have pasted the procedure for belt replacement below. To replace the tensioner as well, first take the belt off. Then remove the pulley from the tensioner. This will expose the single bolt that holds the tensioner on. Replace the tensioner and then the pulley (if replacing all). Then reinstall the belt.

Alternator/Power Steering Pump Belt
The alternator/power steering pump belt is provided with a dynamic tensioner to maintain proper belt tension.

1. Disconnect the negative battery cable.
2. Raise the front of the vehicle and safely support it with jackstands.
3. Remove the right front splash shield.
4. Release tension by rotating the tensioner clockwise (use a box-end wrench on the tensioner bolt shown in the picture.
5. Remove the belt and install a replacement.
6. Proper belt tension is maintain by the dynamic tension.
7. Install the right front splash shield. Lower the front of the vehicle.
8. Connect the negative battery cable.
   

1. 
   
   
   
   

   Fig. Alternator/power steering pump belt tensioner bolt location
   

You either have the wrong belt, or it's not on correctly. Make sure all of the pulleys are secure. (Like the power steering pump support bracket isn't loose) The diagram for the belt is usually under the hood.

Here is a diagram of the serpentine belt for the Maxima. I don't have instructions on power steering...

http://www.gates.com/common/part_locator/view_diagram.cfm?id=S4003

This help?

Here are some. Hope it helps =D

Timing Marks

Diagram

TORQUE SPECIFICATIONS
Application Ft. Lbs. (N.m)
A/C Compressor Bracket Bolt 37 (50)
Alternator Bracket Adjuster Bolt 16 (22)
Alternator Bracket Bolt 33 (45)
Balance Shaft Pulley Bolt 22 (30)
Camshaft Pulley Bolt
2.2L DOHC 37 (51)
2.2L SOHC & 2.3L 27 (37)
Crankshaft Pulley Bolt 184 (250)
Power Steering Belt Adjuster Nut 11 (15)
Power Steering Pump Bracket Bolt 33 (45)
Power Steering Pump Mounting Bolt 16 (22)
Shift Cable Bracket Bolt 16 (22)
Timing Belt Tension Adjuster 33 (45)
INCH Lbs. (N.m)
Timing Belt Cover Bolt 108 (12)
Valve Cover Nut 90 (10)
Water Pump Bolt 108 (12)

Crankshaft Balancer: Service and Repair
REMOVAL PROCEDURE
1. Disconnect the negative battery cable.
2. Release the accessory drive belt tensioner (3).
3. Remove the drive belt (5) from the engine.
4. Remove the power steering gear from the vehicle.
5. Remove the starter motor.
6. Remove the power steering cooler bolts from the front crossmember.
7. Remove the power steering cooler from the front crossmember and reposition.
8. Release the air conditioning (A/C) belt tensioner (10).
9. Remove the A/C drive belt (1) from the engine.
10. Remove the crankshaft balancer.
INSTALLATION PROCEDURE
1. Install the crankshaft balancer.
2. Install the A/C drive belt (1) to the engine.
3. Install the power steering gear.
4. Install the power steering cooler to the front crossmember.
5. Install the power steering cooler bolts.
^ Tighten the power steering bolts to 11 Nm (97 inch lbs.)
6. Install the starter motor.
7. Lower the vehicle.
8. Install the accessory drive belt (5) to the engine.
9. Connect the negative battery cable.
^ Tighten the negative battery cable bolt to 15 Nm (11 ft. lbs.).
10. Program the Transmitters.

Removal & Installation

1.6L Engine
A/C Compressor Belt

1. Disconnect the negative battery cable.
2. Loosen the A/C compressor mounting bolts.
3. Pivot the A/C compressor towards the engine in order to relieve the tension on the belt.
4. Remove the A/C compressor drive belt from the pulleys.

To install:

1. Properly route and install the A/C compressor drive belt on the A/C compressor, the power steering (if equipped), and the crankshaft pulleys.
2. Adjust the A/C compressor drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
3. Tighten the A/C compressor mounting bolts to 13-20 f t. lbs. (18-28 Nm).
4. Connect the negative battery cable.

Alternator Belt

1. Disconnect the negative battery cable.
2. Remove the power steering pump and the A/C compressor drive belt.
3. Loosen the generator mounting bolts.
4. Pivot the generator towards the engine and remove the accessory drive belt.

To install:

1. Properly route and install the generator drive belt on the pulleys.
2. Adjust the alternator drive belt to obtain 6-8 mm (0.24-0.32 in) deflection for a used belt or 5-6 mm (0.20-0.24 in) deflection for a new belt.
3. Tighten the generator mounting bolts to 17 ft. lbs. (23 Nm).
4. Install the power steering and the A/C compressor drive belt.
5. Connect the negative battery cable.

Power Steering Pump Belt

1. Disconnect the negative battery cable.
2. Loosen the power steering pump mounting bolts.
3. Pivot the power steering pump towards the engine in order to relieve the tension on the belt.
4. Remove the power steering pump drive belt from the pulleys.

To install:

1. Properly route and install the power steering pump drive belt on the power steering pump and the crankshaft pulleys.
2. Adjust the power steering pump drive belt to obtain 6-9 mm (0.24-0.35 in) deflection.
3. Tighten the power steering pump mounting bolts to 22 ft. lbs. (30 Nm).
4. Connect the negative battery cable.

remove the belt to ac compressor.take your serpentine belt go around crank pulley goes around power steering pump goes around alternator and the tensioner on the far left. the water pump on the out side and the top idler pulley out side. the belt drives them from the out side. then you put your ac compressor belt back on.

3 bolts should be holes in the pully too go thru with an extension if their are no holes in the pully then you nee a power steering pump pully remover it can be rented for 5.00 at auto zone

BELT, REPLACE

1. Release belt tension and remove belt from power steering and alternator pulleys. Twist belt to get between tensioner and front cover and between power steering pulley and engine mount bracket.
2. Raise and support vehicle.
3. Turn wheel to the extreme right and remove right side splash shield.
4. Remove belt from crankshaft and A/C compressor pulleys. Twist belt to get between idler pulley and engine mount bracket.
5. Lower vehicle.
6. Twisting new belt to get past the front cover, install belt around power steering pump pulley, Fig. 15. Allow belt to hang free.
7. Twist belt to get between tensioner and front cover, wrap belt around alternator.
8. Remove belt from power steering pulley and set aside.
9. Raise and support vehicle, then twist belt to get between tensioner and front cover, wrap belt around crankshaft and A/C compressor pulleys.
10. Install right side splash shield and lower vehicle.
11. Position belt around power steering pulley and release tensioner.