Where is the number 1 cylinder? 2000 jimmy - 2000 GMC Jimmy

The firing order is 1, 6, 5, 4, 3, 2. Stand with the engine belts and pulleys nearest to you and the transmission furthest away.
The cylinders on the Left side are the Even numbers, Number 2 is nearest to you, number 4 in the middle and number 6 furthest away from you.
The cylinders on the Right side are the Odd numbers. Number 1 is nearest to you, number 3 in the middle and number 5 furthest away from you.
Take a close look at your distributor cap. Some are actually marked with the numbers 1 to 6 showing which where each spark plug wire should go.

Check out the link. click on the images tab. You really need a service manual.

https://www.google.com/search?q=2000+gmc+jimmy+headlight+wiring+diagram

2000 gmc jimmy service repair manual - SlideShare

https://www.slideshare.net > 2000-gmc-jimmy-service-r...
Jun 16, 2017 - 2000 GMC JIMMY Service Repair Workshop Manual provides step-by-step instructions based on the complete dis-assembly of the machine. It is this ...

GMC Jimmy Repair & Service Manuals (71 PDF's - Onlymanuals

https://www.onlymanuals.com > gmc > jimmy
How to download a GMC Jimmy Repair Manual (for any year). These Jimmy manuals have been ... 2000 - 2000--GMC--Jimmy 2WD--6 Cylinders W 4.3L FI OHV--32627901.

2000 GMC Jimmy Service Repair Manuals on Motor Era

https://www.motorera.com > auto-service-repair-manual
2000 GMC Jimmy Service Repair Manuals for factory, Chilton & Haynes service workshop repair manuals. 2000 GMC Jimmy workshop repair manual PDF.
..

when engine light blink it is only one thing.......misfire you could have P0300,P0301 and so on
P0300 is multiple misfire
P0301 is cylinder no 1 misfire,the last number tell you the no cylinder
hope it helps

the problem is the passlock .This system allows starter operation,then kills the injectors 1-2 seconds after startup.The key cylinder housing has a small magnet that rotates past the passlock sensor.The sensor is powered and detects rotation.This is a Anti-Theft System for 2000 jimmy

For the 4.3L (6Cyl)
Firing Order:
1-6-5-4-3-2

Cylinders:
(back of engine)
| 6 |---------| 5 |
| 4 |---------| 3 |
| 2 |---------| 1 |
(front of engine)

Distributor:
...(back)
(+)..4...3
.5...........2
....6...1..(+)-screw
...(front)

Let me know if this helped or if you have additional information or questions. Feel Free to contact me at FixYa.com!

Firing Order is 1-6-5-4-3-2
Number 1 plug is located drivers side front of engine.

http://autorepair.about.com/library/firing_orders/bl-fo-3161.htm

That depends on the engine and fuel system. For example, throttle body runs around 12 PSI as where fuel injection (Injectors on each cylinder) can run up to 40 PSI. Run the pump that fits your vehicle!

WELL THE FIREING ORDER IS 1-5-3-6-2-4 #1 IS CLOSES TO CRANK SHAFT PULLY HOPE THIS HELPS

Ok that's pretty simple Put cylinder # 1 on TDC= top dead center on the (compressionstroke piston all the way up). Mark on metal part of distributor (with marker) where the number one is on the cap( that's where the number 1 wire plugs in) Then in-plant distributor make sure that rotor point is pointed to #1 on the cap, turn distributor shaft until this is achieved or as close as possible try to center shaft so you can adjust... ****** or advance to fine tune after you in-plant distributor if needed. Contact if you need more help . Good Luck

If you just need a key the dealer could make you one with the serial number and proof of ownership. If not you have to drill out the tumblers.