Question about 2008 Chevrolet Express

2 Answers

Body control module location 2008 Chevy express 2500

Tested fuse box under driver seat no power there for brake light turn signal right side

Posted by on

Ad

2 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 15,575 Answers

Body Control Module (BCM) is located in the
Lower right side of the instrument panel behind the knee bolster !

Posted on Dec 30, 2014

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 14,585 Answers

It's not the BCM. Since one side works and the other doesn't. The bcm only grounds a relay for the the lights to work. Replace the hazard switch. If it is on the column, replace the turn signal switch. Sending a picture to help. Body control module location 2008 Chevy express 25 - 25345156-hyer52qe2lvlylkatonhnc1i-1-0.gif

Posted on Jan 06, 2015

Ad

6 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Anonymous

  • 5 Answers

SOURCE: Body Control Module - 2000 Chevy Blazer

Not sure about a body control module, there is a pcm under the hood on the pass. side that controls most everything on these, however i would check your fuses for the seat, on the 00 models the headlights do stay on all the time while driving due to daytime running lights but if they stay on after you take the key out then id check the headlight switch or sensor on the pass side dash.

Posted on Sep 02, 2008

Anonymous

  • 1 Answer

SOURCE: Can not find 2000 Chevy Cavalier Flasher Unit

the relay unit is under the dash near the steering wheel should be connected to the searing shaft it looks like a small square green or black the relay is about 35$

Posted on Jun 19, 2009

Anonymous

  • 124 Answers

SOURCE: Park/Tail lights not working. Brake/signals are

Before going ahead and spending money on a new module, test it first. The module is located under the steering column. You'll find a Brown wire on one of the connectors (i just looked at a wire diagram). Do no disconnect anything. Back probe the brown wire, which is the power feed to your park lights. With the lights off, there should be 0 volts on you voltmeter. Turn the park lamps on, There should be 12V. If there is not 12V, disconnect the connector and try to check voltage at the pin that feeds to the brown wire, if still not 12V, replace the module. If you do get 12V, then module is ok, find where the 12v is being dropped before making it to the lamps.

Posted on Aug 09, 2009

RonPark

Ronald Park

  • 855 Answers

SOURCE: 2000 Buick LeSabre where power locks, seats, windows quit working

If all power devices stopped at the same time you may have a bad fuse link. Since it is rare for all the fuses blowing at once and you already checked them. Start at your fuse links before assuming something expensive.

Posted on Aug 11, 2009

Mike

  • 4363 Answers

SOURCE: I have A 2000 Chevy 3500 Express Van and the brake

Hi,

When you said that you checked the brake switch, did you check it live? Meaning verified live power to the switch, press switch, and then power came out the other terminal?

If so, also verify zero power on brake press, at the offending brake light bulb terminal. You must verify the test light each time you move it...leave running lights on...

After verifying that there is no power coming, after the brake is pressed, note the wire color and find it where it comes to the steering column and test there... This would eliminate wires and connections between front and the rear of the vehicle, unlikely, but needs to be tested.

After verifying no power at that terminal, then yes the t/s switch is certainly suspece. This may be the time to get a mechanic to verify and replace the switch, there are locks, tilt mechanisms, air bags, column bearings, etc involved. Failures risk loss of vehicle control (locking or binding for example.)..

Hope this gets you going in the right direction.

Posted on Sep 09, 2009

Testimonial: "Thank You. I tried those things and it seemed to be the Emergency Flasher switch in the multi function switch."

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

07 cadillac cts has no brake light all fuses are good and replace the brake switch.still not working any advice


Stop Lamps
The brake pedal position sensor is a resistive device used to sense the action of the driver's application of the brake pedal. The brake pedal position sensor provides an analog signal that will increase as the brake pedal is pressed.
The brake pedal position sensor receives both a 5-volt reference voltage and a low reference signal from the electronic brake control module (EBCM). When the brake pedal is pressed, a variable signal is applied from the brake pedal position sensor to the EBCM through the brake sensor signal circuit. The fuse block left rear supplies battery positive voltage to the bass relay switch through the BASS fuse. One side of the bass relay coil is permanently grounded at G402. The EBCM supplies voltage to the bass relay coil upon receiving the signal from the brake pedal position sensor. The switch contacts of the bass relay close and battery positive voltage is applied through the bass relay switch to the center high mounted stop lamp (CHMSL), and to the turn signal/hazard flasher module through the stop lamp switch signal circuit. The ground for the CHMSL is applied from G402. The turn signal/hazard flasher module then supplies voltage to the left and right stop lamps in the tail lamp assemblies that have ground at G401 and G402. For export vehicles the stop lamps receive battery positive voltage directly from the bass relay.

