Question about 2000 GMC Jimmy

1 Answer

Remove drivers seat 2000 gmc jimmy

How to remove drivers seat and what kind of tools to use

Posted by Anonymous on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Expert
  • 47 Answers

Four nuts 17 mm hold seat and track to vehicle floor, then unplug wiring harness from bottom of seat and remove from vehicle. Caution- seat may have to be adjusted fully forward to remove rear bolts.

Posted on Jul 16, 2016

Ad

6 Suggested Answers

Anonymous

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
psds4

pat murray

  • 293 Answers

SOURCE: How TO REPLACE A IN TANK FUEL PUMP ON A 2000 gmc jimmy

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800a13e9
hope this helps

Posted on Oct 11, 2008

Anonymous

  • 366 Answers

SOURCE: remove steering wheel on 95 gmc jimmy

u will need a steering wheel puller,u will have to disharm and take airbag off if equip.,i would suggest to get manual it explains step by step procedure!

Posted on Apr 25, 2009

BB1BUD

  • 462 Answers

SOURCE: 2000 GMC Jimmy Power seat stopped working

Left side of the dash, to the right of the IP fuse block. Its a 25 amp circuit breaker, an aluminum cased breaker. CHECK FOR POWER ON THE SEAT SWITCH "A" TERMINAL AND GROUND ON THE "D" TERMINAL. IF YOU HAVE POWER AND GROUND THE SWITCH IS BAD.

Posted on Jun 16, 2009

Testimonial: "thanks"

Larry Cowan

  • 274 Answers

SOURCE: Drivers Side Door Handle

You need to take inside door panel off This just clips on but there are screws in armrest and inside door handle look for any other small square covers that may hide screws Lift panel up Make sure window is up Disconnect wiring from panel and you can now get at door handle linkage and bolts

Posted on Jul 10, 2009

Anonymous

  • 1 Answer

SOURCE: 2000 GMC Jimmy won't start

i had the same problem and replaced the fuel pressure regulator. Cost about $45 at advance auto store or about $90 at napa auto stores. Once i replace that my truck started right yup and runs like a champ

Posted on Jul 13, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Gmc jimmy heated seat not working on one side only.


Hello-
If your fuses are good, perhaps your heated seat switch is faulty. You can test the switch for connectivity using a meter to see if power is going through the switch when in the ON position. If the meter shows no power while in the ON position, replace the switch. If power is reaching the seat, then likely the heating element itself within the seat is the culprit.

Apr 01, 2014 | 2000 GMC Jimmy

1 Answer

2000 gmc jimmy drivers window doesn't work but all others work


With key on door open, hold switch in down position and rap door panel with rubber mallet...if it works, need motor, if not, check switch for power out to motor

Mar 01, 2013 | 2000 GMC Jimmy

1 Answer

2000 Gmc jimmy power lumbar works but seat does not, can't find the exact fuse for seat?


IF THE LUMBAR IS WORKING, THE POWER IS THERE . IF EVERYTHING IS PLUGGED IN UNDER THE SEAT, THE SEAT MOTOR MAY BE FAULTY

Nov 19, 2010 | 2000 GMC Jimmy

1 Answer

How do you remove a heater core from a 2000 GMC JImmy


2000 GMC Jimmy heater core replacement in order to replace a heater core in a 2000 gmc jimmy the coolant must be completely drained and the entire dash including radio, vents and panel covers must be removed. four screws hold the top portion(closest to the windshield) in place. they can be found under the windshield defrost vent. after the entire dash is removed a safety harness under the steering column must be removed and the steering column must be dropped to the driver seat. the heater core housing(black plastic) is located right center of the dash and is a two part housing one piece on top of the other. the housing is attached to the fire wall and must detached before replacement can continue. after detaching the housing from the fire wall separate the housing by unscrewing the six screws that hold it together. the heater core is now exposed. disconnect the heater core from the two hoses and discard. installation is the uninstall process in reverse. it is a very long and drawn out process that is not accomplished in just an hour or two . make sure you have most of the day or several afternoons to finish . Good luck and take pictures with your cell phone to use as reference.

Nov 27, 2009 | 2000 GMC Jimmy

1 Answer

Gmc jimmy keeps eating fly wheels and starters. its like motor is locking for a second.


With starter removed, turn the flywheel with a tool. It is easier with tranny removed, but check for how easily it moves. Does engine have lots of power? Is the engine making any kind of knocking noises?

Sep 27, 2009 | 2000 GMC Jimmy

1 Answer

2000 GMC Jimmy Power seat stopped working


Left side of the dash, to the right of the IP fuse block. Its a 25 amp circuit breaker, an aluminum cased breaker. CHECK FOR POWER ON THE SEAT SWITCH "A" TERMINAL AND GROUND ON THE "D" TERMINAL. IF YOU HAVE POWER AND GROUND THE SWITCH IS BAD.

May 27, 2009 | 2000 GMC Jimmy

1 Answer

How do i change the front hub assembly on a 2000 GMC Jimmy


a cheater pipe to help get leverage and a 18mm socket. remove the caliper and brackets(2 bolts), support the caliper with a block so that it doesn't hang too far. remove the rotor and the hub assembly (3 bolts) clean and grease inside and replace.

Apr 02, 2009 | 2000 GMC Jimmy

1 Answer

2000 GMC Jimmy Power seat stopped working


both my power seats are not working at all ..it first started with driver seat , to make seat move forward and back tilting the recliner was working then it went out ..not working either..then after a month later my pasenger seat stopped working as well... what might be the issue..please reply

Jan 23, 2009 | 2000 GMC Jimmy

1 Answer

Jimmy 2000 sle no power seat


I had the problem with the front seat not working also. It was the connector under the drivers seat that was loose.

Nov 23, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
2000 GMC Jimmy Logo

Related Topics:

96 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85223 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...