12641127123 cam numbers for comp camshafts?

code p 0341 refers to camshaft position sensor (CMP) sensor A bank 1--range /performance problem=== causes --insecure sensor/ rotor --- air gap--- wiring ---CMP sensor
you will have 2 camshaft position sensors ( one for each cam shaft but they should be the same unit
the sensor receives an impulse from the rotor on the cam shaft and that impulse has to be within the set parameters in the ECM
the air gap is critical to that impulse

Look up the number on the block that you pulled it from you,ll get your lift and duration if stock cam and or look for stamp on cam if not stock this link shows how to measure the cam also

How to measure camshaft lift - YouTube

? 2:28
www.youtube.com/watch?v=D0WaGnhklso
Feb 25, 2012 - Uploaded by Emil Davis
Here I show you how to measure camshaft lift with the cam out of the the engine. All you need ...

you will have more problems than a one legged man in great comp if you try changing the cam alone. Fuel and timing remapping, cooling upgrades, exhaust sytem upgrades... are you sure it\'s worth the effort?

In this case the solenoid needs to be replaced.The error code in this case is P1533.This code is many a times noticed on Mercedes Benz.
Click this link to go through the replacement procedure of adjustable solenoid:-----http://technoanswers.blogspot.in/2012/02/how-to-replace-adjustable-camshaft.html
-----------Also i recommend you to go through this additional help links for more help:-----Crankshaft and camshafts timing marks?http://technoanswers.blogspot.in/2012/02/crankshaft-and-camshafts-timing-marks.html
dual over cam timing mark details?http://technoanswers.blogspot.in/2012/02/saturn-vue-30-dual-over-cam-timing-mark.htmlHow to Inspect Camshaft?http://repairhelpcenter.blogspot.in/2012/02/how-to-inspect-camshaft.html
camshaft Timing specifications?http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
Camshaft, Bearings & Lifters Replacing ?http://howtobyme.blogspot.com/2011/12/camshaft-bearings-lifters-replacing-on.htmlCrankshaft Damper Replacement?http://schematicsdiagram.blogspot.com/2011/12/crankshaft-damper-replacement-on-honda.htmlCamshaft Position (CMP) Sensor replacing?http://schematicsdiagram.blogspot.com/2011/12/gmc-camshaft-position-cmp-sensor.html
Crankshaft Front Seal?http://schematicsdiagram.blogspot.com/2011/12/crankshaft-front-seal.html
How test cam shaft? Testing Car Camshaft?http://repairhelpcenter.blogspot.in/2012/02/how-test-cam-shafttesting-car-camshaft.html
Problem with cam synchronizer?http://technoanswers.blogspot.in/2012/01/problem-with-cam-synchronizer-on-1996.html
How to service Cam Shaft? Camshaft servicing?http://repairhelpcenter.blogspot.in/2012/02/how-to-service-cam-shaft-camshaft.html
How to replace Camshaft? Replacing Vehicles CamShaft Assembly?http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-camshaft-replacing.html--------This will help.Thanks.

For camshaft timing spec,click the link below :----Ford Mondeo ST220 camshaft Timing specifications? http://technoanswers.blogspot.in/2012/02/ford-mondeo-st220-camshaft-timing.html
-------This will help.
Also check this related help links:---

How test cam shaft? Testing Car Camshaft? http://repairhelpcenter.blogspot.in/2012/02/how-test-cam-shafttesting-car-camshaft.html
----------How to Inspect Camshaft? http://repairhelpcenter.blogspot.in/2012/02/how-to-inspect-camshaft.html
------------Crankshaft and camshafts timing marks? http://technoanswers.blogspot.in/2012/02/crankshaft-and-camshafts-timing-marks.html
----------Camshaft, Bearings & Lifters Replacing ? http://howtobyme.blogspot.com/2011/12/camshaft-bearings-lifters-replacing-on.html
---------Camshaft Position (CMP) Sensor replacing? http://schematicsdiagram.blogspot.com/2011/12/gmc-camshaft-position-cmp-sensor.html
------------How to replace Camshaft? Replacing Vehicles Cam Shaft Assembly? http://repairhelpcenter.blogspot.in/2012/02/how-to-replace-camshaft-replacing.html
---------This will help too.Thanks.

P0204 is miss fire detected on #4 cylinder.

Below is TSB from VW on your problem...a common one.