Do you know where the rear fuse box is ? Check BAS fuse 15amp. and the bas relay , should be marked on the inside of the fuse box lid . The rear fuse box is located

Fuse Block - Left Rear
In the passenger compartment, under the left side of the rear seat at carpet
Power and Grounding Component Views
Electrical Center Identification Views
Fuse Block - Right Rear
In the passenger compartment, under the right side of the rear seat at carpet.

If fuse and relay are ok your best would be to take to a cadillac dealer .

Jan 19, 2017 | Cadillac Cars & Trucks

2 Answers

Where is the fuse for the power seats located?


PWR ACCY Fuse Breaker A
25A Located in the instrument panel fuse box.
I/P Fuse Box In the left lower kick panel
Power Seat(s), Illuminated Entry Module, Power Door Lock Switches, Remote Control Door Lock Receiver, Power Door Lock Control Module.

Do you have a problem with any of the other components listed ,if no the breaker is good .
Do you have

Jan 31, 2016 | 1999 Chevrolet Express

1 Answer

If it is the blinker switch why do I not have brake light on right rear side as well as no turn signal


The brake light circuit runs through the blinker switch, which is how the turn signal is able to override the brake light.

Jan 13, 2015 | Seat Cars & Trucks

1 Answer

Where is the Body control module location 2008 Chevy express 2500?


It is tucked up under the dash on the passenger side. You will have to remove the passenger knee bolster which is retained with 2 screws along the bottom and a few clips at top.

Dec 29, 2014 | 2008 Chevrolet Express

1 Answer

Body control module location 2008 Chevy express 2500


body control module is on the passenger side of the dash - remove the passenger lower knee bolster and its directly behind it.

Dec 29, 2014 | 2008 Chevrolet Express

2 Answers

I have a 1998 chevy suburban. The dome lights don't work. checked fuse box under hood. All good. Are there other fuses on the truck?


Instrument Panel Fuse Block
The instrument panel fuse block access door is
located on the driver side edge of the instrument panel.

Pull off the cover to access the fuse block.

The vehicle may not use all of the fuses shown.

Fuses Usage
1 Rear Seats
2 Rear Accessory Power Outlet
3 Steering Wheel Controls Back light
4 Driver Door Module
5 Dome Lamps, Driver Side Turn Signal
6 Driver Side Turn Signal, Stop lamp
7 Instrument Panel Back Lighting
8 Passenger Side Turn Signal, Stop lamp
9 Passenger Door Module, Driver Unlock
10 Power Door Lock 2 (Unlock Feature)
11 Power Door Lock 2 (Lock Feature)
12 Stop lamps, Centre High Mounted Stop lamp
13 Rear Climate Controls
14 Power Mirror
15 Body Control Module (BCM)
16 Accessory Power Outlets
17 Interior Lamps
18 Power Door Lock 1 (Unlock Feature)
19 Rear Seat Entertainment
20 Ultrasonic Rear Parking Assist, Power Liftgate
21 Power Door Lock 1 (Lock Feature)
22 Driver Information Centre (DIC)
23 Rear Wiper
24 Cooled Seats
25 Driver Seat Module, Remote Key less Entry System
26 Driver Power Door Lock (Unlock Feature)

Aug 23, 2011 | Chevrolet Suburban 2500 Cars & Trucks

1 Answer

2003 Chevy Silverado SS brake lights aren't working but top cab brake lights are. Bulbs in brake lights are working, and light up when headlights are turned on, but do not get brighter when brake pedal is...


Sounds like the turn signal flasher module has gone bad. It controls the brake lights and turn signals. It is located under the drivers side of the dash. If is a rectangular black box with a grey connector and 8 or so wires connected to it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

Oct 05, 2010 | 2003 Chevrolet Silverado 1500

2 Answers

No turn signals or side brake lights on 94 chevy suburban


the problen is probably the turn signal switch with a test light check for power at brake switch if no power check for power at turn signal switch the brake lights are incorperated through the turn signal switch

Oct 18, 2008 | 1994 Chevrolet Suburban

Not finding what you are looking for?
Cars & Trucks Logo

6,990 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

85216 Answers

Jonah Oneal

Level 3 Expert

14092 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...