2000 Dodge Caravan Logo

Related Topics:

A
Anonymous Posted on Jul 16, 2014

How to removing front bumper cover from a 2000 caravan se ?

5 Related Answers

Ajkill

Anand Kumar

  • 2035 Answers
  • Posted on Feb 27, 2009

SOURCE: I need to remove and replace a front bumper cover

Please click on this link:
http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c15280089d63

Good luck...

Ad

Anonymous

  • 10 Answers
  • Posted on Mar 07, 2009

SOURCE: How do you replace rotors on a 1993 Dodge Caravan SE?

Cause thair are Pins Holding them in if u Look again u can see Very Simple Fix also when u go to Remove them use WD 40 to Losein them up frist

alicantecoli

Colin Stickland

  • 22516 Answers
  • Posted on Apr 25, 2009

SOURCE: i have a 2001 front bumper cover and a 2004 stratus

havent a clue ??try it and see if it looks the same then it should fit, if fittings a bit different then a drill and a couple of nuts and bolts

Anonymous

  • 435 Answers
  • Posted on Sep 10, 2009

SOURCE: REMOVAL OF REAR BUMPER COVER ON 1997 DODGE STRATUS

See under the bumper its strap with clips,you must take it out from it,

Testimonial: "I found out there are clips on each side of the b umper under the rear 1/4 panels as well. thanks"

baugh55grfmj

Mitchell Baughman

  • 225 Answers
  • Posted on Dec 29, 2009

SOURCE: how do i replace front drivers side brake caliper?

Jack the van up, remove the tire. Then you will see the caliper. There will be 2 bolts that hold it on to the rotor. Remove the bolts and pry it off with a screw driver or what ever works. Then disconnect the break line from the caliper. After you get the new one use a c-clamp to press the piston down into the caliper and install the brake pads. Bolt the caliper back into place and install the line. Loosen up the bleed valve on the caliper 1/2 turn and have someone pump the breaks until no air bubbles come out. Once you have a smooth stream of brake fluid coming out the valve have that person pump once more and hold the pedal all the way to the floor. Then tighten the valve.

Testimonial: "thanks - simply stated- anyone could do this with these directions!"

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

How do you remove the headlight assembly on a 2013 Dodge Grand Grand Caravan?

You need to remove the plastic clips and retainers on the front bumper plastic bumper cover. Here is a video link. https://www.youtube.com/watch?v=NaorvwlINr4
0helpful
1answer

Dose anyone know how to remove a front bumper cover on a 2000 dodge caravan?

https://www.youtube.com/watch?v=BCaZGTz1WLw

Not the specific video for your vehicle but this can assist you in the general methods and procedures in replacing a front bumper cover.
1helpful
1answer

Location of 2004dodge caravan cooling fan relay show photo

Remove the front number. Ou will see it riveted to the bumper frame of the drivers side. If you remove the screws that holt the top of the bumper to the upper radiator cover and gently pull back on the grill part of the bumper you will see it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/jeremy_d728a59f986299fa

0helpful
1answer

2011 Dodge Caravan. Ran into a metal wheelchair ramp rain. Drove back - dislodged - the black trim insert near the bottom of the plastic bumper cover. That black plastic thing has to be just put back on...

Hello Bruce...here are the steps to follow per All Data.

Release hood latch and open hood.
Remove the headlamp assemblies.
Hoist vehicle and support with safety stands.
Remove the five push pin fasteners attaching bottom of fascia/air dam to radiator closure panel.
Remove front wheels.
Remove front wheelhouse splash shields fasteners as necessary to gain access to bolts attaching front fascia to fender.
Remove the two bolts and two nuts attaching fascia to the front fenders (Fig. 1) and (Fig. 2).
Disconnect fog lamp wire connectors, if necessary.
Lower vehicle.
Remove two bolts attaching the upper grille support to the headlamp mounting panel at each side of the grille.
Remove bumper fascia from vehicle.
INSTALLATION

Position front bumper fascia on vehicle (Fig. 1) and (Fig. 2).
Install the two bolts attaching fascia to headlamp mounting panel at each side of grille.
Hoist vehicle and support with safety stands.
Install the two bolts and two nuts attaching fascia to the front fenders. The fascia should be flush to fender.
Install front wheelhouse splash shields fasteners.
Install front wheels.
Connect fog lamp wire connectors, if necessary.
Install the five push pin fasteners attaching bottom of fascia to radiator closure panel.
Lower the vehicle.
Install the headlamp assemblies.

The "push pin fasteners" are the pain you are having i believe. They push in, but to get them out you need squeeze them on the back & pull at the same time. If you happen to break a few, you can buy them in various sizes at the auto parts store. I hope this information is helpful, an owners manual will not have any info like this in it.



12_2_2011_5_37_49_pm.jpg
0helpful
2answers

How do I remove the front bumper cover on a 1995 Mercedes S420

Under the front of the car on the engine compartment should be nuts that you can remove to remove the cover.
0helpful
1answer

How do you remove a headlight 'assembly' (not the

You have to remove the front bumper cover. Put the car on jack stands (the front) and remove the inner fender plastic. You'll need a long extension and a 10mm socket to remove the nuts and bolts holding the bumper cover in place. Once the cover is off removal of the headlight becomes obvious.
0helpful
1answer

Front hood on Grand AM 2003 SE - hood and front bumper has a gap

Since you are replacing the bumper cover is it safe to say you have had some type of front impact. Any impact could have moved the location of the bumper mounts or shifted panels, or the hood.
1helpful
1answer

2000 VW Beetle: Need info on replacing front bumper cover. How to explanation

to take off the front bumper the fenders must come off as well. they are attached to each other and then bolted to the car. From what i remember there were like 90 screws to take off. so basically remove the headlight and the turn signals. then remove about 90 torx screws and pull the hole thing off. thene remove the fenders from the bumper, put them on your new bumper and mount them in reverse order!
0helpful
1answer

2000 grand caravan -had new front bumper installed now the interior temperature printout doesnot work-where is that outside sensor located?? need to know where the sensor for the interior display of...

It should be attached to the front of the lower radiator support behind the front fascia. Look for the two wire pigtail harness hanging loose if the sensor is missing or you can't find it.
2helpful
2answers

Starter on a 1997 Dodge Grand Caravan SE

Right in front on v-6 models. Driver's side,front,bolted to the transmission.
Not finding what you are looking for?

320 views

Ask a Question

Usually answered in minutes!

Top Dodge Experts

ZJ Limited
ZJ Limited

Level 3 Expert

17989 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15088 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

7339 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...