Question about 2004 Chevrolet Express

Open Question

Where do I find inline fuse for back brakes, 2004 Chevy express van?

Posted by on

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

SOURCE: 1996 chevy express van audio wiring diagram

go to www.the12volt.com

Posted on Aug 31, 2008

Ad
johnjohn2

Johnny Brown

  • 5763 Answers

SOURCE: Where is the fuel filter located on a 2004 chevy

under van in front of fueltank near frame on driverside,hope this helps.

Posted on Oct 27, 2009

rjcnsons

  • 4 Answers

SOURCE: Reverse and interior lights out, chevy express van

Fuse block under the hood. Driver's side, under the brake master cylinder. Number 18. TCB#2. Replace the fuse.

There is an under-engineered ground in the reverse circuit. If you back up with the dome lights on, it could blow that fuse. There should be some extra fuses under the cover of the fuse block.

Posted on Aug 05, 2010

duane_wong

Duane Wong

  • 6826 Answers

SOURCE: How do you change the

Axle Shaft Bearing & Seal Removal & Installation To Remove:

  1. Raise and safely support the vehicle.
  2. Remove the axle shaft.
  3. If replacing only the seal, remove the seal using a suitable seal removal tool.
  4. If replacing the seal and bearing on the 8.6 inch axle, install the slide hammer and adapter behind the bearing and pull out the bearing and seal together.
  5. If replacing the rear axle shaft seal and the bearing on the 9.75 inch axle, install the J 29712 or equivalent bearing puller into the axle housing behind the axle bearing.
  6. Remove the axle shaft seal and the bearing by tightening the nut on the J 29712 bearing puller.
Use a slide hammer, bearing puller and adapter to remove the old axle bearing 88457g81.gif

To Install:
  1. Install the axle shaft bearing using a suitable size driver. Drive the bearing into the housing until the tool bottoms against the tube.
  2. Lubricate the seal lip and install the seal with a suitable seal driver. Make sure the seal is fully seated in the axle tube.
  3. Install the axle shaft.
  4. Fill the rear axle with the correct lubricant.
  5. Lower the vehicle.
prev.gif next.gif

Posted on Oct 18, 2010

newyorkenny

  • 1 Answer

SOURCE: I need a diagram of fuse box for 2000 Chevy Express Van

i have a 2000 Chevy van where is the fuse for the two(2) rear power outlets

Posted on Apr 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the brake light on a 2004 Chevy Express van?


Just go onto google and type in how do I change a brake light on a Chevy express van you will be shown a video of how to do it hope this helps

May 30, 2014 | 2004 Chevrolet Express

1 Answer

2000 chevy express van, no brake lights; left, right and above rear door. Tail lights good and signals all work.


probably a fuse. if the fuses are good check the brake light switch on the brake pedal.

Mar 10, 2014 | 1998 Chevrolet Express

1 Answer

Chevy turn signal


You have a wiring sort, most likely inside steering column or maybe near steering shaft around brake peddle. I hope this helps, Lee.

Feb 09, 2014 | 2002 Chevrolet Express

1 Answer

I have a 2006 chevy express van, I am trying to wire up lights for a trailer. I have brake lights, turn signal lights but no tail lights? All lights and wiring are new.


Check for power at the splice/connector. Also check fuses as it should have different fuses for trailer lighting. Also Try this site http://www.etrailer.com/faq-wiring.aspx. Full of useful info.

Sep 23, 2010 | 2004 Chevrolet Express

2 Answers

Reverse and interior lights out, chevy express van


Fuse block under the hood. Driver's side, under the brake master cylinder. Number 18. TCB#2. Replace the fuse.

There is an under-engineered ground in the reverse circuit. If you back up with the dome lights on, it could blow that fuse. There should be some extra fuses under the cover of the fuse block.

Apr 25, 2010 | 2007 Chevrolet Express Passenger

2 Answers

2004 chevy 3500 express passenger van transmission


if ur replacing it remove front grill disconnect both lines and carefully remove retaining clips from radiator if replacement is original eguipt mount & reconnect --if its a universal follow instructions usually cut off fittings and use clamps and hose to hook up

Oct 27, 2009 | 2004 Chevrolet Express

2 Answers

Disc Brake Emergency brake adjustment on 04' Chev Express Van


Continually push the brake pedal to set the brakes. (With park brake off). Brakes are self adjusting and will adjust to correct position.

Mar 29, 2009 | 2004 Chevrolet Express

1 Answer

I need a diagram of fuse box for 2000 Chevy Express Van


i have a 2000 Chevy van where is the fuse for the two(2) rear power outlets

Oct 30, 2008 | 2000 Chevrolet Express Cargo

Not finding what you are looking for?
2004 Chevrolet Express Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...