Will a 95 ford escort front bumper,fender and hood bolt on to a 97 ford escort

National Auto Body Parts offers a variety of aftermarket bumper covers for your 1988 Ford Escort LX hatchback. You can find the front bumper cover for your car model at a price of $366 .

AutoBodyParts also offers a remanufactured OE front bumper cover for your car model .

Bumper Megastore has a genuine Ford reconditioned front bumper cover for your car model at a price of €329.77 .I haven't try to convert that cost!

CARiD.com offers Autograde™ front bumper cover retainers by Dorman® for your car model at a price range of $2.39 - $10.61

Mary, 1998 to 2004 fender and bumpers will interchange, some bumpers had fog lights. press the helpful button

Remove wheels. Remove fender liners front. Remove three nuts per side from inside fender wells. Remove fog lamp grilles. Remove vertical bolt just inside grilles--pointing up. Remove two screws per side under hood near front of fender. Put milk crate under front bumper. Remove belly pan first. Slide bumper forward onto milk crate, disconnect headlight washer line at quick disconnect if so equipped. Disconnect fog light connectors. Remove bumper.

You have to remove the front bumper cover. Put the car on jack stands (the front) and remove the inner fender plastic. You'll need a long extension and a 10mm socket to remove the nuts and bolts holding the bumper cover in place. Once the cover is off removal of the headlight becomes obvious.

have 96, 95 similar

Section 01-19: Bumpers 1996 Villager Workshop Manual
REMOVAL AND INSTALLATION Bumper and Bumper Cover Front
Removal

1. Raise and support the vehicle.
   

1. Remove the RH and LH front wheel (1007).
   

1. Remove the RH and LH front fender splash shield screws. Remove the RH and LH front fender splash shields (16102).
   
   
   
   
   

1. Remove the four front fender brace screws.
   
   
   
   
   

1. Remove the two front fender brace nuts.
   

1. Remove the two plastic screws.
   

1. Remove the seven clip buttons located under the front bumper cover (17D957).
   
   
   
   
   

1. Remove the RH and LH front turn signal lamps (13369). Refer to Section 17-01 for the removal procedure.
   

1. Remove the four front bumper cover brace bolts.
   
   
   
   
   

1. Remove the front bumper cover from the vehicle.
   
   
   
   
   

1. Remove the two front turn signal lamp wire harnesses from the front bumper (17757).
   
   
   
   
2. Remove the eight front bumper bolts.

1. Remove the front bumper from the vehicle.
   

You have to basically remove the bumper cover in order to do this.
You will need a 10mm socket with a couple extensions and a phillips screwdriver.
First remove the plastic shield inside the wheel well using the phillips screwdriver.
There are 3 10mm bolts that have to be removed the attach the bumper cover to the fender. The first one is just inside the newly uncovered hole. For the other 2 you will need the extensions. They are located all the way back in the hole beside the headlight assembly. If you look in with a flashlight You will see 3 bolts down in there. One of them will have a 1/2 inch spacer on it. Do not worry about this bolt, it holds the header panel on. The other 2 bolts are the ones you need to remove. Once this is done, if you need to remove the bolts under the hood that hold the bumper cover on the header panel. You should now have adequate movement to move the bumper cover out of the way of the 3 10mm bolts on the headlight assembly that were blocked.

there are 4 bolts on the hood 2 each side/ take the top sheild off its retainers then remove front bumper reatianers and bolts on bottom and a bolt oneach side at fenders slide bumper off then you can get to lights and radiator you will have to unbolt the radiator brackets at the top should be able to replace them all

you dont need to disconnect battery, just remove the front grill as there is a bolt hiden behind that, there is a bottom bolt on the lamp and you may need to drop the bumper slightly to get to this, this is easy just remove the 2 crosshead screws by the wheel to drop the bumper slightly.

I have done this for years and am familiar with these cars. The first thing to do is cut in your parts, by that I mean paint the inside edges of your door, fender and hood before you install them. The hood is a no brainer. four bolts probably ten millimeter. The fender is not very hard either, remove headlight and side marker and front bumper. The door needs to be disconnected under the dash and the wires pulled out before removal. Install the door and adjust it till it fits and closes properly, then the fender by lining up the body line before tightning into place. Before putting in the bolts along the top install your hood and align it with the back of the cowl so that it is even gap all the way across then adjust fender gap and tighten down. This will work perfect if your inner structure has not been bent or knocked over. Be glad to help further if you need it