When setting the cruise control on a 1997 saturn sl2, it does not set but slowly speeds up. Why?
SOURCE: 2001 Saturn SL2 shifting hard jerks...sometimes
This could be a dirty filter. i would start there and replace fluids with lucas tranny fluid. Does it change when the car warms up i wonder ?
SOURCE: Where is the fuel filter on a 1997 Saturn SL2?
It is an inline fuel filter under the car in the frame rail up front neat the motor area. It will look similar to this...
On that saturn it has a hose already attached to the fuel filter. It has what they call quick connects on both sides. just remove one side of air intake. (the one closest to firewall of car) where you can get your arm in there. Reach right under fuel filter and grab two white or green tabs with pointer finger and thumb. and squeeze till they make a snaping noice. then all you have to do is reach under fuel filter and pull hose off. Then push the black clips around fuel filter out and it should slide out. The same on the hose already connected to the fuel filter
SOURCE: Where is the transmission temperature sensor
It is located on the transmission side that faces the front of the car. It's just left and below the transmission spin on filter. It's the same sensor for the Engine Coolant Temp sensor and the Intake Air Temp sensor.
SOURCE: where is the transmission range
it is on the top of the transmission under the transmission shift cable post, here is a picture of it.
Testimonial: "Thank you very much"
SOURCE: how to remove headlight assembly on 1997 Saturn
check behind the headlight in the engine bay, you will find the nuts holding the headlight in place there but you may have to remove the battery or aircleaner box to get to them
?€¢
The On/Off switch
?€¢
The Resume/Accel switch
?€¢
The Set/Coast switch
?€¢
The TCC brake switch
?€¢
The stop lamp switch
?€¢
The throttle actuator control (TAC) motor
?€¢
The vehicle speed sensor
Cruise Control Engaged
The cruise control system will engage and adjust the vehicle speed based on the activation of the following cruise control switches:
?€¢
On/Off
?€¢
Resume/Accel.
?€¢
Set/Coast
The cruise control switches are located on the multifunction/turn signal lever.
The powertrain control module (PCM) monitors the signal circuits of the cruise control switches in order to determine when to capture and maintain the selected vehicle speed. The PCM uses the throttle actuator control (TAC) module motor in order to control the vehicle speed. For further information on the TAC System, refer to Throttle Actuator Control (TAC) System Description in Engine Controls - 4.2 L.
Ignition positive voltage is supplied from the 10 ampere HVAC 1 fuse to the cruise control switch via the ignition 3 voltage circuit. When the normally open cruise control On/Off switch is turned On, the switch closes and the PCM detects a high signal voltage on the cruise control on switch signal circuit. When the normally open Set/Coast switch is pressed, the switch closes and the PCM detects a high signal voltage on the cruise control set/coast switch signal circuit. To engage the cruise control system, turn the On/Off switch On and momentarily press the Set/Coast switch. The PCM will confirm that the cruise control enable criteria has been achieved. The PCM will engage the cruise control system and record the selected vehicle speed. The PCM sends a class 2 message to the instrument panel cluster in order to illuminate the cruise control indicator. Pressing the accelerator pedal, while the cruise control system is engaged, will allow the driver to override the cruise control system in order to accelerate the vehicle beyond the current set vehicle speed. When the accelerator pedal is released, the vehicle will decelerate and resume the current set vehicle speed. The driver can also override the current set vehicle speed via the Set/Coast switch and the Resume/Accel switch. When the cruise control system is engaged, pressing and holding the Set/Coast switch will allow the vehicle to decelerate from the current set vehicle speed without deactivating the cruise control system. When the Set/Coast switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily pressing the Set/Coast switch will allow the vehicle to decelerate at 1.6 km/h (1 mph) increments for each time that the Set/Coast is momentarily pressed, with a minimum vehicle speed of 37 km/h (23 mph). When the normally open Resume/Accel switch is activated, the switch closes and the PCM detects a high signal voltage on the cruise control resume/accel switch signal circuit. Activating and holding the Resume/Accel switch, when the cruise control system is engaged, will allow the vehicle to accelerate to a greater vehicle speed than the current set vehicle speed. When the Resume/Accel switch is released, the PCM will record the vehicle speed and maintain the vehicle speed as the new set vehicle speed. When the cruise control system is engaged, momentarily activating the Resume/Accel switch will allow the vehicle to accelerate at 1.6 km/h (1 mph) increments for each time that the Resume/Accel switch is momentarily activated, with the maximum acceleration total of 16 km/h (10 mph) over the current set vehicle speed . Momentarily activating the Resume/Accel switch, after the cruise control system has been disengaged by pressing the brake pedal, will recall the previous set vehicle speed that is recorded in the PCM.
95 views
Usually answered in minutes!
×