Location of input speed sensor on 2008 aveo

Question editerd for clarity.

Question moved to model category, however, there are 3 engine sizes for that model.

VEHICLE 2008 Jeep Commander
All

Parts

Accessories

3.7L Gas; Engine
4.7L Gas; Engine
5.7L Gas; Engine
That part from AUTOZONE!!

2008 Jeep Commander Vehicle/Transmission Speed Sensor AutoZone

https://www.autozone.com/engine-management/vehicle-transmission-speed-sensor/jeep/commander/2008
.

P0717 OBD-II Trouble Code: Input/Turbine Speed Sensor ...

YourMechanic https://www.yourmechanic.com > Articles
P0717 is a diagnostic trouble code (DTC) for "Input/Turbine Speed Sensor No Signal". This can happen for multiple reasons and a mechanic needs to diagnose ...

Missing: Commander ‎' Show results with: Commander

Code P0717 Jeep Input Speed Sensor 1 Circuit No Signal

AutoCodes https://www.autocodes.com > p0717_jeep
Repair Information for P0717 Jeep code. Learn what Input Speed Sensor 1 Circuit No Signal means, location and how to repair?

Similar to this

https://jeepspecs.com/wj-generation/wj-jeep-parts-equipment/transmission-input-output-speed-sensors/

..

For the 2008 Chrysler Town and Country, the transmission uses both an input (or turbine) speed sensor and an output speed sensor. These sensors help the transmission control module (TCM) understand the speed of the input shaft and the speed of the output shaft, allowing the TCM to adjust shifts and maintain optimal performance.

Location: Generally, on this model:

• The Input/Turbine Speed Sensor is located on the front of the transmission, close to the transmission cooler lines.
• The Output Speed Sensor is located on the front side of the transmission, typically more toward the driver's side.

However, accessing the exact location can sometimes be difficult due to other components in the way, and visibility may be limited.

Replacement Procedure: Here's a basic procedure for replacing these sensors:

1. Safety First: Disconnect the negative terminal from the battery to ensure safety.
2. Locate the speed sensor on the transmission.
3. Unplug the electrical connector from the sensor.
4. Use a socket or wrench to remove the bolt holding the sensor in place.
5. Remove the sensor. Sometimes they can be a bit snug or stuck due to dirt and grime.
6. Install the new sensor. Ensure that it's seated properly.
7. Reconnect the electrical connector.
8. Reconnect the battery terminal.
9. Clear any transmission codes using an OBD-II scanner.

Difficulty: The process isn't typically too challenging for someone with basic mechanical skills. However, the difficulty can arise if the sensors are stuck or if there's limited space to access them. Having the right tools and perhaps a flexible socket extension can make the process smoother.

It's always a good idea to refer to a repair manual specific to your vehicle for detailed instructions and illustrations. If in doubt, or if you encounter challenges, you might want to consult with a mechanic or professional before proceeding.

Lastly, the confusion online might stem from the various changes and designs Chrysler has used over the years, and the terminology might vary between sources. It's always best to cross-reference with a reputable repair manual or a trusted mechanic.

no scan tool errors told DTC.wow. or just guessing"?
well if you shop at the Kia site. Oem parts seller
and tell time your VIN, (not told) then you see all transmission parts. and how many speed sensor are there , 1 to 3 possible. for most transmission.
or buy the shop manual on your unstated transmission
no VIN
2.4 or 2.7L engine,USA?
i think the tranny is Hyundai.
wow dealer sells no transmission parts.!
the schematic shows 2 pulse generators inside the box
gen A and Gen B,

Does your versa have automatic transmission or CVT transaxle Makes a difference

Location is shown in a diagram here

https://www.2carpros.com/questions/input-speed-sensor-96916092
https://www.2carpros.com/images/question_images/235538/original.jpg

Full details on the code.

https://repairpal.com/obd-ii-code-p0717

..
..

Transmission will not shift. Code P0722 (transaxle output speed sensor). Where is it located? I can't find it or the input sensor. Google is no help!

On the drivers side. On the transmission, just above the cv axle.

On the transmission. Passenger side. about 6 inches from the axle , where it goes in the transmission.

The input speed sensor is located on the transmission. Located externally on the drivers side. There are to sensors. They look similar but one will be the input sensor, the other is the output. The input sensor is closer to the front.

It is located on the front of the transmission. you will see 2 of them one on the left under small transmission lines it is the input then to the right behind the radiator overflow there is the other one. Easiest way to change them is with a 1" deep well socket