Replace rubber cv boot on 1999 Isuzu rodeo - 1999 Isuzu Rodeo

SOURCE: power windows isuzu rodeo 1999

Cable must of disconnected need to take door cover off and reconnect...

SOURCE: cv joint replacement 1998 isuzu trooper 4x4

This is a simple job that is why it is not very detailed in your book. Nothing special. Do one side at a time so you have a reference to how to reassemble it. Remove your tire , brake calipers be sure not to stress the rubber brake lines or open the brake lines to air. Remove both upper and lower ball joints. When taking out the ball joints remove the cotter pin and bolt and beat the **** out of the joint for it to release. Then the C/V axles will come right out with a bit out encouragement. You will need a few tools wrenches pry bar hammer. I would buy a Chilton's or a Haynes repair manual for torque specs for reassembly. Good luck and take your time. And unless the axles are making noise you can just replace the rubber boots. Which is alot cheaper.

SOURCE: how to replace front cv shafts on a 1997 isuzu

rejakwilson @ aol.com For Full Illistrations (PICTURES) PREPARATIONS:

1. Jack up the vehicle and support it using jack stands.
2. Remove the tire and wheel.
3. Remove the drain bolt to drain differential oil.

• During the work, be sure that the differential case is supported by the jack.
• Remove the brake caliper fixing bolt and hang the caliper.
• Remove the antilock brake system speed sensor. (If equipped with antilock brake system)
  

1. Hub assembly (Disc, back plate and knuckle):

1. Remove the locking hub.
2. Disconnect the knuckle and the suspension arm.

1. Steering link and arm assembly.
2. Suspension crossmember.
3. Propeller shaft.
4. Protector.
5. Breather Hose:

1. Remove the hose clips.
2. Disconnect breather hoses from front drive axle tube and disconnect housing.

1. Vacuum Hose. Disconnect vacuum hose from actuator. Shift switch connector (7a).
2. VSV Assembly. NOTE: Be sure not to remove hose and connector from VSV assembly.
3. Mounting bolt and nut.
4. Washer and spacer.
5. Bolt. Remove the mounting bracket fixing bolt.
6. Front axle case assembly and front drive shaft assembly (LH side). Lower the vehicle and disconnect the RH front drive shaft assembly, and then remove the front axle case assembly and front drive shaft assembly (LH).
7. Front drive shaft assembly (RH).

Charles McElchar

• 389 Answers
• Posted on Sep 28, 2009

SOURCE: change a cv boot on a 1996 isuzu trooper

First their are two different front axles in 1996 troopers. Isuzu changed the 4wd system from auto lock hubs to drive control axle.auto lock hube are on the older trooper's with the light and wiper switches on the dash. The same way to change both. Auto hub remove the six hex. screws slide off the hub remove the sirclip from the driveshaft. Newer hub has 6 alan-head screw's again remove them then the hubcap then the sirclip on the shaft and slide off the round spacer. Next 4 bolts from the lower balljoint and the brake's. Pull out the hub until it clear's the shaft remove the inner boot clips slide the inner boot out the shaft. Clean the grease from the end of the axle then with your fingernail feel along any of the 3 tracks in the axle and near the outer end of the track you will find a wirelike split ring slide a screwdriver under the ring and lever it off . Pull out the drive clean off the grease. You will see a sirclip on the end of the joint remove it and slide off the joint. You can replace either boot from that end. The outer joint is held on with a snap ring on the shaft inside the joint and is not easily removed need a hammer and drift to drive off the end and when removed its hard to get the snap ring on the shaft back into its place.You can change both boots from this end as well. Cheers

Duane Wong

• 6826 Answers
• Posted on Aug 03, 2010

SOURCE: Replacing turn signla electronic flasher for 1999

Get the proper flasher from the parts store and start searching under the dash for the one that clicks when the turn signals are operating.