Technical Product Literature Transaction No.: 2015153/1
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory Release date: Jun 29, 2007
Condition
15 07 04 June 29, 2007 2015153
MIL ON, DTC P0087, P1093 or P2293 Stored in ECM Fault Memory
MIL ON with the following DTCs may be stored in ECM fault memory:
DTC Description
P0087 Fuel Rail / System Pressure - Too Low
P1093 Fuel Trim 2, Bank 1 Malfunction
P2293 Fuel Pressure Regulator 2 Performance

Technical Background
Excessive wear of intake camshaft lobe that drives the high pressure fuel pump. The wear limits maximum pump piston lift, causing fuel rail pressure fluctuations.
The wear on the camshaft lobe can also lead to wear on the base of the high pressure fuel pump cam follower.
Production Solution
Increase surface hardening of camshaft lobe for the high pressure fuel pump
Improved intake camshafts have Part No. 06F109101B.
Service

• Remove the high pressure fuel pump and visually inspect:
1. Base surface of the cam follower -6- in contact with the camshaft lobe.
2. Tip of the high pressure fuel pump plunger.
3. High pressure fuel pump camshaft lobe.

If the base of the cam shaft follower looks like -C- or -D-, no excessive wear is present.
Cam follower and camshaft should not be replaced.
If the cam follower base surface is excessively worn so that its surface is concave -B- or missing -A-, inspect the intake cam shaft lobe for wear.



If the high pressure fuel pump camshaft lobe shows excessive wear, replace the intake camshaft with Part No. 06F109101B and the cam follower with Part No. 06D109309C, see Group 15 Engine - Cylinder head, Valvetrain in ElsaWeb.

Inspect the tip of the high pressure fuel pump plunger for excessive wear.
If excessive wear is found the high pressure pump must also be replaced, see Group 20 Fuel supply in ElsaWeb.
Tip:
High pressure fuel pump plunger damage is only possible if the cam follower base has a hole in it and the plunger tip has come in direct contact with the camshaft lobe.
If no excessive wear can be found in the high pressure fuel pump cam follower or intake camshaft lobe, or if the damage is found in camshafts with part number 06F 109 101 B, create a Technical Assistance Contact Ticket under the Concern Type Engine and Engine Electronics in ElsaWeb.
Attach the complete diagnostic log to the contact, and call the VW Technical Assistance Center for further assistance.

Warranty
When procedure applies to vehicles within the New Vehicle Limited Warranty, use the following:
Claim Type: W2
Part Identifier: 1505
Damage Code: 1505 18 _ _ _* 2
Labor Operation:
2.0T FSI engine Use applicable SRT time in ElsaWeb
Diagnostic Time: Actual GFF time expenditure
Claim Comment: Input "As per Technical Bulletin 2015153" in comment section of Warranty Claim.

* Code per warranty vendor code policy.
Required Parts and Tools
Description Part No: Quantity
Intake Cam Shaft 06F109101B 1
Cam Follower 06D109309C 1

No Special Tools required.

when you crank the engine over now, does it sound different than before? if yes, you probably have a broken timing belt. it is also common for the cam gear to slip out of position from the cam and cause an incorrect, but hard to diagnose, timing issue. other no start with check engine light on issues could be a faulty cam or crank sensor.

pull the codes from the vehicles computer. if there is a cam or crank sensor code, or if there is a code that says in some different wording "cam sensor signal does not match crank sensor singal", first check crankshaft to camshaft timing. if belt is ok and timing marks line up then i strongly suggest removing the bolt from the camshaft that holds the cam gear on. with the bolt and cam gear removed you should be able to tell if the cam gear has rotated on the camshaft. there should be a small pin sticking out of the camshaft. if it is broken off then you need to replace the camshaft. if the pin is still there and the timing is good then replace iether the cam or crank sensor depending on what code you have stored in the ecu memory. if the code is not for the cam/crank sensor then google search the code number e.g. "p0502" and your make and model.

Number P0013 Description "B" Camshaft Position - Actuator Circuit/Open
Type: Powertrain - Fuel and Air Metering - ISO/SAE Controlled

Location Bank 1
Notes The "B" camshaft shall be either the "exhaust," "right," or "rear" camshaft. Left/Right and Front/Rear are determined as if viewed from the driver's seating position. Bank 1 contains cylinder number one, Bank 2 is the opposite bank.

The cam actuator is the one that makes possible the retarding and advancing of the Cams..
You must have a cam actuator harness problem or an electric failure in the internal actuator, check if the actuator harness and wires are not broken, check if they are receiving good voltage, If they are good, you almost have a failure in the actuator and you will have to replace it.....

if the cam is out of time it will give a code it may have jumped a tooth and now the cam is out of time or the belt is just really loose and the comp thinks its out of time and a belt that has jumped a tooth will make the engine run like ****

Sounds like a throttle position sensor, but the comp should be coding the error in any case. How did you know to replace the crank and cam sensor?